Ford Excursion :: Sputtering And Chugging - Throwing Many Codes?
I have had a wet weather issue twice, once last fall and once this spring. Both times were very wet and damp conditions causing a sputtering and chugging and dying at lights, both times no codes and after drying out in brother's shop it went away. Now this weekend up at the cabin it reappeared, again very wet conditions. Replaced the MAF...no change. Sputtered and chugged my way home with it killing at most stop signs/lights. Finally got home and couldn't even back the TT up the driveway, it would kill. Finally threw numerous codes (misfire in cylinders 1 and 9, and misfire in first 1000 revolutions). I'm thinking COPs as the plugs are not that old and the little research I have had time to do suggests this also. If it is COPs, I have heard there are some to avoid and some that are recommended?
View 9 RepliesFord F-150 (2004-2008) :: 2006 - Intermittent Misfire But Not Throwing Any Codes
I have a 2006 Lincoln Mark LT that seems to have an intermittent misfire. The truck is not throwing any codes either.
View 6 RepliesFord F-150 (2004-2008) :: 2007 - Throwing Codes P0012 / P0022 And P0345
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 - No Power / Throwing Codes P2196 And P2198
2008, 5.4 liter, F250, with 6-speed manual transmission
My truck was running fine until I decided to clean my engine. I just wanted to remove the extra dust covering it, so I used a low pressure garden hose to wash away the dirt that had accumulated last winter and spring.
It started throwing codes like Fuel Rail pressure sensors, P0191, P0192. I had no power, and I could hardly drive the truck.
I figured I had some water in some connectors, so I checked around, but could not detect any moisture.
I kept driving it, and the problem got less severe. One warm summer day, I drove my truck for about an hour trip, and everything looked fine after this. Problem never came back.
I was even noticing that it was better on gas that ever before, I was doing 11liters/100km, in city driving.
Until one day (2 months later), I had to disconnect the battery to do some servicing on my truck (more that 30 minutes), and it started to run crappy again, having some piston misfire, throwing codes P2198 and P2196, (O2 sensors). No power, if I am very gentle on the gas pedal, I can manage it, but as soon as i try to accelerate, runs like crap, black smoke coming out of the exhaust.
The problem comes and goes, sometimes, the problem stops, and I can get going, no issues. Air filter is clean, even tried with no air filter, no differences., but it really sounds like bad air/fuel mixture.
Sonata NF (2006-10) :: 2008 GLS 2.4 Liter Won't Start - Throwing Codes P2110 / P2118 And P2119
My 08 2.4l sonata gls won't start. I started it this morning to warm it up while I cleared off all the snow, it was running for about ten minutes. I turned it off and about twenty minute later went to start it and it will not catch. All the electronics are running and the engine turns over but it won't start. I replaced the battery in December, the oil was changed last week as well as the air filter. It has 93k miles on it. What could be the problem? I did go borrow a diagnostic scanner and it is throwing a P2110 P2118 and P2119 code.
View 4 RepliesFord F-150 (2004-2008) :: Transmission Locked Up Throwing Fault And OD Light Flashing
My 2008 f150 trans locked up while throwing trans fault and o/d light flashing, won't move in gear or neutral ! At dealership waiting to be tore into in morning .
View 3 RepliesSanta FE SM (2001-06) :: 2004 2.7L V6 2WD - Codes For Sputtering / Sluggish Acceleration
2004 Santa Fe 2.7L V6 2WD ... Car was running fine, filled it with gas, and upon starting, heard a backfire into the intake manifold. It coded for a Cylinder 3 misfire so I had plugs and wires changed.
Now...The car starts, idles rough, accelerates sluggishly, and running rough any time it was around 2000 RPM. After I changed the plugs, it started bucking a little and stalls when I take off in the morning.
Coded and it's reading 7 codes, but some are duplicates:
-P0274 Cylinder 5 Injector Control High
-P0305 Cylinder 5 Misfire
-P0102 MAF or VAF A Circuit Low Input
-P0050 H02S Bank 2 Sen 1 Heater Circuit
-P0030 HO2S Bank 1 Sen 1 Heater Circuit
-P0274 Cylinder 5 Injector Control High (Shows Twice)
-P0102 MAF or VAF A Circuit Low Input (Shows Twice)
After having a backfire and then cylinder misfire...replacing the plugs and wires.
Ford F-150 (2004-2008) :: FX4 Won't Start / Sputtering For A While
I have a 04 fx4. Was sputtering for awhile. The engine light came on. Now it won't start even with a boost. What it could be has 290 clicks.
