Ford 6.0L Power Stroke Diesel :: Vacuum To Auto Hubs Leaking?
When I park over night while in 4x4, the next morning my hubs are disengaged and I have to manually lock them. There is an apparent slow/slight leak in the vacuum system. What would be the usual suspect, so I can start at that point?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Water In Auto-locking Hubs?
I got new auto-locking hubs. The updated ones. As I proceeded to replace them, I pulled out old ones and when driver side came out, there was like 1/2 ounce of water that flowed out from where the auto-locking hub would sit. Strange. I had changed out lines, vacuum pump, vacuum solenoid and reservoir. All new and dry. I blasted both sides down with brake cleaner to clean off old grease, let dry and installed new auto hubs. So far so good. Will test the ESOF feature another time. I was wondering where this water would come from? Other side of wheel hubs are dry.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: ESOF Won't Engaging Hubs?
I have my vacuum system back up and working and using my vacuum pump I determined my lines are all good. They hold a vacuum fine, but my ESOF isn't engaging my hubs. I guess that leaves either the selector on the dash or the seal at the hubs.
If it is the selector, I should just be able to just disconnect the vacuum line at the selector and use my pump to engage my hubs. How much it is supposed to take to activate the hubs?
Ford 7.3L Power Stroke (1999-2003) :: Vacuum Shutoff For ESOF Hubs?
I am thinking on installing a shutoff in the vacuum line that supplies the hubs so I can use 4LO for backing uphill with a trailer without having the hubs engage. Its either that or a switch to disable the PVH solenoid.
View 12 RepliesFord 6.0L Power Stroke Diesel :: Unable To Move Selector On Lock Out Hubs
I have a 2003 f250 and I am unable to rotate the hubs from automatic. I have removed them and while I had them apart, I was still unable to rotate the selector. It wouldn't turn even with a crescent wrench putting pressure on it. I repacked them with grease and reinstalled and they still work when in 4 wheel drive. I am just concerned that when the vacuum does go out, I will not get the hubs to manually lock in.
View 10 RepliesFord 6.7L Power Stroke Diesel :: Locking Hubs To Auto Damage Drive Line System Components?
Just notice this in the manual page 302 The vehicle should not be driven in 4x4 high or low with the lock hubs set to auto as this condition may damage driveline system components.
Page 303 It then goes on to say !!
Automatic operation of the hub locks is recommended and will increase fuel economy.
when using 4x4 once in awhile LOCK or AUTO
Ford Super Duty (1999-2016) :: How Does ESOF Locking Hubs Work In Auto Mode
I took apart, cleaned and lubed my hubs. My question is: how does the vacuum make the gears work?
Does the vacuum force (suck) the nylon assembly to push the outer gear towards the center of the truck, sliding on the inner gear thus engaging the teeth so that the axle shaft turns the hub?
When the vacuum is gone, does spring pressure pushes the outer gear away from the center of the truck thus disengaging the teeth from the inner gear and allowing the hub to free wheel?
Is this vacuum source constant during 4wd and not present during 2wd or do I not understand how the system works? I have read about a “vacuum pulse” that locks the hubs and another pulse that unlocks the hubs and this confuses me.
BTW, I like the way the Auto lock works. I had a set of Warn Auto Lock hubs on my 78 CJ. They worked on the principle of a set of roller bearings that would lock (pinch) when there was torque coming from the drive shaft. There was no vacuum involved at all. The down side was that when you coasted, the front hubs would be in two wheel drive and so you would not get the engine braking on all 4 wheels. These ESOF seem to have solved this problem.
Oh, I should probably tell you that I just purchased my 04 F250 SuperDuty 4x4 with the 6.0 diesel, just had it a week. It has been 18 years since I owned a 4x4. Before this I owned an 87 F250 2wd with the 6.9 diesel.
Ford Super Duty (1999-2016) :: 2000 F250 - ESOF Auto Hubs Not Engaging Automatically
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
Ford Super Duty (1999-2016) :: 4WD Is Only Working Now When Manually Lock The Hubs - ESOF Vacuum Leak
I noticed that my 4WD is only working now when I manually lock the hubs in (they have that options!), and the air blows out the defroster when I shift, so it looks like I have a vacuum leak. Where are the typical leak points on a 2006 F250? What's the best way to confirm a leak (other than just replacing all of the hose)?
View 2 RepliesFord Super Duty (1999-2016) :: 2005 4x4 ESOF - Hubs Seem To Lock Automatically As Getting Binding While Turning?
