Ford Super Duty (1999-2016) :: With Auto Hubs Shift On The Fly Selector Is Turned To 4X4 High Or Low?
After reading the book, I'm afraid I still don't understand. When the hubs are in AUTO, & the shift on the fly selector is turned to 4X4 high, or 4X4 low, is the truck in 4 wheel drive. What happened to free or lock.
View 3 RepliesFord F-150 (2004-2008) :: 2006 - Shocks Making Strange Noise?
Ok, just asking a question for a buddy. He has 78k on the truck and the shocks make a strange noise. When one of us bounces the truck up and down on the bumper (simulating a load) the shocks "click". Now I looked and it looks like the bushing may be wore out, and the actual bolt that goes through the upper shock mount is touching the top and then the bottom, emitting the "clicking" noise. Is this just a normal wore out shock, or perhaps a defect? Just asking because I am not as familiar with suspension systems.
View 1 RepliesFord F-150 (2004-2008) :: 2006 Truck Making Noise That Is Coming From Engine
My 2006 f150 was making a noise that's coming from the engine. It sound like rocks in the engine. When I'm going 50-60 MPH the engine starts to make a sounds like rocks in the engine. What's happening. When I go about 40 it stops.
View 12 RepliesFord F-150 (2004-2008) :: 2006 - Door Making Squeaking Noise When Going Towards Closed Position
I have just purchased an 06 long bed f-150 with high mileage on it. I am going thru it slowly as time permits. I had found the passenger door stop, not the hinges, to be making a "quite" squeaking noise as it is started toward a closed position. A simple drop or two of oil I am thinking, but it then really increases in sound. I then clean it off and apply a synthetic grease, still loud, maybe louder. I finally got it back to a "quite" squeak again by cleaning it. Use lubricant, or should I just leave it cleaned as it is now?
View 1 RepliesFord F-150 (2004-2008) :: 2006 - Ticking Sound When Drive - Hubs Not Locking
Ok, So, Im 40 miles from home stuck in ice and snow in a hotel.. (my wife works close by- thought it would be safer than driving in the 10 inches of snow we got 3 days in a row) so, I go to pick her up tonight and I engage 4hi.. I hear the click and the light comes on.. but no clunk of the hubs locking.. I drop it in 4 lo.. it shifts in low.. but the hubs are not locking..
I hear a ticking sound as I drive and when I put it in 2wd it goes away. I turn off the truck, turn the wheel hard both ways .. get out and I can physically turn the drive shaft and I hear the ticking in the hubs. If I read correctly when the truck is off these should be locked?
is it possible the vacuum is not releasing? I also get the groaning when I start up of the air diverter.. that im told is operated by vacuum.. so I am guessing I have a vacuum problem??
Ford F-150 (2004-2008) :: 2006 - Making 5x5 Beeping Noise Shortly After Start Up - Truck Died Abruptly
i have a 2006 f-150 xlt, i was driving it today and it started making a 5x5 beeping noise shortly after i started it up. I read on a few forums that that beeping is a warning about the passenger airbag sensor or something. anyways it went away and kept driving for 5 minutes or so when suddenly the dash went out and all the gauges dropped but i was still able to drive fine. A minute later the engine just died and i managed to pull over to the side of the road. now nothing works when i turn the key, not even a light, its just a dead weight, the remote locking doesn't even work. the only sign of life is a LED from my phone charger that is plugged into the outlet. the battery is only 2 months old so its not that.
View 2 RepliesFord F-150 (2004-2008) :: Hubs Won't Engage Only Make Grinding Noise?
I have a 2005 F150 113,000 FX4. When I put the truck into 4x4 high the light comes on and the front driveshaft engages. Same with 4x4 low. the problem is that the hubs never actually lock. When I move forward in some mud or wet grass the right front hub makes this grinding noise like it is actually trying to engage but never does. Same with 4x4 low. I do not have any weird noises when I drive in 2wd.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 - ESOF Hubs Won't Lock In Auto
New to the 4x4 6.0 just bought an 06' King Ranch 130K miles. My other truck is a 95' 7.3 non 4x4 now for sale. So the new to me 06' will not lock the hubs in Auto mode but will in Manual. I have good vacuum down to each wheel hub which is where my question is.
The vac port at either wheel I get 20-30hg however I believe this is only because something is plugged. If I pump up my vac tester to ~25hg right at the wheel port the needle doesn't move, holds vacuum, but does not Auto lock the hub. So I pulled out the Manual/Auto hub by removing the 3 torque screws thinking my vacuum should then go to 0 but it doesn't it stays right at ~25hg.
