Ford Ranger / B-Series :: Shifting Hard / Clutch Won't Disengage At All After Master Cylinder Replaced
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
Ford Ranger / B-Series :: 1992 - No Heat / Power Steering / AC?
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
Ford Ranger / B-Series :: 2004 - Hard To Turn - No Power Steering?
My Daughters 2004 Ranger has about 195K the power steering reservoir is full it turns to the left as it should (assisted power steering) turning to right there is no power steering (manual Rack) I am thinking the issue is most likely in the steering rack..
View 2 RepliesFord Ranger / B-Series :: 1992 - Hard Start Almost Every Time
I'm working on a 1992 ranger with the 2.3l. Hard start almost every time, sometimes have to hold throttle open sometimes not. Won't start at all this morning. When it does finally start it takes a while for it to start firing on the intake side plugs. Haven't had time to check fuel pressure yet but can hear pump cycle when key is switched on.
View 8 RepliesFord Ranger / B-Series :: 1986 - Power Steering Shaking Then Spinning On Itself To Hard Left?
My 40 Ford pickup is on an 86 Ranger chassis and uses the stock Ranger steering gear. My question is about the connections on the steering box. I'm using a GM power steering pump and several steering gear vendors have told me that outside of needing to adjust the pressure for the correct feel, the combo works. I fired the truck for the first time tonight but the steering wheel went crazy, shaking around and finally spinning on it's own to a hard left.
Some quick research leads me to believe that I have the lines reversed but it would be great to know for sure. I did manage to find on e diagram of a Ford PS box on Google and it shows the lines reversed of what I have set up on my truck and I can't for the life of me remember how I figured out what the plumbing should be when I installed it. Which port on the box is the inlet and which is the return?
Ford - Ranger :: 2002 - No Clutch Pedal Or Shifting Hard
When I bought my ranger used, the clutch felt ok. But as a couple weeks had passed, it started to get hard to shift. The clutch doesn't slip at all so a friend of mine said there might be air in the system.
I would pump the clutch pedal a few times and then it would shift ok for a while, then back to shifting hard. I found the bleeder and had my son assist me with bleeding the system. Everything was fine at first but I made a big mistake and now i have no pedal feel at all.
My mistake was i didn't realize what I thought was the reservoir was not the actual reservoir. There was a black rubber thing in the reservoir that I filled with fluid. My mistake was I needed to take out this black rubber thing.
So now i am stuck with no pedal and don't know what to do. When I pulled out the black rubber thing, the reservoir was empty so i filled it and it bubbled for a second and then stopped. Tried pedal at this point and there is no feel at all. It just goes to floor with no effort.
Ford Ranger / B-Series :: 1998 - How Hard Is It To Replace A Clutch
I think the time is near for a new clutch in my 98 Ranger, 2wd/ 5 spd. How tough of a job is this? I've changed the one in my 66 Mustang years ago but things were less complicated then.
View 3 RepliesFord Ranger / B-Series :: 2003 - Grinding Noise While Shifting - Use Pressure Bleeder On Clutch System?
Just picked up a 2003 Ranger XL 2.3L and notice that I get a little grinding every now and then when shifting into 1st gear. The clutch was replaced 3 years ago according to the PO but had no clue as to how long it's been since the clutch was bled.
I've used my Motive pressure bleeder numerous times in the past on brakes with much success but I've never used it on the clutch. I've used vacuum bleeders as well but it's always a 50/50 success rate with that. The pressure bleeder just works much better for me.
Using a pressure bleeder on a clutch and if so any tips like still needing to tip the master cylinder end up to release any potentially trapped air bubbles?
Ford Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Ford Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Ford Ranger / B-Series :: 1997 - Clutch Pedal Hard And Could Not Depress It
This is unusual. After driving into town for new tires, the clutch pedal was hard and I could not depress it after the tire tech parked the truck. It did finally depress with a pop, though the pedal functioned there after the clutch did not function properly.
At times it seemed to be ok at other times it seemed weak. I stopped by Autozone and checked the fluid, seemed low and I added some. Continued home not completely confident that I would make it. Had to make one stop along the way.
Once again the clutch pedal was stuck at the top and would not depress. I finally slid the safety switch up the clutch shaft to start the truck, when the engine started the pedal depressed. I was able to continue home but the clutch is not functioning properly.
Ford Ranger / B-Series :: 1998 - O/D Light Flashing And Truck Shifting Hard
I am having a problem with my O/D light flashing and my truck shifting hard. Just started out of the blue. After reading a few other topics, I am hoping it is the VSS. Now if only I could find the dang thing. Looking for a diagram, or detailed description on where it's at?
View 14 RepliesFord Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesFord Ranger / B-Series :: 1989 Truck Jerked Really Hard - Lurch When Clutch All The Way Pushed Down
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
Ford Ranger / B-Series :: 1992 - Code 212 With CEL - No Power On Acceleration?
I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
Ford Ranger / B-Series :: 1992 - Both Power Door Locks Won't Working?
So I've got this 1992 Ranger extended cab with power door locks and neither side is working. It has power windows too and they work fine. I checked the 30amp fuse under the hood for the power door locks and it's good and checked it with a test light and it's good. What's most likely the cause that both sides don't work? Is there a way to troubleshoot with a test light to trace down the problem as a bad switch or actuator?
View 10 RepliesFord Ranger / B-Series :: 1992 - Lost Power On Freeway / Stopped And Couldn't Restart
I have a 1992 Ranger with 2.3L that suddenly lost power on freeway and stopped and couldn't restart. Towed it to Seattle, WA and need Ford Ranger 2.3L engine mechanic to double check the timing since new belt installed to make sure it was done right before cover and rest of engine reinstalled.
View 5 RepliesFord Ranger / B-Series :: 1988 Bronco II - Steering Pulls After Hard Left / Sight Pop?
I've been replacing my steering components over the past month and have fixed all the previous issues other than this one that's got me stumped. After I make a hard left the steering will pull left (very hard) until I either turn the wheel right or hit a bump. Sometimes when going immediately from a left turn to a right turn (or vice versa) I can actually feel a slight pop as it starts to pull.
The order of repairs thus far has been: new power steering pump, new inner & outer tie rod ends, professional alignment, new steering box with both lines. The shop and I both agree the ball joints are good. I've jacked my truck up by the frame and removed the wheels to check for steering/suspension play but have not been able to find any. 180k miles on the chasis.
Ford Ranger / B-Series :: 1983 - Poor Fuel Mileage?
I recently bought a 1983 Ford Ranger Diesel pickup truck (2.2L Mazda engine, manual transmission). The dealer said to expect a little above 30 mpg on fuel mileage but the two fill-ups I've done show an average fuel mileage of 22 mpg. About half of these are highway miles.
I thought diesels are supposed to have good mileage. Is this typical for my year and model truck? Is there any way to increase the mileage? I just replaced the air and fuel filters and also changed the oil and oil filters.