View 2 RepliesFord F-150 (2004-2008) :: 2005 - Intermittent Sputtering While Driving
It started completely unexpectedly about a month ago when I was driving around 70kmh while cruising. I would get a few "jerks" of a sputter, then was able to drive a km or 2 before it did it again. I drove to a friends and he got in, and the sputtering episode was over.
Since then, I cannot simulate the way I was driving to make it sputter for any mechanic, but I have been getting sputter on and off the last month.
The one time I got in the truck and started it, put the truck in drive, and it sputtered for a few seconds. I wasnt driving at all this time. This was the only time It sputtered in a stading position.
Here are a few points to maybe, narrow down what happens.
-I am usually driving around 70-90kmh
-I am usually under no loads (not towing, hauling etc).
-My mileage seems to be getting worse.
-this was normally happening not only when the engine was warm, but when it was warm outside and I was driving it for a longer period.
-When I started driving my truck I calculated around 16mpg city. I am currently getting around 13-14. I was on the hiway for around 250 km and got 14mpg. Seems I get better mileage when puttering through the city than when I am on the highway.
I had the truck in to a dealer 2 weeks ago. They did an injector flush, new sparkies, number 5 coil, and took me for $780, saying the problem is fixed.
A few days ago, I was driving on the onramp to the highway accelerating around 90kmh and for around 4-5 seconds I was sputtering and jerking so bad I thought I was done for. The truck finally recovered and again, haven't had any episodes since.
The dealership says their electrician doesn't know what to do, and would need my truck for 4-5 days to try to see the problem for himself. I can only think, as a non-mechanic, that it is something to do with some sensor, possibly a fuel, and/or oxygen sensor.
2005 F-150
4.6
88000km
gas
Ford F-150 (2004-2008) :: 2006 - Sputtering When Accelerating Heavy
I purchased a 2006 Ford F-150 XLT, 5.4 3V Triton. Last Thursday my check engine light came on, so I came to this forum and found out how to retrieve the code with out a OBD. It came up as a 0301 Misfire cylinder 1-10?
I went to the dealer and they said it was cylinder one, sold me a new plug and coil pack and they installed it for a nice $$$. On my way home it started to sputter again when you give it heavy throttle, I called they told me that I should change all the plugs and Coil packs, kinda makes sense but to have all 8 plugs and coils go at once it only has 83km on it.
Ford F-150 - 1997-2003 :: Throwing Codes P1451 And P0353
My trucks throwing 2 codes after traveling at low speeds and getting pretty warm. Drove it home after it cooled down. P1451 with is the EVAP Cannister Vent solenoid and P0353 which is Cylinder 3 Primary/Secondary Ckt. I keep getting told these are not connected but im not sure I believe that. Ive replaced the coil with 2 of my stock coils already with no luck, ive replaced the spark plug as well.
View 1 RepliesFord F-150 (2004-2008) :: Transmission Or Ignition Sputtering When Accelerate Slightly?
2006 F150 FX4 5.4L, 118k miles... At highway speeds (45-50) and (55-60) as I am slightly accelerating it feels like the transmission or maybe ignition system is skipping a beat. Kind of feels like a small bump. I replaced spark plugs with motocraft about 35K miles ago and recently all transmission fluid via cooler line. Had some concerns about system flush so I just drained and refilled entire system via cooler lines. I have read that it could be my COP's ...
View 7 RepliesFord F-150 (2004-2008) :: Shuttering / Sputtering At 40 - 60 MPH After Decelerating And Slowly Accelerating
I recently bought an 04 lariat crew cab with 56K miles 5.4 and auto trans. Before i bought it i complained about an exhaust noise and acceleration issue at 40mph and 1100 rpm as well as the ac not being very cold. They replaced the exhaust manifold on the passenger side, coil pack on the #3 cylinder, a transmission flush, a flash drive update and recharged the ac. This seemed to take care of the problem but i mostly drove under 30mph and did not notice it. I took it on a few road trips, and country roads and noticed the problem of sputtering and shuttering between 40-60 mph's after decelerating and slowly accelerating. The problem occurs consistently with ac and over-drive on in the above mentioned conditions and mph range. Problem is less noticeable with ac off and have not noticed it at all with over-drive off. It feels like a limited slip kicking in or driving on dry pavement in 4wd. Tranny shifts fine through all gears in a straight pull of acceleration and even full throttle pulls. Problem only occurs after decelerating and slowly accelerating. I don't know of any codes as I don't have a code reader, but I have not had any check engine lights come on nor has the dealer mentioned any codes.
