Ford F-150 (2004-2008) :: F250 VVT Making Noise When Warm - Both Cam Position Sensor Codes
2008 Ford F-250 5.4L VVT. Setting both cam position sensor codes and both VVT PO12 and PO22 Codes. Runs good for a few minutes cold then goes to making noise and retards timing when warms up . Replaced both cam phasers and 1 vct solenoid and camshaft position sensors, changed oil and filter with motorcraft.. Tried unplugging VCT solenoids but still runs bad when warms up. Ran bad when engine was cold or hot before replaced phasers now only when warms up. Is it a oil pressure problem pressure shows good on dash gauge.
View 8 RepliesFord Super Duty (1999-2016) :: 2008 F250 V10 Missing / Dead / No Power And Multiple Codes
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 Superduty Six Liter
So looking for some thoughts on my truck.I'm looking at a Ford F350 up grade.What the problem is my 03 250 extra cab has 107,000 on it and all regular maintenance.If I trade it in I'm going to need a 5 gal pail of Vaseline to make a deal.The trade will reduce the sales tax on the new truck. I live in a rural area so selling out right could take a bit.It's paid for.
So your thoughts are welcome.
Thanks Mike
Ford F-150 (2004-2008) :: Missing With No Codes / Increases With RPM
I've developed a miss no codes mild at idle horrible at 70 mph 2100 rpms driven me nuts cant figure it out cops are good just put in new plugs & gonna swap them out for a new set they were motorcraft. Sprayed water on lines & intake looking for vacuum leaks but no change....
View 7 RepliesFord F-150 (2004-2008) :: Turns Over But Won't Start - No Codes
So, my 2004 FX ran perfect as always when I parked it last night but this morning it just will not start. It turns over like a SOB but won't catch (Installed a new Optima Red Top about a month ago). Tried my OBDII but it's showing as "fail" or "no codes".....I tried testing it several times. I've never had ANY problems with it starting.
View 2 RepliesFord Brakes/Suspension :: 1989 Superduty - Brake Line On Passenger Side Went Bad
The brake line on the passengers side went bad. Called ford for replacement and they said ford is not supplying that line any more. Where I can get a replacement? Its hard line and connects to the rubber line.
View 2 RepliesFord F-150 (2004-2008) :: Miss At Idle - Got Codes P0351 / 356?
I bought a 04 FX-4 a couple months ago with 102k on it. Brought it back to selling dealer, they replaced #1/#6 coils, its ran great till this past week. Again it has stumbled a couple times this week. It only seems to have the miss at idle (comes and goes) take off from light, within 50 feet its running like a champ again. I cleared the codes (disconnect battery)and now it seems my idle is not steady, it fluctuates. Is the idle a product of the codes?
View 2 RepliesFord F-150 (2004-2008) :: Shaking And Sputtering / Throwing CEL Codes
I have an '05 5.4L 3V and I was way to trusting in how it was running. BTW, I change the oil every 3 to 5 and have only driven highway miles, albeit a lot of them...155k! I bought it with 40k on it but was not aware of the plug change issue until I heard about it off-hand. I let the plug change go cuz it was running so well. Bad move.
Anyways, a few weeks ago it began to lose power and I suspected that the PCM was retarding the timing for some reason. Before I could get to the shop, the thing went nuts on me at 75mph. Started shaking and sputtering and throwing cel codes. I shut it down and after 5 minutes re-started. It seemed fine and actually was running a bit better. Took it in and the code was the 0302. #2 cyl misfire.
They also said the compression was very low on that cylinder and slightly low on 1,3 and 7 as well. I had them change the plugs and the #2 COP even though they said I needed a new engine and then I picked it up. Now the engine barely runs at all. It shakes violently, where to go from here. What should I do now? New engine?
Ford F-150 (2004-2008) :: 2005 - Got Codes P0022 And P0345?
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
Ford F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesFord F-150 (2004-2008) :: Got Codes P0058 / P0138 / P2270?
I have a 2004 f150 5.4 with 78,000 miles and i have a engine light on so i had my bud do a scan and 3 codes came up P0058,P0138,andP2270 i was hopeing yall could explain the problem and point me in the direction to fixing this problem.
View 3 RepliesFord F-150 (2004-2008) :: 2006 V6 - Got Codes P0171 And P0302
I'm lost. Got P0171 and P0302 ... 2006 4.2 V6 5-speed 220K ... Got bad miss ...
Compression check was good.
Replaced plugs.
Replaced wires.
Replaced coil pack.
Cleaned MAF
Miss remains. What do I do next?
Ford F-150 (2004-2008) :: 5.4L - Getting Codes P0340 And P0344 Randomly?
