Ford - Explorer :: 2006 - Wrench Light Came On
I was installing a neutral saftey tow light under the dash of my 06 sport trac. I touched one of the two wire to ground and wrench light came on. I checked fuse #18 and it was good. WHAT Did I do?...How do I fix it?
View 10 RepliesFord - Explorer :: Check Engine Light And Wrench Symbol On With Multiple Codes
I have 2007 explorer 4.0 4x4. Check engine light and wrench symbol on with codes po743 po750 po755 po po765 po966 po966 po970. Feels like it is now stuck in 3rd gear.
View 2 RepliesFord - Explorer :: 2007 - ABS / Traction Control And Wrench Lights All Come On
A few days ago my wife's 07' explorer 4.0L, 4wd, 72k miles, had the abs light, traction control light, and a wrench light all come on. By the the time I got to look at it, they were off. Now 3 days later, they have all come back on. To me it seems like a electrical issue or maybe a sensor or something but I wanted to get your thoughts on where to start looking.
View 7 RepliesFord - Explorer :: 2004 - Limp Mode After Going About A Mile / Orange Wrench Symbol And Die
2004 Explorer Eddie Bauer . Bought it like this and trying to figure why. Code is P0740 and P0743. It will go about a mile then go into Limp Mode with the Orange Wrench symbol and will die. If I pull over and restart it will go another mile before doing it again. Any Tips? Trans is 5R55S....
View 2 RepliesFord - Explorer :: ABS/ RSC Warning Light On?
diagnose what is tripping the warning light for the ABS/RSC system. We have a 2008 Explorer, 2-wheel drive, with the V8 engine. It has just over 16,000 mile on it.
Intermittently, when we hit the brakes, there is a slight sensation of jerking and roughness. The ABS RSC warning light and beeping occurs on occasion as well. If I go really easy on the brakes, all is well.
I have removed and inspected all brake pads. They look fine; so do the rotors. I have also inflated the tires so that they are perfectly equal.
I'm not sure how the RSC system is supposed to operate. I suspect that a sensor is relaying that the system should be activated, which causes the brakes to perform differently and the alarm to go sound. Both the ABS and the RSC warning lights turn on. I'm guessing that I may have a bad sensor somewhere, but I don't know where they are or how to test them.
Ford 6.0L Power Stroke Diesel :: Wrench Light Comes On Pulling Even A Light Load Up A Grade
The thing is the truck seems to run fine. But, when it hits 30 pounds of boost it goes in to limp mode. Good way to get yourself run over on a highway. I'm wondering if the computer or whatever has gotten off somehow and is sensing a problem too early ? Would a re-flash possibly correct this ? BTW, it is a 2005 with 63,000 miles.
View 4 RepliesFord - Explorer :: 2007 XLT - Door Ajar Warning And Dome Light Comes On While Driving
2007 ford explorer xlt door ajar warning and dome light comes on while driving also dome light comes on while parked for no reason...
View 9 RepliesFord F-150 (2009-2014) :: Wrench Light Came On - Only 12 MPG?
My 09 F150 Platinum 4x2 used to get 15 mpg city regularly. One day while driving the wrench light popped up and i was in limp mode. I parked the truck and went to my scheduled squadron PT like a good troop is supposed to do. Anyway, finished and the truck has been fine, Ford dealer finds no issues at all with it. My gripe is now i get 12 MPG since the issue and I told them my MPG has gotten worse since it happened. What it could be?
View 1 RepliesFord Escape / Hybrid :: 2010 - Wrench Light Come On
Drove about 200miles to see my daughter Saturday in college. Everything was ok I stopped for gas about 10 miles out of town on the highway then picked my daughter up for lunch. After we got back in the Escape and drove a few miles the wrench light come on and I lost power so I slowed and restarted it.
Everything work fine but I looked it up in the book and it said get it to service if this happens but hey it late Saturday and all in small towns were closed! After the college football game at about 9pm we left to go home on the highway just about 3-5 miles out of town it did it again lost power slowed then I restarted it ! Wrench light or power lost never came back on for the next 200 miles home! Could it just have been bad gas doing this or does the wrench light means big problems!
