Ford 7.3L Power Stroke (1999-2003) :: When Push The Clutch To Floor Its Not Disengaging All The Way
In my 99 with a zf6 it seems like when I push the clutch to the floor it's not disengaging all the way. It has a newer valair clutch in it maybe 15000 miles on it. It's really hard to get the truck in reverse or first from a stop. If the truck is stopped and it's in reverse or first with the clutch to the floor it will move in that gear. Is there a adjustment on the clutch? I'm thinking no since its hydraulic....
View 14 RepliesFord F-150 - 1997-2003 :: 4x4 Not Disengaging - Truck Is Stuck In 4Lo
1999 f150 4x4 the wife used my truck and had to use the 4wheel to back the truck up, now the truck is stuck in 4low.
View 10 RepliesFord Ranger / B-Series :: Clutch Pedal Went Almost To The Floor Before Disengaging
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
GTI 337/20th Anniversary :: Clutch Pedal Goes From Being Soft To Very Hard When Close To Disengaging
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 RepliesFord Ranger / B-Series :: 1999 - M5OD Popping Out Of Third Gear Occasionally
My M5OD in my 1999 Ranger 4x4 with 3.0 occasionally pops out of 3rd gear. I think it does it only under light throttle or coasting. Also some vibration, especially in 3rd gear. Once in a while the gears grind when shifting into third. Truck has 145,000 mostly highway miles. Frequent fluid changes with Redline D4ATF.
What could be the cause, bad synchros ? How hard is it to remove the transmission and make a repair for something like this, what kind of special tools, etc. I assume a transmission jack would be real useful, what else would I need other than the normal wrenches and sockets ? Is there a good shop manual recommended for doing this repair ?
Ford F-150 - 1997-2003 :: 2001 - A/C Clutch Not Turning On?
My AC clutch is not turning on. I do not have any AC gauges but if I unplug the compressor and put a meter on the 2 harness pins, I do not see any voltage when truck is running and AC on. I really don't know much about AC but I am thinking the problem may possibly be the low pressure switch or possibly low on freon. How can I check if I am low on freon without gauges? Where exactly is the low pressure switch located on my truck and if I jump the switch and the clutch kicks on, does that tell me that the problem can only be the low pressure switch or low on freon. I'm just trying to work through a few of the gremlins.
View 14 RepliesFord F-150 - 1997-2003 :: AC Compressor Clutch Broke
I have a 01 f150 4.2L and a while ago the ac compressor clutch broke. I didn't catch it in time and the stress it caused on the belt broke the power steering pump pulley. So I replaced the steering pump and pulley and the compressor the accumulator/dryer and the office tube put the 134a back in and everything worked fine. three months later ac stopped working. I figured the condenser was bad so i replaced it. Charged it up still no cold ac. so i thought maybe the manifold that goes on the compressor was clogged so i replaced it. While I did that i said to myself well i should tear out the dash and replace the evap as well. so just about everything has been replaced on the ac system.
Aside from the cycle switch and the high side switch witch from my test both seem to be working. now here is the thing. the tube witch holds the office gets ice cold then goes to the evap but the suction line coming from the evap doesn't get cold and the ac blows warm air. this very problem is what convinced me that the evap was clogged and needed to be changed witch is why i undertook the task of tearing the dash out. in all it took 14 hours to do the whole job. now for the pressures that i get from the ac manifold low side goes 40 down to 20 ..... this is normal. high side is a little high. I charge it to 125 still no cold air. so i dump a little more 134 in. at 90 degrees high side pressure should be around 200ish i get it there still no cold air. I have just about replaced everything i can think of.
Ford F-150 - 1997-2003 :: Shifting Into Reverse - Clutch Not Engaged At All
Just got a 98 f150 yesterday and I noticed last night when I went to shift into reverse, with the clutch all the way to the floor as I tried pulling the shifter back, it sounded like the clutch wasn't engaged at all. Shifting from all the other gears works just fine. Ive found that If the truck is off and I start it in reverse it works just fine.
View 3 RepliesFord F-150 - 1997-2003 :: AC Compressor Clutch Engaging While Heater Is On
soo a friends 03 f-150 w/ the 4.6 has noticed the a/c compressor clutch engaging while heater is on. clutch engages for about 3 seconds or so and kicks back out consistently but only w/ the heater on. a/c dose function property when using a/c functions... Is this normal or does something need serviced???
