Ford F-150 (2009-2014) :: 2011 - Wrench Light On With P0720 Code?
I'm having issues when shifting into reverse and I it goes into limp mode when the wrench light shows up. This will not happen when shifting into Drive. When in limp mode I get engine code P0720. This calls for a bad Output Speed Sensor and my research says the sensor is on the back of the transmission but I cannot find any sensors on the transmission. there are several connectors clipped to it but I don't see any bolted in sensors. Also I cannot find a replacement sensor anywhere so I'm wondering if this is a generic code.
View 3 RepliesFord F-150 (2009-2014) :: Wrench Light On Upon Starting And Trying To Put It Into Gear - Code P0720
The last few days I've started getting the Wrench Light on my dash panel upon starting the truck and trying to put it into gear. I first noticed this on a cold morning and got the wrench but the truck went into Reverse and once I got going I was only in 3rd gear. I started and stopped the engine a few times and finally got it going. Since then it seems to do it all the time whether hot or cold. Tonight I noticed that if i start the engine and just go directly into Drive. I don't have the issue but if I ever go into Reverse it goes into limp mode and i get the big yellow wrench again. I only have engine Code P0720 which seems to refer to a speed sensor. I can't seem to find the sensor listed on the typical auto part websites.
View 4 RepliesFord F-150 (2009-2014) :: 2011 - Wrench Signal Showing On Instrument Cluster / Speedometer Will Go To 0
Town and all shops nearby have a week wait to get the truck in there. This happened once or twice a year ago but I'd pull over, shut it off and when I restarted it everything was fine. I'll be driving and all of a sudden the information display on the cluster will show a wrench signaling something's wrong(see image), then the speedometer will go to 0 and all information in center display will show flat lines. This started up yesterday but is now doing it after about 10min of driving every time I being driving. What's worse is the truck will randomly start shifting or shift extremely hard even when driving at a consistent speed. This was taken while truck was going about 45, but shows 0...
View 5 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On Pulling Even A Light Load Up A Grade
The thing is the truck seems to run fine. But, when it hits 30 pounds of boost it goes in to limp mode. Good way to get yourself run over on a highway. I'm wondering if the computer or whatever has gotten off somehow and is sensing a problem too early ? Would a re-flash possibly correct this ? BTW, it is a 2005 with 63,000 miles.
View 4 RepliesFord - Explorer :: 2006 - Wrench Light Came On
I was installing a neutral saftey tow light under the dash of my 06 sport trac. I touched one of the two wire to ground and wrench light came on. I checked fuse #18 and it was good. WHAT Did I do?...How do I fix it?
View 10 RepliesFord Escape / Hybrid :: 2010 - Wrench Light Come On
Drove about 200miles to see my daughter Saturday in college. Everything was ok I stopped for gas about 10 miles out of town on the highway then picked my daughter up for lunch. After we got back in the Escape and drove a few miles the wrench light come on and I lost power so I slowed and restarted it.
Everything work fine but I looked it up in the book and it said get it to service if this happens but hey it late Saturday and all in small towns were closed! After the college football game at about 9pm we left to go home on the highway just about 3-5 miles out of town it did it again lost power slowed then I restarted it ! Wrench light or power lost never came back on for the next 200 miles home! Could it just have been bad gas doing this or does the wrench light means big problems!
Ford 6.0L Power Stroke Diesel :: Wrench Light Came On
This morning on my 15 min drive to work my wrench light came on. i don't get over 30mph the whole time. I tired to get the code before i shut the truck off with my sct livewire but it showed no codes with the light on. It didn't drive any different no loss of power. When i checked memory codes with our shops modis scanner nothing unusual came up besides the fuel circuit fault, which i know about the gauge cluster needs repaired every now and then i cant listen to the radio or roll down the windows.
All my numbers on my livewire looked normal. This is the first time it's come on since ive had the over boost issue fixed. What it could be. Kinda of a kick in the pants after i just saved myself a few hundred on wheel bearings and ball joints. Had a grinding noise at different speeds. Couldn't find anything lose on the front end but still had a grinding noise. Ended up being the exhaust shifted and was rubbing up against the frame.
Ford - Explorer :: 2006 - Wrench Warning Light Came On
It's the first real rain of the season here in Northern CA and the "wrench" light came on as I was almost to work. I just get new transmission earlier this year, so I REALLY am trying NOT to spend a gazillion more on this car, but... It's our family's main mode of transportation (kids to school/picked up - long trips - daily 30 mile commute), we would like it running.
