Ford F-150 - 1997-2003 :: Misfire Error Codes And Check Engine Light
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
Ford F-150 - 1997-2003 :: Check Engine Light Has Been On - Codes PO401 And PO446 Came Up
Ive got a question for all you code readers out there. My dreaded check engine light has been on for about a month. I bought a code reader recently and checked it out. Two codes come up; PO401 and PO446. What these mean. My book says "Exhaust Gas Recirc. Flow Insufficient Detected" and " Evaporative Emission Control System Vent Control Circuit Malfunction". Which sensors, location on vehicle, etc..... this is a 97 5.4L Expedition.
View 9 RepliesFord F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford F-150 - 1997-2003 :: 2000 V8 Running Rough At Idle And Check Engine Light On
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
Ford F-150 - 1997-2003 :: Engine Revs Up And Stops Accelerating Usually When Shifting Around 30 - 35
2001 F150 5.4 v8 ... In the past few months my truck has been a bit strange, but in the past few weeks it's gotten to the point I'm nervous to drive it. Usually when shifting around 30-35, the engine revs up and stops accelerating and I have to take my foot off the pedal to make it return to normal. It doesn't do this after I do that, but the past time I tried to drive I couldn't get above 35 and the rpm was in the upper 2000s going at a constant 35. When I stop for any reason such as making a turn, when it shifts it lurches forward and I hear a loud clunk.
Naturally, I've checked all the fluids and fuses and they're all fine. The mechanic I regularly visit insists that nothing is wrong with it.
Ford F-150 - 1997-2003 :: 1999 - Low Idle With No Codes?
I have a 1977 f250 460 with c6. As far as I now everything is stock on the motor. The carb is a motorcraft but I cant see what model it is, there is a ID tag that I need to get the numbers off of so I can see what I have.
I don't know much about carbs so I'm trying to learn as I go, but what has me wondering about the secondaries is going up inclines. We have a canyon that is a decent grade and long, I was towing a empty flatbed trailer and with my foot all the way down could never get it above 40 mph it just felt like that was it. I have been out playing with no trailer and it feels like I can get them to open up when it down shifts, but cruising along at 55 and stomp it nothing.
I am worried about pulling our camp trailer with it and that is the main reason I got the truck with a 460. What to check?
Ford F-150 - 1997-2003 :: Stalls At Idle - No Codes
My buds 2003 4.6 liter stalls every time he takes his foot off the pedal. Runs fine otherwise, no roughness or anything, you just have to keep your foot on the thing to keep it from dying out.
We checked for codes and found none. I checked vacuum connections and they looked OK.
Is there an easy way to test the IAC or should we just throw a new one in and cross our fingers? If we do change it out, does the truck need to be driven around a bit for the computer to re-learn anything?
Ford F-150 - 1997-2003 :: 1999 5.4L - Low Idle With No Codes
The truck ran fine this morning and this afternoon I had trouble with the truck running at idle.
The idle is at about 450RPM in park. Runs smooth with no miss but if you bring the idle up and then let off quickly it stalls. Can stall while trying to idle at warm up also. Sometimes it will stall at a light but I think it is related to taking my foot off the pedal quickly.
There is no check engine light on and there are no codes. I have 138K on the engine now. Both air & fuel filter were replaced about a month ago as well as the PCV valve.
Ford F-150 - 1997-2003 :: 2000 - High Idle With Codes
I will try to keep this short. Picked up a 2000 f-150 4.2 for my nephews first truck last night. Bought it blind against my better judgement, but the price was right. Got it home, odometer didn't work, fixed the solder joint and was happy it only had 132k on it. Heater core was plugged solid. Got it flushed and at least now its has luke warm heat until I have time for a full coolant flush and new core.
Next on my list is the high idle and engine lights. Its idles around 1300-1700, cold or hot sometimes it drops down. I only have a cheap scanner, but I have 2 codes. PO171 and PO174. Where should I start with diagnosing this? I would assume vacuum leak. Any common spots to check on these?
Ford F-150 - 1997-2003 :: Idle Drops When AC Turns On - Codes P0171 And 174
So I have a 1997 ford f150 v8 4.6 2w... I got codes p0171 and 174 my truck seems fine till the idle drops, it's weird when I have it on park it's fine if I turn the wheel left the idle drops when the ac turns on the idle drops and it's wasting crazy gas. Where should I start first in finding this problem?
