Ford 6.0L Power Stroke Diesel :: Low Compression Results - Slight Brown Haze On Cylinders
While I had my glow plugs out to crank the motor for the HPOP work I have done I checked the compression on all the cylinders. 6 of the cylinders were 275-280, got 250 and 110 on the others. I put oil in both the low cylinders and the 250 went to 260 and 110 went to 150. I pressurized the low cylinder and with the valves closed it was leaking out the exhaust manifold also had a small amount of coolant come out the water pump. Removed the cylinder head and didn't see anything unusual with the cylinder that was reading low in fact the if was the best looking cylinder of the four with nice looking crosshatch on the cylinder wall.
The other three cylinders has some slight brown haze on them which I assume is rust. This motor probably hasn't run in 18 months and the truck was a non-runner when I purchased as a theft recovery, no history on the truck. Taking the one head to a shop for them to check it out. What's the opinions out there with the low compression? Be ok once it runs and rings get coated with oil? The motor is out of the truck so maybe I should tear it down completely hone and put new rings in it.
Ford 7.3L Power Stroke (1999-2003) :: Burning A Lot Of Oil / Low Compression On 2 Cylinders?
2000 f450, truck has been running great and then all of a sudden starts running really rough. I check the oil and its dry! it was 9 quarts low! i checked the oil 2 weeks prior as i often do. i change the oil every 4500 miles and now this. i had driver side injectors done about 5 months ago. I take it to my mechanic and he said he thinks it has low compression on 2 cylinders but didn't do a compression check( not sure how he knows). He told me to run it until it pukes , keep putting oil in it with lucas oil additive. Then i will have to have the engine rebuilt. The truck only has 175000 miles! i thought these things were supposed to run forever! Does this seem right to you guys? I bought the truck a year and a half ago and have always kept up with it. has dp tuner but everything else is stock. Smoke comes out of the oil fill tube slowly but doesn't send puffs like a locomotive. mechanic said the turbo is fine.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - No Compression In Any Cylinder
I bought an 06 6.0 f 350 4x4 dump bed cheap. seller said it was sitting for 1-2 years and wouldn't start. ficm is at 48 volts fuel pressure is at 100 oil pressure builds fine, then checked compression and reading no compression in any cylinder. My mechanic says new motor or possibly both head gaskets are blown.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - No Start Intermittently / Slightly Low Compression On One Cylinder
Started having some crank no starts intermittently. Scanned and found codes for cam sensor. so I was in a pinch and a hurry on a sunday so I picked up a BWD brand cam sensor from parts store and installed. I have not seen this issue since but started noticing other thing going on. I noticed a few weeks ago my truck was starting a little strange. as it would spin over before firing off, it didn't sound right. I couldn't pinpoint if it was due to slightly low compression on one cylinder or one cylinder had a little fuel or oil in it and that one cylinder was actually firing while cranking over.
I also was noticing a little longer crank times than normal. didn't matter if engine was cold or hot. sometimes would fire up quick and sometimes it took a few seconds. most of the time I couldn't catch it on my scanegauge if the ICP was low due to the lag on the scangauge.
Well one day on my way home from work (50 miles one way) I stopped about half way to fuel up. after filling up and attempted to restart the truck it really acted like it didn't want to start but did after cranking for about at least 10 seconds and started rough. and of corse my scangauge decied to hate me this day because it would show any data until I unplugged it and plugged it back in. so started home. felt like it had a very very light miss on the way home. when I slowed down to turn onto my road the truck died. took forever to get it to start back up. this time the scangauge was reading and I could see ICP was between 300-400 and IPR was 85%. so low pressure and not reaching the 600 needed to fire. once it started I limped it home. scaned it with my Auto Enginuity and it didn't show any codes.
So that much I can see I have a leak on the HPO system. but I done a lot of work to the truck about 2-3 years ago. roughly 80k-100k miles since the work. what I done included...
OEM oil cooler
OEM (updated)dummy plugs, standpipes & STC fitting
OEM head gaskets and ARP studs
BPD EGR cooler (I should have deleted)
ALL other engine gaskets(Bed plate, oilpan, front&rear cover, ect.)
OEM glow plugs and harness
OEM blue spring upgrade
Cleaned turbo veins
2 OEM REMAN injectors. (cant remember which two) had contribution codes one on each side.
This is all I can remember right now. Now have yall seen the updated dummy plugs and standpipes leak? I have not pulled valve covers to air test the HPO system yet.(don't have my air compressor at my new house yet). Here is what I have done so far:
Fully charged batteries.
I did do a bubble test. pulled upper fuel filter cover off and removed filter topped the bowl off and turned engine over using the wire by the passenger side battery. some bubbles but not a bubble bath.
Checked fuel pressure (not running) its 60psi. did not start truck because I need a different fitting so I can run the truck and check pressure while running.
while doing the bubble test I could hear that one cylinder is low on compression. but I do not have any misfire or contribution codes.
when I ran contribution test on AE its not showing any particular cylinder lower than the rest. but the line is not very solid at all.
