Lexus RX 2004-09 :: Error Code P0015 / Camshaft Position - Timing Over Retarded (Bank 1)
A week ago I was traveling in my wife's 2009 RX350 at freeways speeds and outside ambient temperatures around 80 degrees. After traveling about 2 hours and stopping for about half-hour for lunch, I started the vehicle and went around a mile and the Check Engine light came on, the VSC was flashing and the traction control indicator was illuminated. I stopped quickly in a gas station and checked the manual for what the warning lights meant. Nothing of any value was found; I filled the car up and headed for home, about 4 more hours at highway speeds. The warning lights stayed on and the VSC flashed the entire way home. The vehicle ran perfectly with no problems at all.
The next morning I started the car and the lights were out. Still worried, I purchased an OBD2 scanner and pulled a P0015 code, Camshaft Position - Timing Over-Retarded (Bank 1). I erased the code and the car has been fine ever since. Finally to the question, is this something I need to worry about? I travel this trip about once a month and don't want to get stranded along the road. The car has 54K on it and if it is a sensor in the engine, it should be covered by the powertrain warranty, but more importantly, will it cause damage to the engine? I read that the camshaft position sensor would only be replaced under warranty if it was inspected and causing a loud ticking noise, which I do not hear. If it throws the same error code again, I will take it in to the dealer and let them look into it.
Golf IV / Jetta IV :: 2005 - Code P0011 Intake (A) Camshaft Position Timing / Over Advanced (Bank 1)
2005 GTI 1.8t Engine ... I changed my timing belt water pump and tensioner yesterday and today I am receiving an engine code: P0011 Intake (A) Camshaft Position Timing - Over Advanced (Bank 1) My friend timed the engine and knew that is was 1 tooth advanced. He told me that is was going to be OK because 1.8t's have a 1 tooth tolerance. I would have redone it but I did not know how. What to do in this situation? Do I need to re time the engine?
View 2 RepliesTouareg :: 2004 - CEL Code P0022 For Camshaft Position
My 2004 V8 touareg is throwing CEL code P0022. 'A' Camshaft Position - Timing Over-Retarded (Bank 2)
What would cause this? I found that these all could be related:
- Valve timing
- OCV
- Camshaft timing gear assy
- ECM
Would any of these cause it to burn oil more quickly? What steps are taken to diagnose the whole problem?
Ford F-150 (2004-2008) :: Code P0012 - Cam Timing Is Over Retarded
I have a 2004 F-150 FX4 and I am getting Code P0012 on an OBD II code reader. This is saying that the cam timing is over retarded. What is the best way to fix this?
View 5 RepliesSonata NF (2006-10) :: Got Engine Code P0022 - Oil Control Valve (Bank 2)
Got Engine Code P0022. Listed several things, Cam Position Indicator (replaced it) and CVVT Oil Control Valve Bank 2. Dealer calls them "front" and "rear". Is Bank 2 the rear (Black or gray also).
View 1 RepliesFord F-150 (2009-2014) :: Codes P0345 And P0349 - Camshaft Position Sensor Bank 2 Circulation Error / Interim
For 2009 and 2010 f150's with the 5.4L engine, this may apply to you.
About a month back I got some odd vibrations at start-up and while driving and the following codes:
P0345 - Camshaft Position Sensor, Bank 2 (drivers side), circulation error
P0349 - Camshaft position Sensor, Bank 2 (drivers side), circulation Interim.
These codes are common in the previous generation truck for various reasons. In my case, I started trying to troubleshoot with the easiest solutions first.
Checked the battery - fully charged.
Checked/played with the alternator connection and related wiring - looked good.
Checked the oil - it was down at the half mark on the dipstick, so toped it off with synthetic oil.
Cleared the codes, and now have been driving for a month, no issues, no codes!
If these codes come up for other folks, try the easiest on the list first, before bringing to the dealer... these codes can be really hard to solve, but sometimes we can get lucky.
Ford F-150 (2004-2008) :: Slight Ticking Noise - Code P0022
Getting code P0022, which is over retarded cam position, drivers side bank. My 2004 F150 has the 5.8 triton. I have replaced all cam phasers and tensioner a as well as the timing chains. I have also replaced both VCT solenoids. Before I was getting codes for both banks, now just the code mentioned above with a slight ticking as well. My question is this... What am I not seeing? What could be causing this?? Would it be beneficial t get the lockout kit for the phasers to always keep them open?? Seems to stall a little at very low RPM like when you are off-road.
View 1 RepliesFord Super Duty (1999-2016) :: P0014 - Exhaust Camshaft Position Timing
Seems like a real problem and not just emissions related. The truck seems to run fine; no abnormal vibration.
Seeing the dealer on wednesday and was supposed to leave for a 2 month trip on sunday.
Bad to go sunday anyway and wait for a dealer on the road?
How likely is it that the dealer will have this fixed on wednesday same day?
Ford F-150 (2004-2008) :: Running Rough Loud And Dies - P0022 Cam Sensor Code
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 RepliesGolf IV / Jetta IV :: 2004 - Camshaft Position Sensor Error Code
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
Ford F-150 (2004-2008) :: 2005 - Rough Idle At Low Speeds Primarily In Reverse / Code P0022
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
Ford F-150 - 1997-2003 :: Code P0340 - Cam Position / Bank 1?
The p0340 code is the cam position right? Ready says bank 1.. Is there 2? Where the bank one is? And do I need to get on tdc on cyl one first or not?
View 3 RepliesFord - Explorer :: 1996 - Check Engine Light Code P0340 - Camshaft Position Sensor
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 RepliesFord F-150 (2004-2008) :: Check Engine Light Code Says Catalyst Deficiency Bank 2
I have a 2006 F-150 with the 5.4L. I got the check engine light and the computer says catalyst deficiency bank 2. So I assume the passenger side converter is blocked. Is there anyway to either take out the cat and replace with a piece of straight pipe and bypass the o2 sensors or take the cat out of the housing and put the housing in and then bypass the o2 sensors.
View 14 RepliesAccent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesElantra XD (2001-06) :: 2003 - CEL Code / Bad Camshaft Position Sensor
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
Accent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesCelica :: 1997 7afe 1.8 ST - P0340 Code For Camshaft Position Sensor
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesJimmy :: 95 Running Rough / Stuttering - Camshaft Position Sensor Code
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 Replies