IS F (2008-2014) :: Driver Side Brakes Dragging On The Rotor?
I replaced my front axle pads but the driver's side brakes seem to be dragging on the rotor making a very loud squealing noise when im driving. When I parked it in my driveway it was really hot and smoking. It doesn't happen to the passenger side. I pushed back the Pistons easily to get the brake pads in there so that wasn't a problem. But I must admit I changed them when my brakes were grinding.
View 13 RepliesFord Super Duty (1999-2016) :: Driver Side Front And Rear Brakes Dragging Bad
Truck is 2007 6.0L 4 door F-250 FX4
So this started after some High water encounters around my area. All freshwater. Went to the store and then i notice the truck pulling Left and got home and checked brake temps and the driver front and rear were over 400*F passenger side was 150* or less. No trailer no load in the bed. I decided to clean everything. Pads are worn but still have life.
Rotors showed some signs of where the pad is dragging Not bad though just a small area close to the top hat. I cleaned pads, carriage, and clips and reinstalled everything with some anti seize on the edges of the pads where the clips are and at the same spots on the carriage.
Thought it was ok but the after more water and a day or two sitting the same thing happened again. It is only the drivers side and it's both front and rear. I am stumped on this one. Two calipers going bad at once? I need to tow a boat on Monday So I have got to fix this.
Ford Super Duty (1999-2016) :: Rear Brakes Sticking / Driver Side Rotor Glowing Red
Took the truck out the other night, got to town felt the slight drag but nothing alarming, got out of the truck and could smell it, rear drivers side rotor glowing red, pass side not glowing, pressed park brake then released, driver side freed on its own, pass side sticking, replaced pass side rotor and pads, found nothing out of the ordinary... Ford F250 4x4, 2005 ....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: How To Remove Driver Side Rear Rotor
I noticed my rear brake smoking on the truck really just the rear driver side. I had replaced the pads and caliper and rotor a very long time ago. What I think happened is the parking brake got hung up somehow. The wheel was extremely warm and the reason I noticed it was not only the smoke but I felt some sort of wobble or almost out of alignment issue.
When I got home I noticed the smoke and extreme heat. I removed the caliper and the pads look still "new" and evenly worn. I did bleed the caliper just to make sure no air, I even put a spacer in the caliper and my wife applied the brake and they closed appropriately. Then I was trying to get the rotor off and no success. I did adjust the parking brake but I am not sure if you move it up or down to loosen it up?
I have used PB Blaster to try and loosen it up, rubber mallet while I turn it (although it does not turn easily at all), I sprayed it inside where the adjuster is hoping it would seep down between the shoes and the hub. I heated the hub up with a little torch - no success. I was thinking of using a wood piece as a butter and hammer from the inside out on the rotor but fear that will warm the rotor itself.
Ford Brakes/Suspension :: 1999 F350 - Brake Shoes Contacting Rotor (dragging) When Engine Is Off
I changed over to summer tires today on my 1999 4wd F350 diesel . While the front tires were off of the ground, I tried rotating the wheels by hand to see what the resistance was like. I was surprised at how stiff they were. It would take three fingers to rotate the wheel and as soon as I stopped applying pressure the wheel stopped turning. I pulled the rims off and found that the calipers appeared to be contacting the rotors and causing resistance.
My last rig was a 1960s 4wd F250 that had calipers that could be adjusted manually. I kept these adjusted so the calipers were almost touching the rotors. I could spin the rims with one finger and the wheel would turn for 30 seconds or so until coming to a stop. Is this normal?
Ford F-150 - 1997-2003 :: Brakes Dragging And ABS Light On
I have a 1999 ford f150 with 4.2 and 156,000 miles, about a month ago I drove from my house to a friends house a few hrs away. On my way home I started smelling a burning smell and stopped and my brakes were smoking. So I replaced brake calipers and still they drug then I changed brake lines and I can still only drive a few miles with out them getting really hot and dragging....
View 9 RepliesFord F-150 - 1997-2003 :: Hot Drums And Brakes Dragging On Takeoff
My husband bought a 1997 Ford F150 and the seller said he changed the brake lines, but the back brakes have dragged on takeoff since he bought it. Just put new shoes on it and it's still doing the same thing, but now the drums are getting hot. Is it possible that the seller got the brake line backwards and that might make the back brakes drag?
View 2 RepliesFord Brakes/Suspension :: 1997 F350 - Driver Side Rear Brake Hot
Last weekend I did a rear brake job on my 1997 F350 4wd diesel. I replaced the shoes, replaced all the hardware, replaced the cylinders and had the drums turned. I have driven the truck all week and everything has been fine. Tonight while out of town I set the parking brake to see if it was any better since the rebuild, and it was. Shortly after releasing the parking brake I drove about an hour to get home. When I arrived home by driver side rear brake, wheel, etc. was very hot. I threw water on it and it turned to steam instantly.