Here is what I plan to do.
Compression test on each cylinder.
Looking at the Harbor freight kit. Looks like it has fittings for glow plug and injector holes.
If I can do compression test on both glow plug and injector holes this should show weather my injector orings are the cause of the low compression.
Then I have to airtest the HPO system and find the leak.
Am I on the right track? what else should I check? Guess I should add that the truck currently has 297K miles.
Ford 6.0L Power Stroke Diesel :: 2005 - Faint Ticking Sound / No Compression / Timing Gear Failure
2005 6.0 SuperDuty ... I was driving my truck on the freeway, no issues. Started hearing a very faint ticking sound, then the engine died. Pulled off to the side. tried to start it, and it turned over very rapidly, with no compression. I'm thinking "Timing Gear".
Had it towed to a Ford dealership near the incident. I told them what i thought it may be, and the mechanic thought it "May be possible". not very confidently....
I authorized them to remove the engine, and look. Sure enough, the gears were toast. This is the difficult part.
The service manager is a young kid, (I can tell from talking to him a hundred times on the phone), and is telling me "My Cam(s) are ruined, and the valves are bent, because the metal from the gears went through the motor. I told him to stop. put the truck outside, and wait. So, I have a couple of questions. other than i don't have Cam(s).
1. Is the 6.0 a clearance type motor? (will the valves impact the pistons, if the timing gears fail).
2. Will the metal from the timing gears get into the motor, or fall into the oil pan?
There were no loud noises, when the engine died. I had the engine bullet proofed at 101,000 miles, it now has 250,000. The truck is still solid, so worth fixing?
Ford 6.7L Power Stroke Diesel :: 2014 F350 - Two Cylinders Misfiring
2014 F350 6.7... The truck has only 30000 miles on it. I was driving uphill and the engine just quit, but fired up right away after with engine check. On idling run at 500-700 rpm , no power, clicking noise , sometimes shaking. Took to the closest dealer right away, they don't know what is it, but they want to rake of the engine . This truck is not under any warranty. This is my first diesel truck, didn't expect anything like this....
View 4 RepliesFord 6.0L Power Stroke Diesel :: When Starting Acts Like Truck Only Running On Half The Cylinders
I have a 04 6.0 and lost with it. I parked it the other night and in the morning I went to start it and it acts like it's only running on half the cylinders. I haven't had any issues till now so I replaced fuel filters and air cleaner is fresh but no change. It is not throwing a check engine light it isn't smoking excessively. I don't know where to check next.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Running Rough / Misfire On Cylinders
I have a buddy at work who has an 04 f350 6.0 that is running very rough. we put a scanner on it and disabled the injectors and 1,7,8 have no change. He checked the FICM voltage and is getting 48 volts on crank and run. He checked the wiring for anything loose or rubbed but nothing seems wrong.
View 14 RepliesFord Ranger / B-Series :: 1997 4.0L - 0 PSI Compression On 3 Cylinders
I've been fighting some issues with the truck and decided to do a compression test to decide if I want to try to keep 'Old Yeller' alive or not. I'm all for working on it until I have to dig into the lower end of the motor. I rented a compression tool and the results were a little shocking. I did this test with a slightly warm motor, fuel pump relay pulled, all spark plugs pulled and throttle @ 100 %. Motor turned over 10 times for each cylinder. I even moved all the rubber o-rings on the tool up on the threads to make sure I was getting a good seal.
Cyl 1 - 40
Cyl 2 - 0
Cyl 3 - 0
Cyl 4 - 80
Cyl 5 - 0
Cyl 6 - 60
Needless to say I didn't even bother doing this wet. My only real question is can this be close to accurate. I drive the truck daily. 160k mi on it.
I'm fighting the dreadful P0171 and P0174 codes and after a couple cycles I will get misfire codes. Its low on power (hard to keep @ 70MPH with some wind) and gets 10MPG right now. However it starts and runs and stays consistent (even though it rumbles like it has a nice cam in it).
Is it time to put Old Yeller down ? Are these compression results even remotely accurate ?
Ford - Engines - Escape :: 2008 - One Of Six Cylinders Has Compression Rate Of Only 25
My mechanic just told me I have one of my six cylinders that has a compression rate of only 25. I am weeping as I continue to pay my car loan. Looking for info, if this can be repaired vs. putting in a replacement engine?
View 5 RepliesFord Super Duty (1999-2016) :: 2015 F250 - No Compression On 3 Cylinders
I've got a 2015 F250 with a 6.2 Liter with no compression on 3 cylinders. The dealer just diagnosed it and has not opened it up yet but the mechanic says it is probably a broken valve spring...that it is not uncommon in this engine.
