Ford Ranger / B-Series :: 1988 Bronco II - Steering Pulls After Hard Left / Sight Pop?
I've been replacing my steering components over the past month and have fixed all the previous issues other than this one that's got me stumped. After I make a hard left the steering will pull left (very hard) until I either turn the wheel right or hit a bump. Sometimes when going immediately from a left turn to a right turn (or vice versa) I can actually feel a slight pop as it starts to pull.
The order of repairs thus far has been: new power steering pump, new inner & outer tie rod ends, professional alignment, new steering box with both lines. The shop and I both agree the ball joints are good. I've jacked my truck up by the frame and removed the wheels to check for steering/suspension play but have not been able to find any. 180k miles on the chasis.
Ford Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesFord Ranger / B-Series :: 2004 - Hard To Turn - No Power Steering?
My Daughters 2004 Ranger has about 195K the power steering reservoir is full it turns to the left as it should (assisted power steering) turning to right there is no power steering (manual Rack) I am thinking the issue is most likely in the steering rack..
View 2 RepliesFord Ranger / B-Series :: 1992 - No AC And Power Steering / Poor Clutch Disengagement Resulting Hard Shifting
1992 Ford Ranger 4x2 with 2.3L engine and 5 speed manual transmission. 135,000 miles, no AC and no power steering. I am having poor clutch disengagement and resulting hard shifting. The shop added a little fluid to the reservoir last oil change and it is still looking full. I always park on concrete and never see any leaking. I don't know what may have been done before as I haven't had the pickup all that long. Where should I start? Is there probably internal bypass leaking in the hydraulic clutch as there seems to be no external leaking?
View 4 RepliesFord Ranger / B-Series :: 2000 - Pulls To Left Real Hard?
My 2000 ranger in 4x4 high never did this. And in 2wd it doesn't pull at all...
When in 4x4 high it pulls hard to the left ?????? is left not working? It has automatic hubs ...
Ford Ranger / B-Series :: 1986 - Engine Won't Firing
i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is
View 1 RepliesFord Ranger / B-Series :: 1986 Just Cranks But Won't Start
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 RepliesFord Ranger / B-Series :: 1986 - Gas Will Not Keep Engine Running
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
Ford Ranger / B-Series :: 1986 - Bogs Down When Put Into Throttle
1986 Ranger 2.3 inline 4
I just recently bought an 86 Ranger from a friend. It had recently stopped working and had no desire to fix it. So here I am. The truck will sit in park and rev all day long, once its in drive it idols fine and moves its self down the street. The problem occurs when I apply throttle. It begins to bog down and I cannot get past 20mph. I have replaced the fuel regulator and also I took the tank down and replaced the fuel pump. The fuel filter is two months old, and the throttle response sensor is two weeks old.
Ford Ranger / B-Series :: 1986 - How To Disable Front Differential
My front diff is busted, and I mean bad.. I can barely even run the truck 5mph, and it's very loud. The diff casing is even busted. I want to just disable it to drive in 2wd. What's the easiest way to do it? It won't disable using the push button control.
Can I just remove all the locking stuff in the front wheels, so there's nothing for the axles to grab on, and manually turn the solenoid at the transfer case to shut off the front wheel axle?
Ford Ranger / B-Series :: 1986 - Stalls When Hot / Won't Restart Until Cool
I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:
-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap
I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.
Ford Ranger / B-Series :: 1988 - No Crank / Whizzing Noise / Starter Is Spinning But Not Engaging
My 88 2.3l 5 speed ranger was running fine then i went to start it up again and it wouldn't turn any of the cylinders or none of the belts move. i can hear the fuel pump turn on for about a second every time, there is weak fuel pressure at the rail. Why wouldn't the engine crank? the starter does not turn the belts and all i hear is a whizzing sound. it sounds as if the starter is spinning but not engaging.
I have had problems with the fuel pump relays but those are all taped up pretty good. I am leaning towards a clogged fuel filter or bad fuel pump. but even with a bad fuel pump or clogged filter wouldn't the engine try to crank even with low fuel pressure? I have a new battery in there. I checked all the fuses in the kick panel. I will check the inertia switch wires as the inertia switch has been disabled.
Ford Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord Ranger / B-Series :: 1986 - No Fuel To Rail / Truck Quit On The Way
I have a 86 ranger 2.9 5 speed. A few days a go I replaced the front fuel filter and all seemed ok. Last night on my way home the truck quit and I had to have it towed home. Now I find both pumps don't seem to be working. What would make me loose both pumps??
View 11 RepliesFord Ranger / B-Series :: 1986 - Fuel System Wiring Diagrams?
Looking for the wiring diagrams for 86 ranger fuel system. I replaced the fuel pump relay after testing and finding that it was bad, still not getting fuel. I want to test any fusible links or anything else that could have gone wrong before I throw another part at it.
View 1 RepliesFord Ranger / B-Series :: 1986 - Brake Light Fuse Keeps Blowing
I've got an 86 ranger sport and I'm having trouble with the lights. The turn signals work, and ALL 4 bulbs in the back are new. The brake light fuse keeps blowing, and the fuse for the tail lights is good but they won't come on at all. I was told there was a direct short somewhere, does that sound about right? And is there a common place where they tend to short out?
View 2 RepliesFord Ranger / B-Series :: 1992 - Hesitation / Starts Spinning Tires Under Full Throttle From A Dead Stop
So among the other annoyances my 92 Ranger 4.0 auto has it has a hesitation before it starts spinning the tires under full throttle from a dead stop. It's the 4.0 automatic. I thought it would have more power than it actually does being use to a 2.5 auto. But this 92 4.0 runs and drives good. I've gotten it tuned up with new motorcraft wires, plugs, new coil, fuel filter, fuel pump assembly, fuel pressure regulator, air filter, idle air valve, new O2 sensor, new Dynomax muffler. I can't find any vacuum leaks. The engine idles slightly rough after you start it up from it sitting for a few hours, but quickly smooths out as soon as you start driving it.
This one here has no EGR. Transmission feels good, may have even been replaced by previous owner before we got it. It shifts good and the fluid is clean and the transmission is the cleanest part under the whole truck. No way of knowing for sure. The truck currently has 111,000 miles and I did all that stuff when we got it at 101,000 miles. So what could it be? I'm thinking a lazy injector or could it be the catalytic converter? Or could it be the throttle body? I know I once had a BBK throttle body on it and it made the world of difference in off the line power but it kept throwing too rich/lean condition and a TPS code so I had to return it. It sucks because it did wake up the motor. I returned it and since then the Check Engine Light hasn't come back on.
Ford Ranger / B-Series :: 1986 - Diesel Swap - Engine And Trans Combos?
I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.
View 14 RepliesFord Ranger / B-Series :: 1986 2WD Not Running - Shift Linkage In Way To Change Starter?
But here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.
View 1 Replies