Ford F-150 - 1997-2003 :: Hot Drums And Brakes Dragging On Takeoff
My husband bought a 1997 Ford F150 and the seller said he changed the brake lines, but the back brakes have dragged on takeoff since he bought it. Just put new shoes on it and it's still doing the same thing, but now the drums are getting hot. Is it possible that the seller got the brake line backwards and that might make the back brakes drag?
View 2 RepliesFord F-150 - 1997-2003 :: 1999 4x4 Lariat - Both Front Brakes Dragging?
I have a 99 f150 4x4 that has done this twice, once last year and once this year during hot (90+) weather. I'll notice the vehicle seems like it doesn't want to go. Park overnight and it will work ok. Last time it happened the other day I stopped at wally world and both front wheels were real hot and I could smell the brakes. Came out hour later and when I pushed the brake pedal to put it in gear the pedal went to the floor.
Pumped up pedal and drove off but truck would barely move, drove 10 mph to a buddy of mines shop and it sat overnight and worked perfect the next day. He inspected everything and seems to think it might be the abs control unit. He noticed a small amount of fluid had come out of the unit and dripped on the ground. Also no abs light or brake light has ever come on
Ford F-150 - 1997-2003 :: 1999 - Front Brakes Dragging / Sticky Caliper
Bought a high mileage 99 f150 4x4 yesterday. In the process of cleaning her up, the water hose hit the disc brakes on the drivers side and it was hotter than a BBQ grill! Ok, immediately I thought this isn't good. Jacked her up and pulled the caliper. Pads were almost gone so replaced them with a new set, went for a drive. Now the damn things were smoking so bad I thought they were gonna catch fire! Sticky caliper , right? Stopped and got one then realized that the passenger side started doing it too.
Another trip for the other caliper and new pads because these were toast. I mean just burnt to hell. Before I started working on the truck again, I checked on here and I'll be darned if I didn't find out that the old brake hoses might be acting like a check valve because of rust and deterioration. Got a set of brakes hoses too. Put everything on this morning and works like a charm.
1999 4.6 XL
Passenger side done
Ford F-150 - 1997-2003 :: Driver Side Rear Sounds Like Brakes Are Dragging Against The Rotor
Went and got new tires on the supercrew. Went going through parking lots or simply driving i hear a loud squeal like brake pad squeal. I put brand new wagner ceramics on the truck. Also if i turn to the left the driver side rear sounds like brakes are dragging against the rotor. Whats goin on with this. The squeal will happen between 10 mph to 20 mph and the grinding noise will happen if I am cruising or turning to the left. It goes away when i apply the brakes.
View 1 RepliesFord F-150 - 1997-2003 :: Front Brakes Dragging Only In Prolonged Stop And Go Traffic With Hot Ambient Temps
On a 1998 F150 2 wheel drive 4.6 250k, the front brakes will drag under a specific set of circumstances; only in prolonged stop and go traffic with hot ambient temps. Rotors, calipers, rear shoes, drums, fluid, bearings, seals have all been replaced. This occurs only a couple of times a year, otherwise the brakes work perfectly. It starts out as a slight shimmy that worsens until you can smell the pads cooking and the wheels are hotter than hell. The truck will hardly move at times. The rears are normal. After the truck cools for hours, no symptoms.
View 7 RepliesFord Brakes/Suspension :: 2003 F350 - All 4 Brakes Dragging
Here's the deal:
* Drive the truck after it's been sitting a while (overnight, or at least a couple of hours), everything's fine. Good brake pedal feel.
* Drive 10-15 miles, stop-and-go at lights and stop signs, the brake pedal slowly goes from normal to firm, to very firm. Then, no play whatsoever and brakes are dragging bad. Yesterday, they were dragging so bad that I had it pulled into 1st gear with pedal on the floor just to get thru an intersection.
* Get out and check each wheel, all 4 brakes are dragging. I can tell from the heat pouring out of each wheel. And I've verified with infrared thermometer. Also, I've raised the vehicle when this is happening, and all 4 wheels will not turn. So it's definitely all 4 brakes.
At first, I assumed it was seized slide pins. But I've THOROUGHLY cleaned each and every one, and lubed with synthetic caliper grease. When the brakes are feeling normal, I've had my wife pump the brakes while I watched the calipers. Near as I can tell, they slide easily. Again, when my problem happens, it's all 4 wheels SIMULTANEOUSLY. So I've pretty much ruled out slide pins.
The brake pedal itself isn't getting bound by anything. It moves freely and I've lubed each of the pivot points. No problems there.
* When the brakes are dragging, I can crack the bleed screws and some fluid will come out at each wheel, which releases the brake at that wheel and I can then turn each wheel freely. So, there's residual pressure in the lines. I replaced the master cylinder (twice actually). No change in behavior.