My concern is not repairing the spring my concern is what a "free spinning" piston in 3 cylinders does to the life expectancy of the main and connecting bearings in this engine. I have rebuilt engines in the past and I have bought re-built from auto parts stores and from Jasper and I have never had any last more than 60-70K miles. It seems to me that even with very little mileage on the engine with three of eight pistons jumping around under no pressure that there could be considerable scarring of the bearings or bearing surfaces. I am no expert by any stretch but this is an engine in atruck that has less than 22K miles on it and I ain't real happy about opening it up let alone trusting for the next 280K miles that the bearings have more wear on them than they should have. It was only driven about 20 miles total like this but that is a lot of pressure on a highly tuned and pretty darn precision machine.
This is the newest vehicle I have owned since 1988 and I meant for it to be the last pickup I drive (I drive 'em til the wheels fall off) but I am not overly confident that even if this is a one off problem that it hasn't caused even more damage that won't show up for another 100K miles or so???
Ford Super Duty (1999-2016) :: 2000 F250 5.4 - No Compression On Cylinders
I have a 2000 ford f250 5.4 2v that's been having a shaking at idle and no power what so ever. I tried diagnosing it myself and came up with nothing. I finally decided to take it to the dealer and they are telling me that the right side has no compression on 3 cylinders. They want almost 7000 for a new engine. I was wondering if it was possible to get away with just putting a new head on the right side?
View 13 RepliesTiguan :: 2011 Engine / No Compression On All 4 Cylinders
I had My VW tiguan 2011, Died all of a sudden, where went to supermarket and went out and the car is not starting at all.
So next morning had it towed to the dealership for investigation. Now after a week of tests and investigation and replacement of Fuel HP pump @ the engine still not working.
They did pressure test, and surprise came "no compression on all 4 cylinders".
They will need to open the engine and do further investigation. Hope it's just a gasket leakage
The car is still less than 5 years and mileage is 174K km, just made oil top up and general checks few days before the incident. all services @ dealership if not on-time, before time.
Lexus GS 2006-11 :: Car Died In Parking Lot - No Compression On All Cylinders
Wife's 2008 ES350 with 80k miles died in a parking lot. Wouldn't re-start with warning lights for Trac Off, Check Engine and VSC. Called tow truck from our local repair shop. Tow truck driver tied and started the car with no lights. Wife went ahead and had it towed.
Repair shop called and said that car started for tech but died w/o any warning lights. Shop started checking it out and found that it has no compression on all cylinders. In talking with service manager, we discounted the timing chain since the car will re-start, at least a few times. His gut feeling, something with the internal timing gears and such.
Repair shop has found a used engine locally and has it on hold while we decide what to do. The shop doesn't rebuild motor and just diving into it for exploratory surgery could be expensive with no assurance of positive results.
Ford 7.3L Power Stroke (1999-2003) :: Bad Cylinder - Smoking And Low Compression
I got a deal on a1997 f450 7.3 what does it take to swap to 2001 f250 7.3.mine has a bad cylinder with smoking nd low compression.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - White Smoke - Injectors / Lack Of Compression
I have a 2001 7.3 with 243k. I think the injectors are shot but other people including a local mechanic say it's not the injectors. What the truck does is smoke white. Sometimes little puffs when accelerating. Sometimes clouds that make the people behind you drop back a 100 feet. I have a ts6 on the truck and that alone with the 243k miles is enough to think its bad injectors. It smoke white. The exhaust is moist to the touch with soot built up like crazy. It doesn't really smell sweet and it's not really blue at all. It's getting horrible mpg. And lacks power. I don't have a high enough psi gauge to test compression. All arrows pointing to injectors?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Codes P1247 And P1248 / Noise Sounding Like It Lost Air Compression For A Few Minutes
My pickup has 316,000 miles on it. It's a 2000 ford f250 7.3 powerstroke. I have always bragged how my truck can pull anything because it has alot of power. Yesterday when pulling a 28' travel trailer up an incline I noticed I didn't have much power and it steadily got worse. Now I'm at a crawl when I hear a noise sounding like it lost air compression for a few minutes then the noise stopped. I stopped and looked to make sure everything under the hood was still attached and everything seemed fine.
I got back in and continued very slowly a few more miles home. Gauge were all good, never got hot. I put a scanner on it and it threw two codes. P1247 and P1248. I haven't noticed any unusual smoke. This is my second ford I've owned and know that when weather gets cold you may have to plug it in. But this truck it doesn't matter if it's 100 outside it will not start without plugging in for at least 1 hour. I've replaced all glow plugs hasn't worked. So I am assuming this break down now has something to do with it. I really am starting to not like fords!
Ford 7.3L Power Stroke (1999-2003) :: Oil Draining Into The Rear Cylinders
2001 7.3L 307,000 miles.... I have a couple of injectors pretty close to failing the buzz test.
I'm a shade tree mechanic - I've done the oil cooler, changed the radiator and belts etc how easy is the injector change? The bit that bothers me is the oil draining into the rear cylinders and ensuring that I don't hydraulic lock something. Do I need any special tools? Should I just take her to Diesel Innovations in Houston and let them get on with it ....
Ford 7.3L Power Stroke (1999-2003) :: Truck Running Rough And On Less Than 8 Cylinders
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 Replies