View 7 RepliesFord F-150 (2004-2008) :: 2007 - Sputtering And Jerking - Power Loss?
i have an 07 ford f 150 5,4 liter. at speeds between 45 and 55 it has like a sputtering and jerking loss of power. I had a computer hooked up to it and it said fuel pump replaced it but it is still doing it, what this might be.
View 5 RepliesFord F-150 - 1997-2003 :: Stumbling A Lot - Throwing Misfire Codes On 1 / 8 / 4 And 3 Cylinders
Recently bought 98 f150 xlt 3 door 5speed 4x4 4.6l 230k miles for $1k was throwing misfire codes on 1,8,4,3 cylinders. Usually throws two cylinders at a time and never the same cylinders consecutively
Parts replaced:
coils...msd blaster
belden wire
motorcraft plugs...when i did these it ran perfect for a tank of fuel...18mpg no stumble
two cans seafoam through the tank
tank was dropped and drained
fuel filter
one can seafoam intake cleaner
3" exhaust from the Y pipe back
MAF cleaned
Previous owner said to have tested and cleaned injectors but I am not positive it was done... I don't think its mechanical because it wanders through the cylinders and when i changed the plugs it ran spot on. it gets worse the warmer the truck gets also.
injectors?
clogged small cats?
sensor?
Ford F-150 - 1997-2003 :: V6 Rough Idle / Black Smoke / Throwing 6 Codes
so i bought this truck about 3 months ago and it was running real bad when i got it, I went ahead and changed the lower and upper intake gaskets, cleaned throttle body, egr ports on lower and upper intake, did timing chain cover gaskets and 3 bad injectors i found while doing gaskets, truck ran better but still black smoking(running rich) and getting 8 mpg. So I changed fan clutch,fuel pump fuel filter,airfilter,MAF sensor(old one was pulling 14.4 volt), DPFE sensor and all 4 oxygen sensors(old ones carboned up and real sooty).
I've checked my egr valve while idling and when it opens the engine just about stalls, truck seems to be running better but CEL light came on again and is throwing these CODES:
P0453 (evap emission ctrl sys pressure sensor high input),
P0141,
P0153,
P0135(oxy sensors),
P0401exhaust gas recirculation flow insuff detected,
P0460fuel tank level indicator circuit error.
And I believe I've told everything i know ...
Ford F-150 - 1997-2003 :: 2001 5.4L Throwing Codes PO135 / PO155 / PO174 And PO171
I have a 01 f150 7700 with a 5.4L and its throwing codes po135, po155, po174, and po171. Here is the history, last year had same code and found it was a bad ELLBOW on pcv hose, replaced and that fixed it, I also had a crack on egr valve and I replaced that too. This Jan truck was running bad in the morning and I traced it to a bad idle air controller, replaced it. I got a code and guy said I had a bad pcv valve so I replaced it.
About 3 weeks ago check engine light came back on with the 4 codes listed above, I replaced both front o2 sensors, 250,000 mile so I thought that was it but came back same code, I took it to a local mechanic and he said that the intake gaskets need replaced, but he call me later and said I had no leaks on the intake and that he did find another vac leak. He didn't charge me anything and sent me on my way.
I drove the truck about 50 miles and same codes back, so to recap I have cleaned mad sensor, replaced both front o2 sensors, a new egr valve, a new idle air control, pcv valve, pcv hose and ELLBOW, don't know what to look at next. Any clues?
Ford F-150 (2004-2008) :: 2007 F150 Sputtering After Fill Up - Fuel Tank Pressure Sensor
The ole 5.4l hit a snag today. I was on my way to fill her up and she started sputtering and damn near died! i filled her up and it was like nothing ever happened. Took her to AutoZone and the diagnosis was a Fuel Tank Pressure Sensor.
I have a connection with Bumper-to-Bumper to get the part for cheap but I'm not sure if i want to dive into either moving the bed or dropping the tank. I'd prefer to move the bed.
Ford F-150 (2004-2008) :: 2005 - Sputtering / Taking Long Time To Start And Now Not Starting At All - Code P0191
2005 5.4L She would have a hard time starting before but after I replaced and fixed everything below she was running really good. Now back to sputtering, taking a long time to start and now not starting at all.
I have replaced; Fuel Pump, Fuel Filter, FPDM, Plugs and COP's, FRP Sensor, followed the power wire from the FDPM and found it corroded bad so I replaced it, also changed the ground location on the FDPM, I have checked all the wires from the FDPM to the drivers seat, checked all fuses.
I have power to FPDM and I have the diagram for the plug but how can I test (hotwire) the Fuel Pump without lowering the fuel tank? What should be the voltage coming from the FPDM plug? not sure about pin 1 & 6.
How can I test the FRP sensor? what are the specs for voltage?