Ford Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Ford Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesFord Ranger / B-Series :: 2000 / 4R44e Transmission - Hard Shift From 2 - 3 Gear
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 RepliesFord Ranger / B-Series :: 2003 - Hard To Shift After It Warms Up
I bought a 2003 Ford Ranger, 2.3, 5 speed manual. It is hard to shift after it warms up. I test drove it when it was below freezing, so I didn't notice it at first. The warmer the day and quicker the truck warms up, the worse it is. It goes into gear with no problem when the engine is off or if I'm still moving, but if I'm stopped there are times it is hard to get into gear. This really sounded like a clutch that wasn't fully disengaging to me, so I decided to pull it apart. I didn't check the movement at the slave before I started, but I did find the master was a little wet at the rod in the cab.
So, I did the following:
- New clutch master cylinder (system bled out of truck to eliminate air)
- New slave cylinder and bearing
- New pilot bearing
- Changed transmission fluid - Mercon III ATF
I inspected the clutch/pressure plate and it was in good shape and looked like it might have had 10K - 20K miles on it. The last owner said it was recently replaced and it looked it. So, I put it back in. After I was done, I checked the movement at the slave/pressure plate and it is moving about 3/8" - 1/2" when the pedal is down. I was happy and thought this would solve the problem since the old pilot bearing seemed stiff and I saw the leak on the back of the master cylinder.
I drove it and all felt fine at first, but it was a cool day and I didn't drive it that long. When it was warmer over the next couple of days, it started getting hard to shift again. It's not been quite as bad as before, but still doesn't shift right.
Ford Ranger / B-Series :: 1999 XLT V6 - No Clutch / Can't Shift
When I got home today I went to back into my parking spot and couldn't get my truck in reverse, or any other gear for that matter.
I've been suspecting something was going to go wrong because the last few weeks or so when I push the clutch in it sounded like bb's rolling around in a metal coffee can. Since I have owned it (2 yrs) the clutch has seemed funny anyhow, as in I really have to feather it so it doesn't grab and stall out.
So I've visually inspected what I can so far. Master cylinder fluid is at a proper level and I pulled the inspection cover on the transmission. I didn't see any fluid and reached inside and there wasn't residue in there either. I observed the throwout bearing pushing the clutch cover fingers in when the pedal is pressed and that is about it.
Just wondering about some additional checks I can perform to pinpoint the problem, as well as how to fix it and get rolling again.
1999 Ford Ranger 4x4 XLT
3.0 V6
134,xxx miles
No modifications
Ford Ranger / B-Series :: 1998 - How Hard Is It To Replace A Clutch
I think the time is near for a new clutch in my 98 Ranger, 2wd/ 5 spd. How tough of a job is this? I've changed the one in my 66 Mustang years ago but things were less complicated then.
View 3 RepliesFord Ranger / B-Series :: 2000 - 4WD Hard To Shift
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 RepliesFord Ranger / B-Series :: 1997 - Clutch Pedal Hard And Could Not Depress It
This is unusual. After driving into town for new tires, the clutch pedal was hard and I could not depress it after the tire tech parked the truck. It did finally depress with a pop, though the pedal functioned there after the clutch did not function properly.
At times it seemed to be ok at other times it seemed weak. I stopped by Autozone and checked the fluid, seemed low and I added some. Continued home not completely confident that I would make it. Had to make one stop along the way.
Once again the clutch pedal was stuck at the top and would not depress. I finally slid the safety switch up the clutch shaft to start the truck, when the engine started the pedal depressed. I was able to continue home but the clutch is not functioning properly.
Ford Ranger / B-Series :: 2004 - Hard To Shift Into Low Gear
It's a 4 cylinder 5 speed, and once or twice a day when the light turns green and I go to put it in low gear, it just doesn't want to go into gear easy. It's like the syncro isn't happy or something. The clutch is depressed all the way and not dragging.
View 14 RepliesFord Ranger / B-Series :: 2002 - Hard To Shift Gears
I have a 2002 ford ranger edge. swb, 3.0L, 5spd. I have been noticing it is getting harder to shift gears, put in 1st at a stop light lately. There is no grinding just seems harder to engage. Checked fluid level and it is clean and full. Recently i have developed a vibration under power. Let off the gas and smooth as can be, apply throttle and starts vibrating. Not sure if flywheel is "hot spotted" or perhaps broke a spring on pressure disk. Just seems odd it's only under throttle. Yes already checked rear end and U-joints.
View 2 RepliesFord Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesFord Ranger / B-Series :: 1999 - Hard To Shift Smoothly Into Third Gear
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 RepliesFord Ranger / B-Series :: OD Off Light Flashing - Hard To Shift In 2nd And When Downshift
I have a 99 Ranger, 3.0 xlt 2WD Automatic 5r55e(???) tranny (i know its the 5). I have the o/d off light flashing. It comes on when fluid gets to op temp. When on it shifts hard into 2nd and hard when it downshifts. No slipping. I have had the truck in the tranny shop for 3 weeks, owner said he re built valve body gasket (didnt work) tried 3 diff used tranny's (didn't work) or so he says. He said it needs to be rebuilt.
I have searched up and down for what it could be, there is so much out there, it only confused me more. If i have to rebuild i will, i think the tranny shop was pulling my leg (for more reasons than mentioned). I have a check engine light on nothing to do with tranny...there is a tranny code, he would not tell me but i will have it checked. Been told could be throttle position sensorl, speed sensor cracked case and a million other things. I have some mechanical abilities, (not too much w/ tranny's) but i can change a few simple sensors.
Ford Ranger / B-Series :: Column Shifter Too Hard To Shift Through Gears?
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
Ford Ranger / B-Series :: Shifting Hard / Clutch Won't Disengage At All After Master Cylinder Replaced
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
Ford Ranger / B-Series :: 1989 Truck Jerked Really Hard - Lurch When Clutch All The Way Pushed Down
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
Ford Ranger / B-Series :: 1997 - Transmission And Clutch Interchange
Will a clutch/flywheel and 5 spd from a 1997 ranger bolt up to an older 1980ish engine that had a 4 spd? What about the starter?
View 1 RepliesFord Ranger / B-Series :: 1992 - No AC And Power Steering / Poor Clutch Disengagement Resulting Hard Shifting
1992 Ford Ranger 4x2 with 2.3L engine and 5 speed manual transmission. 135,000 miles, no AC and no power steering. I am having poor clutch disengagement and resulting hard shifting. The shop added a little fluid to the reservoir last oil change and it is still looking full. I always park on concrete and never see any leaking. I don't know what may have been done before as I haven't had the pickup all that long. Where should I start? Is there probably internal bypass leaking in the hydraulic clutch as there seems to be no external leaking?
View 4 RepliesFord Ranger / B-Series :: 2008 - Transmission Becomes Very Difficult To Shift / Seems To Be Holding Air
My son has a 2008 Ranger 4.0 4wd 5 speed. Every month or so we need to bleed the clutch as the transmission becomes very difficult to shift. It does not lose fluid, but seems to be holding air. And it's not easy to bleed this setup. Slave going bad? I guess the transmission will need to come out then.
View 3 Replies