BTW: I thoroughly bled the lines after each of the two master cylinder changes. I must've put 60+ ounces of fresh/clean/new fluid into the system so this isn't related to old fluid.
* Next, when the brakes are dragging, I can unscrew the master cylinder about 1/8-inch or so from the booster, and the brakes immediately release. Again, indicating residual pressure in the lines. So, I assume that something funky is going on with the brake booster. Also, when the brakes are dragging, I can pull the vacuum hose from the brake booster. And after a few seconds the brakes release. So I installed a new brake booster (re-manufactured one from NAPA -- they didn't offer a brand new one). No change in behavior.
After swapping the brake booster, I can still pull the vacuum tube when the brakes are dragging and it'll release in just a few seconds. So, it really seems like something is going on with the booster, but I can't figure out what it might be.
It is possible for the brake booster vacuum tube to have TOO MUCH vacuum, thereby causing the brakes to be unknowingly applied? Is there maybe a regulating valve of some kind in the line?
Santa FE SM (2001-06) :: 2003 V6 Front Brakes Dragging
2003 Santa Fe 3.6 V6 with ABS
The car sat virtually driven for a year before it was given to me. After 2 weeks of normal driving this past December, the power brakes completely went out. Had to drive the pedal to the floor to stop at even slow speeds. Took the mechanic and they replaced the Master Cylinder and both brake lines.
Shortly thereafter had an unrelated issue with a coilpack gone bad. Replaced coilpack and at that time replaced both sets of brake pads on the rear.
In January, started noticing grinding metal on metal from both front brakes. Took the mechanic and they replaced both calipers, rotors, and pads.
2 weeks or so later, after 10 minutes of driving the front brakes started dragging. The pedal would become extremely hard, and I could notice thew smell of the pads burning. Would have to pull over, put the car in park and pump the brakes to get the calipers to release. This would occur intermittently every few days. Pumping the brakes would always solve the problem.
Over time, the issue became worse, ocurring far more frequently. Around this time I noticed leaving the engine on in park while pumping the brakes would no longer solve the issue. I would have to completely turn the car off and pump the brakes to get them to release.
Started noticing around this same time that the left rear started grinding. The brake pads completely wore down in 3 months time. Too to the mechanic. Replaced caliper, rotor and pads.
Still having the same issue with the brakes dragging. One mechanic thought it could be ABS related and advised me to pull the fuse and the two breakers to diagnose. Still had the same issue, so put the fuse and breakers back in.
No mechanic seems to know what is going on with it, and I'd hate to have to replace all the brakes again as the problem goes untreated. Is it possible that the master cylinder or brake booster could be the issue? It's a brand new master but that doesn't necessarily mean anything, I'm told. Again, I can only get the brakes to release the pressure by pumping the pedal with the engine off.
Ford Brakes/Suspension :: Front Brakes Are Dragging / Does Not Stop The Truck Just Gets Hot
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 RepliesFord F-150 - 1997-2003 :: Intermittent Grinding / Dragging Noise Coming From Pulley
1997 4.6L.. Have an intermittent grinding / dragging noise coming from the pulley (?timing) area that I'm trying to pin down. Both the alternator and tensioner were replaced prior to the noise starting. The ac compressor and the power steering pump are original. The fan clutch was replaced about 4 years ago and the water pump 8 years ago. Timing chain / guides / tensioner are all original.
I don't notice any of the common ps pump indicators (whine increase when steering) but noticed the fluid level was down slightly and that the pulley seems to have some inward - outward play with the belt off. I also don't have any other engine symptoms like rough idle or any codes being triggered. How to isolate the culprit?
Ford F-150 - 1997-2003 :: ABS Light Came On Then Off / Brakes Will Grab
I have an ABS light that likes to come on and off. My rear tires lock up when I come to a stop. Stopping sometimes takes longer distances. Other times I can barely touch the brakes and they'll grab real fast and then become soft immediately. Every time I hit the brakes is different I never know what to expect. There's usually a real long Rea of play in the pedal. As in I push it about half way down then the brakes with grab. Other times I barely put my foot on it and it jerks the truck but then loosens back up and comes to a (normal for the truck) stop. What could this be? 1997 4.6 4x4 f150
View 2 RepliesFord F-150 - 1997-2003 :: Pedal Was Rock Hard When Hit The Brakes Coming To A Stop Light
I have a 1997 F250LD 4WD. I was driving and came to a stop light. I hit the brakes and the pedal was rock hard with what seemed to be very little travel. I pushed hard to get to a stop and the abs activated and I came to a slow stop. This has happened about 3 times over the last 1000 miles of driving. I see no ABS or Engine lights. Most of the time the brakes are normal. Pads are fine, fluid is fine. Brake booster seems to work fine, pedal is not mushy or hard to press other than the 3 or so times this has happened. Once this happens I can let off the brake and everything is normal. I have not found any vacuum leaks.