View 1 RepliesFord 6.0L Power Stroke Diesel :: EGR Failure - Wrench Light Comes On
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On But No Codes
Today on the way home after about 45 min drive my wrench light came on but when I checked for codes on my sct I get no codes. Is that weird or common?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Wrench Indicator Light Comes On Every So Often
6.0l oil cooler going - My wrench indicator light comes on every so often so I after about 40 min of highway driving. So I figured my oil cooler might be going out so here are my temps ....
View 8 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On - Small Oil Leak
I have a problem when I have been on the road for about an hour or more the wrench light comes on. There is no change in how the truck runs, and when I run a systems check it says that all of my temps are good to go. The one think I have noticed that the next morning I have a small oil leak on the ground on the days that the wrench has come on. The egr valve was just cleaned. I am getting ready to make a trip across the country with a 10,000 lb trailer so I am a little worried about this. Can I take it in to a shop and have them get a code when the light isn't on? Also I am replacing all of the glow plugs this weekend but from what I have read it shouldn't have anything to do with the wrench light.
View 9 RepliesFord 6.0L Power Stroke Diesel :: No Response When Hit The Gas Pedal / Wrench Light Came On
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 RepliesFord 6.0L Power Stroke Diesel :: Non Flashing Wrench Light On Dash
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
Ford F-150 (2004-2008) :: Shut Down To Idle / Wrench Light Came On - Code P2104
Well, truck did it again last night. Shut down to idle, wrench light came on. My Edge Insight showed P2104, Throttle Actuator Control System-Forced Idle. This is the third time it's done it over several months. Took it to Ford again, they didn't find anything. First time they replaced the throttle control unit. He's talking about RF interference but ignition & alternator checked ok. Each time it's done it has been in the same place, Sacramento Raceway. This is getting ridiculous, can't just drive it & show them because it's only done it over several months period.
View 14 RepliesFord F-150 (2004-2008) :: Wrench Light And Random High Idle After Driving?
I've got a 2006 F150 FX4 with a 5.4L 3V
A couple of months ago, I got a random "amber wrench light" on the dash. After I shut the vehicle off, it would go away. Over the last month, it's been coming back on more frequently....pretty near every time I drive the truck. I'm also noticing a bit of a dead spot in the pedal at times....though it's never failed me completely.
After a quick Google search, I was led to believe it could be a throttle body issue. Before replacing the throttle body, it was suggested to remove and clean the throttle body itself....which I did.
I'm still getting the amber wrench light, but now I'm also getting a random high idle after driving. If I throw it in park, it will idle up to 2,000RPM. I initially assumed I may have created a vacuum leak of some sort, but when I shut the engine off and restart it (or even blip the key off and on again quick before the engine dies, it comes back to life and idles fine? This tells me that it isn't a vacuum issue.
The strangest part, is that it's not tripping any codes what so ever?
Ford Super Duty (1999-2016) :: No Response From Accelerator / CEL And Wrench Light On
I have a 2005 F250 5.4L 2wd. Parked the vehicle in my driveway and the next morning there was no response from the accelerator and the CEL light and the wrench light on. I pulled the codes and came up with codes P2104, P2107 and P2110. The KOEO code was P2122. I checked the wiring and connectors and all appear to be fine I replaced the throttle body and no change. I removed the accelerator pedal and tried it on another vehicle and it worked fine. I have power to pin 16 on the diagnostic port. After clearing the codes and rescanning the same codes come up immediately.
View 14 RepliesFord F-150 (2004-2008) :: 2005 - Electronic Throttle Control / Wrench Light
2005 Ford F-150 FX4 5.4 V8
So my battery died the other day when I was working on the radio and I ended up having to jump start the vehicle. After the jump start the Wrench light came on the truck or the ETC light. (After doing research I have discovered you are not supposed to jump start a vehicle with ETC)
I have taken the car to the auto parts store and it does not seem the code readers they have can read codes for the ETC light.
I have also disconnected the battery cable to try and reset the light, but it still always comes on about 10 seconds after starting the car.
I have had no issues with the vehicle despite the light. No rough idle, no starting issues, or acceleration issues at any speed. What I can do to resolve this light or what part I fried when I jump started the car?
Ford - Explorer :: Check Engine Light And Wrench Symbol On With Multiple Codes
I have 2007 explorer 4.0 4x4. Check engine light and wrench symbol on with codes po743 po750 po755 po po765 po966 po966 po970. Feels like it is now stuck in 3rd gear.
View 2 Replies