Ford 6.0L Power Stroke Diesel :: Wrench Light Comes On Initially / Click Under Dash And Cab Lights Go Off
2006 F-250 6.0l,Auto, 175,xxx mi
When I turn the key to on, I hear the vacuum pump cycle (passenger side fender), but don't hear the glow plugs or injectors cycle. Glow plug light comes on and stays on for 30secs. Wrench light comes on initially, but goes off after 3 secs, but then comes back on after about 8-10 seconds. When the wrench light comes on, I hear a click under the dash and my cab lights go off.
When I turn the key to start, nothing happens. If I jump the starter, engine turns over, but doesn't start. I have check numerous fuses, disconnected the fan clutch, tried moving the shifting lever to neutral, wiggled wires around the FICM/PCM/GPCM with no success.
I tried checking for DTC codes, but my scanner (300 reader) doesn't get any power. I have checked my light, it has power.
Twice before, the truck failed to start like this, but after removing & inspecting fuses/relays (all were good), it started back up. Also, occasionally the truck would stall, (just like someone turned the key off), but would start right backup. But when it stalled, the glow plug light would illuminate for a second,then go off.
Own truck for 8 months, replaced the batteries & injectors 6 months ago. Very light puff of smoke when starting up otherwise ran well when shut off.
How to proceed? My first diesel so I may need some extra details.
Ford 6.0L Power Stroke Diesel :: Wrench Light Came On
This morning on my 15 min drive to work my wrench light came on. i don't get over 30mph the whole time. I tired to get the code before i shut the truck off with my sct livewire but it showed no codes with the light on. It didn't drive any different no loss of power. When i checked memory codes with our shops modis scanner nothing unusual came up besides the fuel circuit fault, which i know about the gauge cluster needs repaired every now and then i cant listen to the radio or roll down the windows.
All my numbers on my livewire looked normal. This is the first time it's come on since ive had the over boost issue fixed. What it could be. Kinda of a kick in the pants after i just saved myself a few hundred on wheel bearings and ball joints. Had a grinding noise at different speeds. Couldn't find anything lose on the front end but still had a grinding noise. Ended up being the exhaust shifted and was rubbing up against the frame.
Ford 6.0L Power Stroke Diesel :: EGR Failure - Wrench Light Comes On
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On But No Codes
Today on the way home after about 45 min drive my wrench light came on but when I checked for codes on my sct I get no codes. Is that weird or common?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Wrench Indicator Light Comes On Every So Often
6.0l oil cooler going - My wrench indicator light comes on every so often so I after about 40 min of highway driving. So I figured my oil cooler might be going out so here are my temps ....
View 8 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On - Small Oil Leak
I have a problem when I have been on the road for about an hour or more the wrench light comes on. There is no change in how the truck runs, and when I run a systems check it says that all of my temps are good to go. The one think I have noticed that the next morning I have a small oil leak on the ground on the days that the wrench has come on. The egr valve was just cleaned. I am getting ready to make a trip across the country with a 10,000 lb trailer so I am a little worried about this. Can I take it in to a shop and have them get a code when the light isn't on? Also I am replacing all of the glow plugs this weekend but from what I have read it shouldn't have anything to do with the wrench light.
View 9 RepliesFord 6.0L Power Stroke Diesel :: No Response When Hit The Gas Pedal / Wrench Light Came On
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On Pulling Even A Light Load Up A Grade
The thing is the truck seems to run fine. But, when it hits 30 pounds of boost it goes in to limp mode. Good way to get yourself run over on a highway. I'm wondering if the computer or whatever has gotten off somehow and is sensing a problem too early ? Would a re-flash possibly correct this ? BTW, it is a 2005 with 63,000 miles.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Wrench Light Keeps Coming On Mostly When Doing Highway Driving
I have ran 05 f250 and the wrench light keeps coming on mostly when I'm doing highway driving or when I go to pass someone. iv putt code readers on it(autoparts store readers and the good expensive ones)and i keep getting bad egr and some other codes but when I have the truck looked at everything is prefect I had a flush done on the truck and and it still comes on randomly . Could the fact that it needs an oil change cause the light to come on intermittently or is something else going on??