View 6 RepliesFord - Clubwagon :: 1998 - Front Brakes Sticking / Van Dragging To Keep Moving
1998 FORD E350 CLUB WAGON 15 PASSENGER VAN. Front brakes are sticking bad. Stop at intersection with snow or slick condition and you can barely get the van to start moving. After you do you can fell the drag and the vehicle working hard to keep moving. Take tires off front, can not see anything obvious that is wrong. Can see where the bake pads are leave makes on the rotor.
View 4 RepliesFord F-150 (2009-2014) :: 2013 - Brakes Are Grinding And Squealing Bad / Dragging?
2013 Platinum. See sig for details. 37,000 miles. 1 owner. Truck has been basically parked since June. However I take it out for a quick spin every 3 week for 10 miles or so. Currently has storage insurance on it.
When backing out of the garage the brakes are grinding and squealing bad. Also getting feedback through the steering wheel for the first couple miles which leads me to believe it's one or both the front brakes.
Ford F-150 (2009-2014) :: 2012 - Brakes Dragging - Noise / Hum At Slower Speeds
I have a 2012 F-150 4x4 super crew all factory with 54,000 mi. I've noticed a new noise/hum at slower speeds, more frequent now. The noise doesn't sound like its from the front or back specifically. I pulled the front wheels this evening and the front rotors seem pretty tight, how easily should they turn with vehicle off for about 30 min? I started it and pushed and released the brake and quickly tried to turn them, very tight, after a minute or two they relaxed a little, another 5 min they seemed tighter? I sharpie mark on both inside and outside of the rotor and turned it past the pads and they are both squeezing equally ruling out binding of the slider bolts.
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F550 - Brakes Dragging / Won't Roll When Out Of Gear
The brakes seam to be dragging on my F550.It won't roll when out of gear. Noticed a good deal of brake dust on all 4 corners after just a couple hundred miles. Also,when it does roll I can some times hear it creak slightly. At not time does it lose any braking action nor does the brake pedal get hard or soft.I know it will need pads and rotors soon since the rotors are pretty grooved. (Just bought the truck last month....it's on my LOOOOONG to do list.....).
View 3 RepliesFord Super Duty (1999-2016) :: Driver Side Front And Rear Brakes Dragging Bad
Truck is 2007 6.0L 4 door F-250 FX4
So this started after some High water encounters around my area. All freshwater. Went to the store and then i notice the truck pulling Left and got home and checked brake temps and the driver front and rear were over 400*F passenger side was 150* or less. No trailer no load in the bed. I decided to clean everything. Pads are worn but still have life.
Rotors showed some signs of where the pad is dragging Not bad though just a small area close to the top hat. I cleaned pads, carriage, and clips and reinstalled everything with some anti seize on the edges of the pads where the clips are and at the same spots on the carriage.
Thought it was ok but the after more water and a day or two sitting the same thing happened again. It is only the drivers side and it's both front and rear. I am stumped on this one. Two calipers going bad at once? I need to tow a boat on Monday So I have got to fix this.
Ford Brakes/Suspension :: 1999 F350 - Brake Shoes Contacting Rotor (dragging) When Engine Is Off
I changed over to summer tires today on my 1999 4wd F350 diesel . While the front tires were off of the ground, I tried rotating the wheels by hand to see what the resistance was like. I was surprised at how stiff they were. It would take three fingers to rotate the wheel and as soon as I stopped applying pressure the wheel stopped turning. I pulled the rims off and found that the calipers appeared to be contacting the rotors and causing resistance.
My last rig was a 1960s 4wd F250 that had calipers that could be adjusted manually. I kept these adjusted so the calipers were almost touching the rotors. I could spin the rims with one finger and the wheel would turn for 30 seconds or so until coming to a stop. Is this normal?
Toyota - Sienna :: 2000 - Front Brakes Dragging?
The front brakes on my 2000 Toyota Sienna are dragging occasionally. I have replaced the front calipers (one of them twice), the master cylinder, and the ABS unit (with a junk yard unit). I have also shortened the master cylinder push rod to see if that would make a difference. The brakes still drag occasionally as indicated by the front hubs becoming excessively hot.
View 9 RepliesIS F (2008-2014) :: Driver Side Brakes Dragging On The Rotor?
I replaced my front axle pads but the driver's side brakes seem to be dragging on the rotor making a very loud squealing noise when im driving. When I parked it in my driveway it was really hot and smoking. It doesn't happen to the passenger side. I pushed back the Pistons easily to get the brake pads in there so that wasn't a problem. But I must admit I changed them when my brakes were grinding.
View 13 Replies