Ford F-150 (2004-2008) :: 2006 XLT - Replacing Wheel Hub Assembly?
I've got an 06 XLT 4x4 with the 4.6L. I'm replacing the wheel Hub bearing assembly this evening and got the old one removed. Opened the new on to find no grease! I was shocked considering I just replaced the IWE and they come pre-greased. I plan on adding some grease around the hub gear but wondered if i should some how get grease in on that inner needle bearing? I have to have this put back together in a couple of hours so I can drive to work tomorrow.
View 6 RepliesFord :: 2006 - Motor Mount And Front Stabilizer / Rattling Noise From Driver Side Engine Compartment
My 2006 AWD LTD 500 has about 52000 miles on it; a slight rattle/clunking noise is intermittently heard on driver's side in engine compartment. Took it in to dealer who says motor mount is cracked and front stabilizer bar joints are worn and both need replacing. Car has only been driven on highways or for short trips (3-4 miles) and has had no impacts nor been driven over rough roads or run over any potholes or such. Should the motor mount be damaged? At 52K miles?? Never heard of such a thing. Ditto, the stabilizer bar joints: worn out in under 60K miles? What can I do about this? Who seek relief from? Ford warranty is, of course, over, and supplemental warrenty will only cover motor mount replacement but not stab bar. Are these parts routinely wearing out at such an early date that repair shops can reap the rewards???
View 4 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle After Replacing Ignition Coil
completely stock 2006 4.6, 230,000 miles, I purchased and can vouch for everything after 106,000.
Two separate issues...have had a slight ticking noise growing for about the last two years. Seems to get slightly worse near an oil change but that could be my imagination. It has finally gotten loud enough that my wife (who drives with the delicacy and observational skills of a Sherman tank driver) actually mentioned it to me the other day. It is directly related to engine speed whether the truck is in gear or not. I kind of think it might be a manifold gasket going out but am not sure. Am not very worried about it but...felt like I needed to mention it because of my bigger problem....
Truck has gotten very "cranky" on startup in the last week. Has a rough time finding an idle speed but typically sorts itself out after about 5-10 seconds. This afternoon it started idling rough at a stoplight. It got steadily worse and noticeable even at speed. Four stoplights and nine miles later it threw a code and coincidentally, I was in front of an Advance Auto. They read it and said the #3 cylinder was not firing. I bought an ignition coil, drove 15 miles home and changed it. From everywhere I looked online, this is the second cylinder from the firewall on the passenger side.
Had a little trouble getting it in and am not entirely sure it is fully seated in the slot, but I can't get it to go any further. Seems as tight as a couple of the others. I disconnected the battery to clear the codes, cranked it up and it seems to run "better", but still has a rough idle. Just test drove it about 12 miles and no check engine light but the idle has not cleared up. I think coil must be working fine because I have no issues at highway speed. Earlier, when I backed off the gas you would feel the miss very badly, but not as much when under a load.
Prius (2004-09) :: Oil Leak Near Motor Mount
Cleaned the engine and determined the location of this oil leak. I am posting two pics. The far away shot shows the leak in the center of the picture...near the motor mount. The close up pic u can see the leak coming from a vertical seam just Below where the half shaft enters the transaxle. It is definitely motor oil, not transmission oil.
View 5 RepliesFord F-150 (2004-2008) :: 2006 - Whine From Motor Which Gets Louder With Increased RPM
My truck seams to have developed a whine. It gets louder with increased RPM. Sounds like its coming from the motor, specifically the front of the motor, maybe one of the pulleys? Water pump??? Alternator??? Im not sure but Im about to head out on a 2800 mile round trip pulling a heavy load and want my truck to be ready for the trip...? It sounds like its gotten louder in the last couple weeks but I think its just because I had a new manifold installed on one side and the truck is quieter making this seam louder.... But I don't know if I should be worried about it.. I don't want to waste money (right before a big trip) chasing a noise if its not something that is an issue..
View 6 RepliesFord F-150 (2004-2008) :: 2006 4x4 Light Not Coming On - Actuator Motor Sticking
Just picked up a high mile f-150 (146,000) 4x4 light not coming on. Jumpered out the vacuum solenoid first, nothing. Then found out I could try to tap on the actuator motor at transfer case. it worked,. Just wondering if i keep exercising the actuator motor, if it will continue to work, sounds like the previous owner did not put it in 4x4 for a long time. Also, if needed, where is a good place to purchase the replacement actuator motor? If this truck has heated seats ( it is a lariat), where is it controlled from? .... Seems to ride a little rougher than I expected. New tires, but it seems a little harsh. I have an f-350 as well. It seems to ride just about as good.
View 3 RepliesPrius (2004-09) :: Oil Drops Dripping From The Bottom Motor Mount?
I have noticed oil spots under my 06 lately and finally got under it to see where it's coming from. It's collecting and dripping from the bottom motor mount but it's hard to determine exactly where it's coming from. I can't tell if it's coming from higher up or down low and running back and up from the wind. I just cleaned it with degreaser and have it running to hopefully dry it and be able to see where it's coming from.