I suspect that setting my parking braked hard like I did (like you're suppose to) somehow caused it to drag. What is causing this and what needs to be done so that it doesn't happen again?
After reading some other posts I went out and checked my parking brake cable and found that it is not bound up that I can tell. Perhaps it did not completely release although it seems to release just like the other side. I checked it from front to equalizing bar and it is in great shape. The plastic coating is still on the wire and there isn't any corrosion the entire length. The only thing I did differently on this trip vs the one I made two days ago was try out the parking brake before I left. The last trip I could barely feel any heat on the rear wheels when I got home, this time the driver side was scorching hot.
Ford F-150 - 1997-2003 :: 1999 4x4 Lariat - Both Front Brakes Dragging?
I have a 99 f150 4x4 that has done this twice, once last year and once this year during hot (90+) weather. I'll notice the vehicle seems like it doesn't want to go. Park overnight and it will work ok. Last time it happened the other day I stopped at wally world and both front wheels were real hot and I could smell the brakes. Came out hour later and when I pushed the brake pedal to put it in gear the pedal went to the floor.
Pumped up pedal and drove off but truck would barely move, drove 10 mph to a buddy of mines shop and it sat overnight and worked perfect the next day. He inspected everything and seems to think it might be the abs control unit. He noticed a small amount of fluid had come out of the unit and dripped on the ground. Also no abs light or brake light has ever come on
Ford F-150 - 1997-2003 :: 1999 - Front Brakes Dragging / Sticky Caliper
Bought a high mileage 99 f150 4x4 yesterday. In the process of cleaning her up, the water hose hit the disc brakes on the drivers side and it was hotter than a BBQ grill! Ok, immediately I thought this isn't good. Jacked her up and pulled the caliper. Pads were almost gone so replaced them with a new set, went for a drive. Now the damn things were smoking so bad I thought they were gonna catch fire! Sticky caliper , right? Stopped and got one then realized that the passenger side started doing it too.
Another trip for the other caliper and new pads because these were toast. I mean just burnt to hell. Before I started working on the truck again, I checked on here and I'll be darned if I didn't find out that the old brake hoses might be acting like a check valve because of rust and deterioration. Got a set of brakes hoses too. Put everything on this morning and works like a charm.
1999 4.6 XL
Passenger side done
Ford F-150 - 1997-2003 :: Front Brakes Dragging Only In Prolonged Stop And Go Traffic With Hot Ambient Temps
On a 1998 F150 2 wheel drive 4.6 250k, the front brakes will drag under a specific set of circumstances; only in prolonged stop and go traffic with hot ambient temps. Rotors, calipers, rear shoes, drums, fluid, bearings, seals have all been replaced. This occurs only a couple of times a year, otherwise the brakes work perfectly. It starts out as a slight shimmy that worsens until you can smell the pads cooking and the wheels are hotter than hell. The truck will hardly move at times. The rears are normal. After the truck cools for hours, no symptoms.
View 7 RepliesTouareg :: Driver Side Rear Brake Dragging Hard
So, I just returned home from a 7-day caribbean cruise to find my drivers side rear brake dragging...hard. I know it can happen to any car but it's aggravating none the less. I guess I'll limp the 2 miles to the dealer on Monday morning...
View 2 RepliesFord F-150 - 1997-2003 :: Grinding Sound From Driver Side Rear Of Truck
Driving home yesterday I noticed a grinding sound from the driver side rear of the truck. Had a look at the drum brake today and found that the cable to the adjusting lever had snapped and pieces had jammed making the grinding noise. I need to replace the cable and probably have that drum surfaced, but the pads look good.
On the passenger side the hardware is all intact but the shoes look as if they have "spider" cracks everywhere, still lots of shoe left though. What might be causing the cracks on the shoes, and do these need to be replaced? How to do rear drum brakes? (1997 4x4)
Ford Super Duty (1999-2016) :: 2003 F250 5.4L - Axle Leaking On Passenger Side Rear Rotor And All Over
Here's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
Ford Brakes/Suspension :: 2003 F350 - All 4 Brakes Dragging
Here's the deal:
* Drive the truck after it's been sitting a while (overnight, or at least a couple of hours), everything's fine. Good brake pedal feel.
* Drive 10-15 miles, stop-and-go at lights and stop signs, the brake pedal slowly goes from normal to firm, to very firm. Then, no play whatsoever and brakes are dragging bad. Yesterday, they were dragging so bad that I had it pulled into 1st gear with pedal on the floor just to get thru an intersection.