At around 100K miles started to get the dreaded P0340 and P0344 that occurs randomly - engine cold, engine hot, rainy, hot, cold, you get the picture. Only occurs at startup. Shutdown/Clear Code/Restart and all is well for days... otherwise the engine runs fine. Have replaced the CMP sensors, thoroughly cleaned CMP and crankshaft sensor connectors, even replaced the alternator. I would like to tone out the wiring back to the PCM connector pins. I am trying to find a pinout diagram. PCM is 7L3A-12A650-GKF.
View 2 RepliesFord F-150 (2004-2008) :: Start / Run Rough For A Second Then Die - Codes P0172 And P0175
First off its a 2006 F150 king ranch with the intercooled roush kit and roush tune. Last couple weeks its progressed from a slight stumble on start up, to now after its been off for a few hours it may start and run rough for a second, or, it may start then die, and then have to crank for at least 5 seconds before it starts. After it starts it seems to run fine. I've thrown the P0172 and P0175 code a few times. I downloaded the torque android app and did some data logging. Can you learn anything from the long term fuel trim?
View 9 RepliesFord F-150 (2004-2008) :: Multiple Codes - Random Misfire Detected
I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
Ford F-150 (2004-2008) :: No Codes / Low Idle / High STFT And Load?
For the techs in here, I have a data logger (AutoTap) and the symptoms are low idle and sometimes it runs rough idling and driving. It had me thinking the fuel pump was going out. That is not the case. I did get into part swapping mode so I have new plugs and coils and new VCTs all in the last 24 hours. The engine has 85K miles on it (rebuilt ford long block), truck had 150K. I'm not sure what parts were replaced when the longblock was replaced but I'm guessing the 02's are original.
Data that looks odd to me in the Autotap real time data logging is this:
- STFT Bank 2, goes from 10-15% and climbs till its over 300% and then the truck goes into Open Loop due to an error (per the Autotap) but it never says what error and the CEL never lights. Idle goes up when its in open loop and then after a minute or two it will drop back into closed loop.
- Fuel pressure never drops below 37
- Idle will drop to 250rpm
- Engine load at idle is 25%?! With AC on and idling (at 550rpm) engine load is 42%? Seems high no?
Nothing else other than the STFT Bank 2 and the high engine load seems out of miss. No misfires, codes, etc. What else should I look at?
Other background/patient history:
- Alternator #3 was installed 2 weeks, It replaced alternator #2 that went in 4 months ago to replace the original alternator (144K miles). Both died and caused low voltage/battery dying symptoms and verified by volt meter.
- FPDM was replaced proactively 8 months ago just because I don't want it to break down when I'm towing my race car.
- I have not tried cleaning MAF, EGR?, IAC, nor have I replaced O2s. The only thing that leads me to believe MAF might need cleaning is the load?
Ford F-150 (2004-2008) :: Gode Codes P0172 / P0300 And P0303?
My son just left. We scanned his truck and got these codes.
P0172 Bank 1 rich P0300 random misfires P0303 cylinder 3 misfires.
I used the Torque APP Pro to check these codes. I went to live readings in the Torque APP and saw some readings for Long term and Short term bank 1 Readings.
They are all "greek" to me, and I don't recall what they were, but could get those readings tomorrow.
When I have done searches combining these codes together, I see changing spark plugs. P0172 alone gets me a different train of thought. Mainly CAT issues.
Also, his cranking to start is quite long. (A lot longer than my 6.0L would ever think of cranking) At least nearly 30 seconds of cranking. We are leaning toward first just changing #3 plug.
Ford F-150 (2004-2008) :: Got Codes P0174 / P0171 / P0345 And P0349?
My truck have 4 codes p0174 and p0171 system too lean bank 1 and bank 2, and p0345, p0349 camshaft position sensor bank 1 and bank 2.
View 3 RepliesFord F-150 (2004-2008) :: 2006 - Intermittent No Start Condition And No OBD Codes
2006 F150 4.2 fuel issue? I get an intermitent no start condition and no obd codes. Then I discover that it really isn't intermittent, it only occurs after I have been running the engine. It will not start for at least 5-10 minutes after I have driven a few miles and shut the engine off. So if I wait 5-10 minutes then she starts and runs just fine. I played with this in the driveway to recreate this condition so I could determine if I had a spark or fuel issue (I have spark during no start). I found that 50% of the time I could start it right back up immediately after I shut the engine off. But if I shut it off right away again, then I got the no start condition again and have to wait another 5-10 minutes.
Now with cold engine I can start the motor over and over. To fix this I read forum after forum, which led me to decide that I had a fuel pump driver problem (module) located on back axle under spare tire. I replaced this and restarted the engine many times. The problem seemed to be gone but this only lasted about 30 minutes. Then it would not start at all and still no codes. I plugged my old module back in and the truck fired right up. So I decided I needed to (flash) pcm for new part but that changes nothing. Still no start with new module and runs with old module. I also replaced relay in fuse panel.