View 11 RepliesFord F-150 (2004-2008) :: Excessive Play Between The Mount And Receiver?
I have a 2" ball mount and a 2" ball from my previous vehicle. That vehicle was equipped with a 2" receiver as well.
Recently I had been pulling a few stumps in the front yard...nothing major, but this was the first time the ball mount has been used in my '06. So I noticed that there is some excessive (to me at least) space between the mount and the receiver on the truck. This causes some rattle between the two. I know there are collars out there that I can use to remove the rattle, but my question is...have others of you noticed the same? Do any of you have excessive play between the mount and receiver?
Ford F-150 (2004-2008) :: Mount Of Weight Tail Gate Can Support?
I'm wondering what the safe limit is for the amount of weight the tail gate can suppport ?
I need to get some 4x8 sheets of dry-wall and instead of leaving the tail gate down i'd rather have it up and support the pieces, but at 50-60 pounds a sheet I'm somewhat concerned about how many sheets the tail gate can support without causing issues.
Ford F-150 - 1997-2003 :: Cannot Get Engine To Line Back Up With Motor Mount?
I have a 97 f150 4.6 4x4 i cant get my engine to line back up with the motor mounts. Is there a trick to doing this? I've tried to lift the motor several different ways, but still nothing. Its like the motor isn't going back far enough. But it cannot go back any more without hitting the trans?
View 8 RepliesFord F-150 (2004-2008) :: 5.4 4x4 - Replacing Starter On Truck?
I may have to replace the starter on my truck. Have heard it is difficult especially on the top bolt. Any stickys/bulletins on how to do this.
View 1 RepliesFord F-150 (2004-2008) :: 2007 - Replacing Turn Signal Flasher?
I'd like to put in a louder turn signal flasher on my 2007 F150 - where is it located and where I can get a louder one ?
View 1 RepliesBuick - Century :: How To Replace A Motor Mount
The vehicle in question is a 96 Buick Century. I don't use it a whole lot, but occasionally lend it out or use for some undesirable task. Anyway, I have to get it to pass inspection.
View 4 RepliesCamry :: Change All Support Mount Motor Of 2003 V2.4l?
I need to change the all support mount motor of my Camry 2003 v2.4l. but I don't know where find the best model or manufacturer.
View 2 RepliesPassat (B5) :: Passenger Side Motor Mount Cracked Out
My passenger-side motor mount is cracked out. Is this a common failure? The aluminum part that connects the "frame" to the engine mount is cracked, the hydraulic rubber mount looks almost new, not sure how the previous owner missed the crack in the aluminum. Car has 140K miles on it. I'm thinking about just having it welded up.
View 8 RepliesFord F-150 (2004-2008) :: Replacement Motor For 5.4 Vin V
I'm looking for a replacement motor for a 5.4 08 vin v. Do the 9-10 motor with the same vin code v. I know intake is different but the heads are the same.
View 6 RepliesGolf IV / Jetta IV :: Passenger Side Motor Mount Spacer
What hardware I need to install the passenger side motor mount spacer from Euro Image Tuning. Been sitting on it for a while and cant find the hardware that it came with. Would like to install it, but dont remember what it came with..
View 2 RepliesPassat (B5) :: 1999 - Passenger Side Motor Mount Leaking
The passenger-side motor mount on my '99 1.8t has blown (again). I'm on my second mount already and want to make sure I address all other possible causes before I go through another one. Looking for keeping this new mount intact a bit longer? (BTW the original mount lasted approx. 120k miles and the replacement has "only" lasted 85k miles)...
View 4 RepliesGolf IV / Jetta IV :: Broken Bolt From Motor Mount Bracket
The other day when i wanted to start the car, I found out my battery was death so i decided to ask my buddy to push me and crank it on gear. Car shakes as normal and engine started, but then i heard a weird noise like if something was rubbing. I turned it off and popped the hood. I found my engine leaning forward and toward the passenger side.
So the next morning, I checked the bay again and i found out that it wasn't the motor mount. Motor mount is ok, but then i found a broken bolt that holds the bracket to the block; the one that goes right next to the water pump to be more specific. Also in the back of the block there is a bolt that hold bracket to the block again and the thread whole was enough weak to break when the other bolt failed. So I did some research and i found that there is a solution for the bolt in back of the block.
What I am concerned is for the on the goes right next to the water pump. It seems that it broke the whole thing including the part where the bolt threads go. I just had a shop install I.E connecting rods, new piston rings, and rebuilt the heads. They put a new timing belt kit and all its job required. I think they might have a bit of fault on this since it had to be removed when they did the timing belt kit. Anyways I don't want to think my block will be a junk now because engine is running like a champ, and that would be a bummer.
-Bolt that is broken in two pieces.-
-And where it is attached to the block-
-Part of the engine where this all goes.-