Before I bought the truck there was some work done to the front end. New ball-joints, Rt tie-rod and perhaps a few other things I haven't ID yet. Could my problem above be an axle seal or something else perhaps installed incorrectly causing the small vac hole going down inside the hub to be covered up or maybe plugged somehow? I believe to replace the ball joints the axle, hub and other parts have to be removed, correct?
Ford Super Duty (1999-2016) :: 2008 F350 - Auto Hubs Won't Stay Locked
2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 RepliesLexus GS 2006-11 :: 2008 350 AWD -VSC And CEL Came On, Auto Trans Won't Shift Past 4 Gear
My VSC and check engine light have come on. In addition now the auto trans will not shift past 4 gear with in auto or with me doing it manually. My local shop who has worked on this car before and is very good put the computer reader on it and got a P0500 for vehicle speed sensor "A". Today they put it on the real monitor and it reads a different code that says check engine code but does not reveal the code to read.
I really don't want to go to my dealer and get it hard. The car has 175,000 and until now has run great. I tried the gas cap fix to no avail. The shop did a reset when i first got there and it last 75 yards.
Toyota - Avalon :: 2012 - Moving Auto Stick Shift Awkward?
My wife and I test drove a 2012 Avalon Limited at our local dealership. It was a demo that they were selling as a new Toyota at a $5,000 discounted price.
We loved the TAL but we found that moving of the automatic stick shift to be a little bit awkward. This bothered my wife more than me. We had to move the auto shift stick from side to side and then forward and backward to go between Park, Reverse, and Drive.
On our 1988 Toyota Supra that we still love to drive, the auto shifting between Park, Reverse, and Drive, and the lower Drives is easy. You just move the automatic stick shift forward and and back to change gears. It was the same on our 1988 Toyota Celica GTS, another wonderful car that we sold to a friend recently.
We should have asked the salesman about the automatic transmission stick shift but we asked lots of other questions instead.
So what can you share with us from your experience? Did you get used to moving the auto shift stick from gear to gear easily? Is there a safety reason for this shifting alignment?
Ford Super Duty (1999-2016) :: 2006 6.0 F350 4x4 Auto Hubs Will Not Engage
I was using 4x4 High the other day and it was working just fine. Now today, I was at my first parking lot to plow and used the ESOF to shift into 4x4 High and it did not engage with the hubs being in auto mode. The lights on the dash show up indicating that I am, but I am still in 2wd.
If I manually lock the hubs, it engages 4wd high. I tried the same thing using the ESOF to switch over to 4x4 low and it does NOT engage either.
I also noticed that heater blower was switching over to full defrost even though I had it set on the floor setting (manual heat climate *****).
Does this sound like a vacuum leak? I haven't had a chance to test the lines yet. Btw, this is my second work truck and not the one listed in my signature below. It's a 2006 f-350 6.0 xlt.
Ford F-150 (2004-2008) :: 4wd Won't Working And Making Noise?
2004 F150 Super Crew Lariet 4x4 with limited slip. Center console with electonic switch 2wd/4hi/4lo on dash right of steering wheel. My 4 wheel drive does not work.
When the truck is in 2wd I have no issues, no sounds(I've heard anyway) or anything. The only questionable is when turning with wheel at full lock in either direction at low speed, my front wheels grab/lunge. Not sure if that is normal or not on these trucks.
When I put it in 4wd in the snow, it acts as though it wants to engage, but the second any power is applied to the wheels, the back wheels just spin and it makes a higher pitched grinding/chattering noise up front. It will also lightly clunk into 4wd with little power applied to the wheels, but once it has accelerating power applied the front diff "pops" and is clearly no longer engaged.
When in reverse in 4wd, it makes no noise, but still doesn't work.
Yesterday I had it in the shop for an oil change and to rotate my tires. While it was all off the ground I turned the ignition on and put it in 4wd. Both back wheels turned it the same direction(limited slip) as they should, and the front left wheel turned fully engaged with them. The front right wheel did nothing and turned freely on its own(assuming because front it open diff?). One oddity noted, when the back wheel were rotated one full revolution, the front rotated 2 full revolutions(also assuming this is because of the front diff being open and rear being locked?).
When I spun both front wheels by hand regardless of 4wd turned on or not, IIRC, they both made a clicking/ratcheting sound as the spun.
I left it in 4wd when I brought it back down on it's wheels and backed it out of the shop into the unplowed area of snow, I lunged the throttle a touch and the front end dropped as the front wheels gripped and slightly broke loose in the sticky snow. It was fully engaged and working properly for a second. I then put it in drive and tried to move forward, soon as any power was applied it "popped" out of engagement in the from diff and was back to 2wd and light grinding noise.