View 12 RepliesFord F-150 - 1997-2003 :: When Engine Revs It Continue At High RPMs For About 10 Seconds After Letting Off The Throttle
2001 F150 5.4 4x4 148K... I recently replaced the intake manifold on this truck and when the engine revs it wants to continue at high RPMs for about 10 seconds after letting off the throttle. When driving, it almost wants to go faster and the gas mileage is really bad. Had some codes come up and took it to AZO and had them checked. P0171 & P0174. Guess I need to do some testing on the MAF and injectors.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 - Rough Idle / Codes PO304 And PO174
I have a 2000 F150 4.2L and I have 2 codes PO304 & PO174 so far I have changed my plugs & wires,fuel filter,mass air flow sensor, and coil pack...it is still running rough under a load and a little rough on idle..
View 9 RepliesFord F-150 - 1997-2003 :: V6 Rough Idle / Black Smoke / Throwing 6 Codes
so i bought this truck about 3 months ago and it was running real bad when i got it, I went ahead and changed the lower and upper intake gaskets, cleaned throttle body, egr ports on lower and upper intake, did timing chain cover gaskets and 3 bad injectors i found while doing gaskets, truck ran better but still black smoking(running rich) and getting 8 mpg. So I changed fan clutch,fuel pump fuel filter,airfilter,MAF sensor(old one was pulling 14.4 volt), DPFE sensor and all 4 oxygen sensors(old ones carboned up and real sooty).
I've checked my egr valve while idling and when it opens the engine just about stalls, truck seems to be running better but CEL light came on again and is throwing these CODES:
P0453 (evap emission ctrl sys pressure sensor high input),
P0141,
P0153,
P0135(oxy sensors),
P0401exhaust gas recirculation flow insuff detected,
P0460fuel tank level indicator circuit error.
And I believe I've told everything i know ...
Ford F-150 - 1997-2003 :: Shaking And Idle Bounces Between 500 And 750 - Codes P0172 And P0174
2003 f150 5.4, 4x4 ... Truck is shaking pretty bad, idle bounces between 500 and 750, and its throwing p0172 (rich on bank 1), P0174 (lean on bank 2), and it looks like a misfire on cylinder 8 judging by that power graphy thingy. I'm going to check for a vacuum leak tomorrow on the PCV.
View 2 RepliesFord F-150 - 1997-2003 :: Timing Cover Cracked / Welded - Now Engine Starts Then Shuts Down
I recently removed my timing cover due to a coolant leak and found the cover was cracked. I had it welded and reinstalled but i did not remove the crank sensor from the cover while it was being welded. Now the engine starts but shuts right back down. Do the welding may have damaged the sensor and giving me this condition? 1997 4.2 ....
View 1 RepliesFord F-150 - 1997-2003 :: 2002 Truck Started To Idle Very Rough - Codes PO308 And PO316
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 RepliesGolf IV / Jetta IV :: Revs Just Drop Down To 0 And Engine Shuts Down While Slowing Down
Looking for some hint regarding V6 AUE ? Regardless if engine is warm or cold, sometimes happens to me that during driving, while slowing down and pressing on clutch pedal, revs just drop down to 0 and engine shuts down (vehicle still moving). This usually happens while changing gears from 3rd to 2nd on low speeds in city, or while slowing down to full stop in 2nd gear and pressing clutch pedal.
While this happens, I quickly switch off the ignition and start the engine again, which is tricky and potentially dangerous, since vehicle is still moving but my power steering and brakes are not functioning because of stopped engine.
Some relevant info...I have K&N cone air filter intake and ECU is remapped by BTS Racing (German tuning house).
Car is running and pulling normally. In all other regimes of driving, there are no issues or whatsoever.
Ford F-150 - 1997-2003 :: Got Codes After New Engine?
We sold a customer a 5.4l engine and he installed it and it idles just fine, but falls on its face when put under load. Truck is a 2001 f150 and is not around here. Cus gave me these codes:
P0135
P1130
P0174
P0308
P0351
P0352
P1131
From all I have found, it appears to be a lean condition and cop #1 and #2. All of these codes pop up all at once after r&r ing an engine? I am thinking bad intake gasket and possibly bad coils.
Elantra XD (2001-06) :: 2005 - Slight Erratic Idle / Check Engine Light And Codes
I just purchased a 2005 elantra with 133k on it and she runs fine other than a slight erratic idle. And by slight I mean it will jump about 50-100 rpm idling and every blue moon it will jump up to 250 rpm sitting there. After idling for a while my CEL came on with the following codes.
P0507 idle air control rpm high
P0506 idle air control rpm low
P0170 fuel trim malfunction bank 1
P0121 throttle position sensor
What could be causing this? I took the iac off and cleaned it with maf cleaner but it didn't work.