My 2005 has the ESOF system which has worked flawlessly. Recently I had upper and lower ball joints done and after that repair I had no auto locking hubs. ( independent shop messed up seal install ) they redid the job and it now seems like my front hubs are locking automatically because I am getting binding while turning. So this is the problem.. the front wheels do not "pull" only the rear wheels spin. If I manually lock the hubs I have 4x4 and can get out of being nearly stuck and everything works normally. What is wrong here? Does the shop need to redo the job again?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Switch From Manual To Auto Locking Hubs?
I know this is going to sounds lame, my wife can't turn them, they have cover over it that has to be unscrewed to get at 'em. It would be nice to shift in and out "on the fly" as weather condition change.
Is it a difficult change?
Ford 7.3L Power Stroke (1999-2003) :: 4wd - Tires Not Pulling When Manually Lock Hubs
My transfer case engages the front drive shaft spins but even when I manually lock my hubs neither of my tires will pull! I was thinking either the hubs are shot but I was told it could be the 4wd locking solenoid??
View 1 RepliesFord Super Duty (1999-2016) :: 2001 F250 4x4 - Auto Lock Hubs Are Not Working
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 RepliesFord 6.7L Power Stroke Diesel :: Strange Noise From Front Hubs
Coming home from a trip with my truck pulling the 5th wheel, we heard noises that seemed to be coming from the front hubs that sounded like stones in the hub caps. Once we got home I pulled the front lug covers to see if any came loose and were rattling around inside, but all were torgued properly. Everything drove strait and tight with no noticeable problems, should I be concerned....
View 8 RepliesFord 6.7L Power Stroke Diesel :: Unlocking The Front Hubs Improve Mileage?
I've been told that manually unlocking the front hubs on my '15 F350 dually, might just improve milage. Any concerns about the axle lubrication from being unlocked for extended periods of time? I rarely need the 4WD.
View 9 RepliesFord Super Duty (1999-2016) :: ESOF - Hubs Won't Disengage
I've read many posts about ESOF and fault vacuum lines and how that will prevent 4x4 from engaging. I experienced a different problem this past weekend. Here's the situation...
Was about 1.5hr drive up to the mountains. Outside temp when we left the house: 10F. Outside temp when we arrived at destination: 9F. Quite a bit of road grime on the way up from sand, slush, and that magnesium chloride (or whatever they hell they put on the roads in an attempt to keep it from freezing). 4x4 worked fine on the way up. 4x4 light on dash was on, and I KNOW I could not have climbed the snow-covered forest roads without being in 4x4. Also, I could hear and feel the front hubs turning.
On the way home, once I got to where the roads were sufficiently ice free, I turned the dial on the dash back to 2WD. 4x4 light goes out. But I can hear and feel the front hubs are still turning. Toggled the switch back and forth a few times. 4x4 light would come and go with the toggled switch. But the hubs didn't disengage.
When I got back into town (outside temp now about 5), we stopped at a red light and I toggled the switch again. This time, the hubs disengaged. Is this a sign of bad vacuum? Or more an indication of faulty hubs??
Ford Super Duty (1999-2016) :: 2006 6.0 F350 4x4 Auto Hubs Will Not Engage
I was using 4x4 High the other day and it was working just fine. Now today, I was at my first parking lot to plow and used the ESOF to shift into 4x4 High and it did not engage with the hubs being in auto mode. The lights on the dash show up indicating that I am, but I am still in 2wd.
If I manually lock the hubs, it engages 4wd high. I tried the same thing using the ESOF to switch over to 4x4 low and it does NOT engage either.
I also noticed that heater blower was switching over to full defrost even though I had it set on the floor setting (manual heat climate *****).
Does this sound like a vacuum leak? I haven't had a chance to test the lines yet. Btw, this is my second work truck and not the one listed in my signature below. It's a 2006 f-350 6.0 xlt.
Ford F-150 (2004-2008) :: 2006 - Auto Hubs Making Noise / Cannot Shift From 2wd To 4H While Moving
I recently purchased as used 2006 F-150 Lariat 4x4 with 77K miles. I am having an issue with the shift on the fly, I had a vacuum leak that was causing the auto hubs to make noise on occasion but it has never allowed me to shift from 2wd to 4H while moving. I have replaced the IWE solenoid and repaired the vacuum leak but it still will not engage while moving. The light for 4H comes on but the hubs will not engage. The dealer where I purchased the vehicle is not a ford dealership and whey have been trying to solve the problem but to no avail.
View 3 RepliesFord Super Duty (1999-2016) :: 2001 F250 4X4 - ESOF Switch Not Engaging Hubs?
I have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 Replies