Ford 6.0L Power Stroke Diesel :: Wrench Light Came On
This morning on my 15 min drive to work my wrench light came on. i don't get over 30mph the whole time. I tired to get the code before i shut the truck off with my sct livewire but it showed no codes with the light on. It didn't drive any different no loss of power. When i checked memory codes with our shops modis scanner nothing unusual came up besides the fuel circuit fault, which i know about the gauge cluster needs repaired every now and then i cant listen to the radio or roll down the windows.
All my numbers on my livewire looked normal. This is the first time it's come on since ive had the over boost issue fixed. What it could be. Kinda of a kick in the pants after i just saved myself a few hundred on wheel bearings and ball joints. Had a grinding noise at different speeds. Couldn't find anything lose on the front end but still had a grinding noise. Ended up being the exhaust shifted and was rubbing up against the frame.
Ford 6.0L Power Stroke Diesel :: EGR Failure - Wrench Light Comes On
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On But No Codes
Today on the way home after about 45 min drive my wrench light came on but when I checked for codes on my sct I get no codes. Is that weird or common?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Wrench Indicator Light Comes On Every So Often
6.0l oil cooler going - My wrench indicator light comes on every so often so I after about 40 min of highway driving. So I figured my oil cooler might be going out so here are my temps ....
View 8 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On - Small Oil Leak
I have a problem when I have been on the road for about an hour or more the wrench light comes on. There is no change in how the truck runs, and when I run a systems check it says that all of my temps are good to go. The one think I have noticed that the next morning I have a small oil leak on the ground on the days that the wrench has come on. The egr valve was just cleaned. I am getting ready to make a trip across the country with a 10,000 lb trailer so I am a little worried about this. Can I take it in to a shop and have them get a code when the light isn't on? Also I am replacing all of the glow plugs this weekend but from what I have read it shouldn't have anything to do with the wrench light.
View 9 RepliesFord 6.0L Power Stroke Diesel :: No Response When Hit The Gas Pedal / Wrench Light Came On
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 RepliesFord 6.0L Power Stroke Diesel :: Non Flashing Wrench Light On Dash
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
Ford F-150 (2009-2014) :: 2011 - Wrench Light On With P0720 Code?
I'm having issues when shifting into reverse and I it goes into limp mode when the wrench light shows up. This will not happen when shifting into Drive. When in limp mode I get engine code P0720. This calls for a bad Output Speed Sensor and my research says the sensor is on the back of the transmission but I cannot find any sensors on the transmission. there are several connectors clipped to it but I don't see any bolted in sensors. Also I cannot find a replacement sensor anywhere so I'm wondering if this is a generic code.
View 3 RepliesFord F-150 (2004-2008) :: Shut Down To Idle / Wrench Light Came On - Code P2104
Well, truck did it again last night. Shut down to idle, wrench light came on. My Edge Insight showed P2104, Throttle Actuator Control System-Forced Idle. This is the third time it's done it over several months. Took it to Ford again, they didn't find anything. First time they replaced the throttle control unit. He's talking about RF interference but ignition & alternator checked ok. Each time it's done it has been in the same place, Sacramento Raceway. This is getting ridiculous, can't just drive it & show them because it's only done it over several months period.
View 14 RepliesFord F-150 (2004-2008) :: Wrench Light And Random High Idle After Driving?
I've got a 2006 F150 FX4 with a 5.4L 3V
A couple of months ago, I got a random "amber wrench light" on the dash. After I shut the vehicle off, it would go away. Over the last month, it's been coming back on more frequently....pretty near every time I drive the truck. I'm also noticing a bit of a dead spot in the pedal at times....though it's never failed me completely.
After a quick Google search, I was led to believe it could be a throttle body issue. Before replacing the throttle body, it was suggested to remove and clean the throttle body itself....which I did.
I'm still getting the amber wrench light, but now I'm also getting a random high idle after driving. If I throw it in park, it will idle up to 2,000RPM. I initially assumed I may have created a vacuum leak of some sort, but when I shut the engine off and restart it (or even blip the key off and on again quick before the engine dies, it comes back to life and idles fine? This tells me that it isn't a vacuum issue.
The strangest part, is that it's not tripping any codes what so ever?