* Get out and check each wheel, all 4 brakes are dragging. I can tell from the heat pouring out of each wheel. And I've verified with infrared thermometer. Also, I've raised the vehicle when this is happening, and all 4 wheels will not turn. So it's definitely all 4 brakes.
At first, I assumed it was seized slide pins. But I've THOROUGHLY cleaned each and every one, and lubed with synthetic caliper grease. When the brakes are feeling normal, I've had my wife pump the brakes while I watched the calipers. Near as I can tell, they slide easily. Again, when my problem happens, it's all 4 wheels SIMULTANEOUSLY. So I've pretty much ruled out slide pins.
The brake pedal itself isn't getting bound by anything. It moves freely and I've lubed each of the pivot points. No problems there.
* When the brakes are dragging, I can crack the bleed screws and some fluid will come out at each wheel, which releases the brake at that wheel and I can then turn each wheel freely. So, there's residual pressure in the lines. I replaced the master cylinder (twice actually). No change in behavior.
BTW: I thoroughly bled the lines after each of the two master cylinder changes. I must've put 60+ ounces of fresh/clean/new fluid into the system so this isn't related to old fluid.
* Next, when the brakes are dragging, I can unscrew the master cylinder about 1/8-inch or so from the booster, and the brakes immediately release. Again, indicating residual pressure in the lines. So, I assume that something funky is going on with the brake booster. Also, when the brakes are dragging, I can pull the vacuum hose from the brake booster. And after a few seconds the brakes release. So I installed a new brake booster (re-manufactured one from NAPA -- they didn't offer a brand new one). No change in behavior.
After swapping the brake booster, I can still pull the vacuum tube when the brakes are dragging and it'll release in just a few seconds. So, it really seems like something is going on with the booster, but I can't figure out what it might be.
It is possible for the brake booster vacuum tube to have TOO MUCH vacuum, thereby causing the brakes to be unknowingly applied? Is there maybe a regulating valve of some kind in the line?
Ford F-150 - 1997-2003 :: 1999 - Cabin Water Leak - Small Puddle In Driver Side Rear Floor Corner
My 1999 F150 Supercab has developed a water leak which I would like to ask your opinions on. Parked on a 20 degree incline during a pouring rain yesterday, I came out to find a small puddle in the driver's side rear floor corner and about an ounce of water pooled in a little lip at the bottom of the rear window in the right corner of the window! Haven't started tearing anything apart yet (and might not be able to myself), but it seems that it is possibly the rear window seal as the window and the outside body area appear to be in good shape otherwise (no visible rust, no seal obviously dislocated, etc).
Also, don't know if it's related, the other day I jacked up the truck with a floor jack under the front crossmember but a bit off center which caused the truck to twist a bit before both wheels came off the ground. While doing this, I heard and felt a loud bang like something broke in the frame! Couldn't see anything out of place and something similar has happened before where a lug of the jack cup had shifted slightly while jacking the vehicle and it caused a loud bang to be heard, but this time it didn't quite feel like it was at the jack but further back.
Could something have "broken" in the truck that I can't quite see and thus this leak has occurred which wasn't there previously or could it just be coincidence that the bang and leak occurred so close in time to each other. I know it's hard to diagnose something like this without seeing the vehicle or really know what happened but I just had to put it out there as part of the events that occurred within the timeline for this leak.
Ford Brakes/Suspension :: 2007 Expedition - Rear Rotor Removal
I need to change the rear brake pads on a 2007 Expedition and was going to turn the rotors also. It appears the rotor is held onto the axle by a large nut and not having done any brake jobs in several years, I've never run into a rear rotor that's bolted on. Is this the case and if so, what size socket do I need to get it off. Also, I was curious if there is anything else I need to know before I dive in. I heard it was difficult to get off.
View 7 RepliesFord F-150 - 1997-2003 :: Clunking Sounds Coming From The Rear End
Was having some clunking sounds coming from the rear end on the old F150. Bro in law said it was lack of gear lube and the rear diff grinding from the start. Wasn't the issue. U - joints are shot and causing the issue. My question is I marked the drive shashshaft and flange with a sharpie but it rubbed off on the flange from free spinning the rear end seeing if the issue was there. From the drive shashshaft to the rear diff flange does the flange need to be marked or no? I did scribe with a nail the transfer case and marked the drive shaft with sharpie. So is the flange being marked important or just the bracket with the u-joint? Would've used soap stone but don't have any on hand.
View 5 RepliesPrius (Gen 2) :: Sounds Coming From Rear Driver Side Happens When Accelerated Or Turn
I'm driving home today and all of a sudden my car is making noises. I can't really explain what it is, but it sounds like it is coming from the the rear driver's side and happens when I accelerated or turn. I know that isn't much of an explanation, but my car has been fine then just all of a sudden?
View 3 Replies