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Wrench Light Came On While Driving On The Highway
2007 f250 6.0 .... I just had the wrench light come on while driving on the hwy. wasn't towing, or hauling anything. Just traveling around 70mph for an hour or so. I didn't notice any change in power. Got to my destination and cut the engine off. Couldn't pull any codes with an OBD II scanner. When I started it up again, light was gone. Owner's manual points to electronic throttle control, not much else.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Gage Fault And Tow Haul Flashing On Dash?
Have a Gage fault and tow haul flashing on the dash have no clue what is going on?
View 8 RepliesFord 6.7L Power Stroke Diesel :: 2013 - Dash Lights Flashing / No Restart After Shut Off
6.7 with 19k . Drove about 2 miles and noticed dash lights were flashing and ac was not working correctly . Pulled into garage shut off and truck wouldn't restart, no crank ! All my dash lights were flashing & dash was giving numerous messages.. At least I wasn't on my road trip 2 weeks ago! 3400 mile round trip. Truck was towed to dealer! My 6.0 never left me stranded & I had 3 of them..
View 14 RepliesFord 6.0L Power Stroke Diesel :: Size Of Wrench For Battery Terminal?
I'm not near my stuff--is the battery cable terminal bolt 8mm?
View 14 RepliesFord 6.0L Power Stroke Diesel :: ABS Light Goes On / Flashing TowHaul With CEL?
Okay I have a 2007 F350 crew cab powerstroke dually that is totally stock and motor has 32k/cab has 130k. She normally runs perfect, I've replace the unison ring in the turbo, one fuel injector was replace, the EBP sensor was, cleaned the EBP tube was cleaned, EGR stuff is newish, new altenator and upper motor was cleaned of all the carbon. All of that was done in last 6 months and I use Rotella T6 with OEM filter. So this morning I start her up just fine and go to get coffee, when I'm leaving my ABS light goes on. I pull over to shut her off then restart and ABS light goes away.
I drive for 15 minutes go inside this office for 10-15 minutes then get back in my truck and leave. While I'M driving I hear this slight tingling every so often, like something is touching the brake dust shield on my L/F wheel. I fill her up with diesel then leave gas station to have my TowHaul light start flashing with a lit engine light. I scan with my scan gauge 2 and get P000, I've read the P000 means there are no diagnostic trouble codes. All the temps were within spec, she was still running gd, shifting gd and braking gd. The flashing towhaul light is a transmission issue rt, so if that's flashing there should have been a DTC besides the P000. Then the ABS light going on earlier is not a coincidence ...
Ford 6.0L Power Stroke Diesel :: 2003 - Download SCT Livewire Now No Power - Theft Light Flashing?
I have an 03 excursions with 6.0. I downloaded the sct livewire ts and the problem started. Through truck has no power the thief light flashes codes for cam and crank sensor and on when it acts up the glow plug light comes on. On the on the ts monitor it says no key in the ignition.
View 11 RepliesFord 6.7L Power Stroke Diesel :: Wrench Icon Displaying In The Instrument Panel - Communication Codes
Couple of weeks ago, the display in the instrument panel displayed a large orange wrench. No accompanying text or chimes, just the damn wrench. Checked for codes, nothing out of the ordinary (I occasionally get communication codes, but they usually show up when I do not wait to start). Long story short, the damn thing showed up one more time the same day, then never again.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Check Gauge Light Coming On And Tow Haul Light Flashing
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Check Gauge Light Came On And Tow Haul Light Started Flashing
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
Ford 6.0L Power Stroke Diesel :: Tow / Haul Light Comes On Flashing At Random Times
My co-worker has an 06 F250 SC 4x4 and is getting a P0713 code. 2006 Ford F250 6.0L Diesel ... Tow/haul light comes on flashing at random times. Truck is reading a P0713 code which is the TFT Sensor Failure/Replacement
Ford dealership is telling me that I also have to pull the valve body and install the new upgraded wiring harness (3-3.5 hours labor) but a thread on this forum stated I just needed to replace the sensor in the tranny pan and reconnect the wire harness. Do I need to upgrade the wiring harness?