View 3 RepliesFord F-150 - 1997-2003 :: A/C Clutch Winding Too Much - Bypassing The Pulley?
got the 4.6, AC clutch is just winding like crazy, so Im going to do a cheap fix and jus bypass the pully. Now do I need to remove the compressor or can I just get a belt for a 4.6 without AC and just not use it?
View 1 RepliesFord F-150 - 1997-2003 :: 1999 - Type Of Fan Clutch Fluid?
What type of fan clutch silicone fluid is used in case you need to replace some during removal?(99 ford f150 5.4 vin L)
View 5 RepliesFord F-150 - 1997-2003 :: 1999 - Second Gear Hot - Only Double Clutch?
I have a '99 f150 singlecab xl sport 4.2 2wd 5spd with 139,xxx miles on her. Shes's a good truck, but second gear is shot, I can only get into it by double clutching, and that only sometimes works. I have a couple questions, the first one being what do yall think the problem is. To me and my friends it seems like the syncro mesh. Second, if it is something major, is it even worth saving the truck? I know she isn't worth a ton but I hate to go through the hassle of selling and buying a car.
View 1 RepliesFord F-150 - 1997-2003 :: Fan Clutch And Thermostat Replaced / Need To Burp The System?
I replaced the fan clutch and thermostat on my 1999 5.4. Do I need to "burp" the system or anything?
View 1 RepliesFord F-150 - 1997-2003 :: 1999 - AC Clutch Would Try To Spin But Very Intermittently Now Dead
How can I determine if my compressor is bad or is the solinoid/clutch bad. Truck had sat for about 9 months-1yr. A/C hadn't been operated for an additional 5-6 months. It worked like a freezer before I parked the truck. When i started the truck back up and tried the a/c the clutch would try to spin but very intermittently, now not at all. What direction should I go?
View 9 RepliesFord F-150 - 1997-2003 :: Cruise Control Not Working After Clutch Changed
A few years ago I had the clutch changed on my 1997 F150. Afterwards the cruise control wasn't working. When I brought the truck back to the repair shop I heard the manager tell the mechanic to "attach the clip by the pedal" and that fixed it.
I just had some work done, had to replace the oil pan, and the mechanic had to remove the transmission. Now the cruise control doesn't work. I changed the Pressure switch but it didn't fix the cruise control. What that clip might be that fixed the cruise control last time?
Ford F-150 - 1997-2003 :: New Clutch - Grinding Noise When Putting It Into 1st Gear
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission. I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced. I have also just had a new hydraulic clutch kit installed.......
View 1 RepliesFord F-150 - 1997-2003 :: Rumbling Noise - Rear End Clutch Plates Going?
2000 f150 182000 makes a rumbling noise from rear end mainly when turning at slow speeds. Thought it might of been axle bearings so replaced them this weekend to no avail. I have the 9.75 limited slip rear end but what I found out this weekend is that the axle bearings are for 8.8 , the 9.75 bearings was to big.
So does this mean I have 9.75 ring gear with 8.8 axles ? I have been using royal purple 75-140 with no friction modifier because royal purple says its it there.
But after doing some research Im going to go get some friction modifier and see if it works . So my question is how much of a pain is it to replace the clutch packs? What if I wanted to just put a different differential in and do away with limited slip ? Or go with a different aftermarket limited slip diff. ? what are my options , etc.
Ford F-150 - 1997-2003 :: Overheating - Clutch Fan Not Coming On At High Temps
I am having a problem with the clutch fan not coming on at high temps pulling a grade or flat. Replaced the clutch had the front of the radiator removed and all the debris blown out and replaced the thermostat. Still over heating and the fan comes on real late.
View 1 RepliesFord F-150 - 1997-2003 :: Truck Not Moving In Reverse Like Clutch Is Still Disengaged
My truck was working fine and I drove it to school one day and I was driving and I noticed the RPM was high and the truck wasn't moving correctly luckily I made it home and parked it now it won't move at all I can shift into gears and I put it in first and reverse and let off the clutch and it doesn't move like the clutch is still disengaged. The Slave Cylinder is pressing against the pressure plate to disengage the clutch and then releasing. I have a single cab 1999 Ford F150 4.2 V6.
View 3 Replies