Another note, our first big snow fall a few days back is when I first had a real issue with the 4wd not working at all. It had snowed pretty well and I didn't feel like shoveling the driveway because I was running short on time to make it to work and my wife had the day off work and didn't need to go anywhere. I started it, put it in 4wd, let it warm up a bit, proceeded with trying to leave. This is when it all began with the 4wd not working at all and grinding. As it made that noise, it sounded pretty light to me in the cab even with the window down. But, as my wife noticed me stuck in the driveway she stood in the front door watching with the glass storm door still closed. She said she thought that "light" grinding noise I heard, was actually quite loud from where she was standing, 60+ ft away.
Previous issues I've noticed with my 4wd that may diagnose my exact issue, it has had a frequent issue the past year or so with, when engaaged, if I applied too much acceleration, from a stop or not, it would suddenly "pop" out of engagement as I've previously noted on, but I would immediately let off the throttle and it would reengage right away.
On two other occasions, it has refused to engage into 4wd no matter what. I simply contributed it to the extremely cold weather during the occurrence, as it worked just fine the next day and/or the next time I placed it in 4wd.
4hi/4lo light always lights up in the gauges as they should and as if everything is working normal.
So, IWE's? Actuators? Vacuum?
Ford F-150 (2004-2008) :: 2006 - Hard Shift In OD?
2006 F150 5.4L, 4wd, Ext. Cab, 90k or so
In OD only, when passing gear kinks in going approx. 35 mph. transmission shifts hard...
Having transmission or TC problems? Hard shifting problems? Etc.
Ford F-150 (2004-2008) :: While Shifting Down Making Vibration Noise?
I have a 08 f-150 super crew 4x4 and driving down highway or just on main roads,when ever my truck down shifts it make a quik vibration noise, kinda like driving on a washboard road.
View 5 RepliesFord F-150 (2004-2008) :: Making Roaring Noise After Playing In Mud?
The front of my truck is making a roaring noise after playing in the mud while your going down the road is the only time I hear it. It sounds as if I have really aggressive tires on it. I did do my best to clean out from under it... It doesn't seem to feel like its dragging. 4x4 engages fine? I mean it started only after a few days of playing in it, I didn't wash the mud off right away. Should I be concerned? I mean if its just some dirt up against something, then that is no big deal, but my ranger whined when it was low on differential fluid. However its not whining, just roaring.... Should I be concerned? Truck drives fine... no issues there.
View 5 RepliesFord F-150 (2004-2008) :: Rear End Making Weird Noise / Truck Shaking
Ok I have a 2004 F150 Fx4 ext. cab. I had the truck for sale and due to something coming up I was unable to sell it. Kinda wish I did now. But anyways the truck was running great up until last week. I was drove it to work which I normally dont do. On my way home the rear end was making a weird noise. Kinda like a brake sticking. I tapped the brakes a few times and it seemed to work. Then a mile down the road it was doing it again without me trying to come to a stop and the back end was shaking. I pulled over and crawled under the truck to see if a u-joint was going bad. Everything seemed good. It never happened again until today.
This morning I hoped in the truck and went to my parents house. Its about a 5 mile drive and truck was acting fine. Came home and it was still fine. A few hours later I figured I would go up to the fire department I am on and find something to do up there. I got in the truck and didnt make it 5 feet from where I was parked and there was this bad noise followed by my whole truck shaking. It felt like the truck was going to fall in pieces in my driveway. I stopped looked around and didn't notice anything wrong. I figured I would just try to drive a little bit further and it was even worse. So I put it in reverse and it was normal. I put it in Drive again and thought my teeth were about to fall out of my mouth.
What could cause this? I know my transmission was leaking some oil from where the gear shifter comes out. I would check the trans fluid and add some if needed. I drove it up to the fire hall Monday night and did notice a slight burning smell but that was the only time I smelled it. Could it be the transmission?
Ford F-150 (2004-2008) :: 2005 - Won't Accelerate - Making Noise - Fuel Injector?
I bought a 2005 F150 supercrew w/ 5.4 Triton engine brand new. It now has 16000 miles on it and all was well until...
I was driving to work 2 days ago and all of a sudden my truck started acting all weird. I couldn't accelerate and it seemed as though I was driving over rumble strips. I went directly to the garage and they told me that 2 fuel injectors mal-functioned and that flooded everything with gas. I needed 2 injectors and 8 spark plugs. The next day the garage called and said that they replaced the parts but now there is a terrible knocking noise and that I needed a new engine.
I am not a car wiz so what other things should I be aware of? What other questions should I be asking?
Lexus GS 2006-11 :: Seat Making Sounds When Moving Back And Forward?
So It's been a while since I've noticed this wearing rusty sound when moving the driver seat forward and back. It only happens at a certain point where I feel most of my family members are positioned when driving.... I took a look it seemed a bit rusted... Will post pics later.
View 3 Replies