Ford 7.3L Power Stroke (1999-2003) :: Truck Does Not Start Without The Clutch Pushed In - Cruise Intermittent
I've tried everything I can think of to get my cruise control working again to no avail. I have a late 99 with a 6 speed. So far I have checked all the fuses with a multimeter, I've checked continuity from the harness under the dash through the clockspring to the switches, truck does not start without the clutch pushed in so the neutral safety switch works, has the upgraded switch and harness off the master cylinder. the previous owner said the cruise was intermittent about a year after they did the harness and switch recall on it. is there a way to test the harness and switch? I got a 1800 mile round trip coming up in about a week and I am gonna have a sore foot if I cant figure this out.
View 11 RepliesFord Ranger / B-Series :: 1989 Truck Jerked Really Hard - Lurch When Clutch All The Way Pushed Down
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
Ford F-150 - 1997-2003 :: Truck Not Moving In Reverse Like Clutch Is Still Disengaged
My truck was working fine and I drove it to school one day and I was driving and I noticed the RPM was high and the truck wasn't moving correctly luckily I made it home and parked it now it won't move at all I can shift into gears and I put it in first and reverse and let off the clutch and it doesn't move like the clutch is still disengaged. The Slave Cylinder is pressing against the pressure plate to disengage the clutch and then releasing. I have a single cab 1999 Ford F150 4.2 V6.
View 3 RepliesFord F-150 - 1997-2003 :: AC Clutch Harness Causing Truck To Not Start
My issue started as simply a lack of air conditioning. Upon initial inspection I noticed that the compressor clutch is not engaging when I turn the ac on. So I figured the next step would be to see if I am getting voltage to the clutch. My Chilton book says to test this with the truck on, so I disconnected the harness from the compressor, attached my meter to the cable, and attempted to start my truck. I've found that the truck wont start with this cable disconnected. It will turn over but just never starts. Also the fuel pump comes on as it should.
I've repeated this several times. It always starts with no problem when the compressor clutch is connected. I understand that there is some monitoring circuit with the pcm so maybe that has something to do with it but I'm pretty fuzzy on how that works. Upon further inspection, it looks like I should be able to test my ac signal with the engine off, so maybe that's not such a big deal, but this whole truck not starting business is blowing my mind.
Ford F-150 - 1997-2003 :: Truck Bucks Wildly Either In 1st Or Reverse When Feather The Clutch
97 F150 4.9 200xxx 5 Speed .....
I'm having an issue with my truck. It only seems to happen during warm 80+ weather. In the mornings, and during colder weather, the truck runs perfectly.
My problem is; Every time I go to get going and feather the clutch, either in 1st or reverse, my truck bucks wildly.
I changed the plug wires about 500 miles ago, and am about 4000 miles on a rebuilt engine (plugs as well) and new clutch/resurfaced flywheel. The clutch reservoir is full and I haven't noticed any leaks. There have been no codes thrown.
Could it be a possible fuel problem? I think I changed the fuel filter about 7k-10k miles ago.
I was also wondering if the Gotts mod could be causing it. I did the mod during the winter time, and this is my first summer with it on. My air filter is fine.
Ford F-150 - 1997-2003 :: 1999 - Second Gear Hot - Only Double Clutch?
I have a '99 f150 singlecab xl sport 4.2 2wd 5spd with 139,xxx miles on her. Shes's a good truck, but second gear is shot, I can only get into it by double clutching, and that only sometimes works. I have a couple questions, the first one being what do yall think the problem is. To me and my friends it seems like the syncro mesh. Second, if it is something major, is it even worth saving the truck? I know she isn't worth a ton but I hate to go through the hassle of selling and buying a car.
View 1 RepliesAcura - Legend :: Sticky Clutch - Pushed Pedal And It Would Not Return Or Allow Gear To Engage
1988 Acura Legend, 2.7L 6 cyl., 181,000 miles only do 6,500 miles a year to train station, parked inside, runs great. Last week parked out in hot sun, '90s, for 8 hours. At first, no problem. When did errand and returned to car, pushed clutch pedal and it would not return or allow gear to engage. "Jammed" into 1st, then could not shift, shifted slightly by pulling up on clutch pedal with my foot. Parked overnight, cool, next morning seemed to be fine and crept to mechanic. Mechanic road tested and found no problem and now seems to be working okay. Would parking in sun, high heat cause "clutch cylinder" to "seize" or "freeze"? Is there a "fix"? Also, increasingly hard to get parts for this car.
View 6 RepliesFord F-150 - 1997-2003 :: New Clutch - Grinding Noise When Putting It Into 1st Gear
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission. I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced. I have also just had a new hydraulic clutch kit installed.......
View 1 RepliesFord F-150 - 1997-2003 :: 2001 - Shaking In 1st Gear When Try To Release The Clutch Slowly
I have a 2001 ford f150 4x4 xlt and it seems to be shaking violently in first gear when I try to release the clutch slowly. The person i bought it from said he had a new clutch put in this year So i don't think its the clutch. What could be the cause of it before I take it in to be checked.
View 2 RepliesFord F-150 - 1997-2003 :: Truck Stalls Out In Gear But Not In Park
I had what I was told was the breather (on the drivers side valve cover) snap off. I was able to place a piece of tubing In it and reconnect it. I had to change the #7 cylinder spark plug wire. Got a misfire code and found the wire was loose and corroded. Replaced wire and PVC valve.
My problem is, it seems not to be idling as fast as it was before this happened. The truck stalls out now in gear but not in park. 1997 F150 4.6 ....
Ford F-150 - 1997-2003 :: Truck Stumbles - RPMs Drop When In Gear
I have a 1997 forkd F150 with a 4.6L Romeo engine. I have recently rebuilt the engine and now since it is put back together I am having a issues that i cannot pin point. When the truck is running and in gear my RPM drop to around 500 or below and my oil pressure drops and comes back up when the rpm's come back up this an intermittent problem and I have replaced the IAC valve and every once in a while i get a P0401 code for the exhaust recirculation. I think I am loosing some kind of vacuum. It was not doing this when I tore into the truck. It seems to be running okay not hesitation.
View 2 RepliesFord Transmission :: 2003 F150 - Difficult To Put In First Gear / Little Grind Or Thump?
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
Ford F-150 - 1997-2003 :: Truck Dies At Stop While In Gear - Code P0443
I have a 1997 Ford F-150 with the 4.6L auto trans 189,000 miles
Ok.. there was no problems until the other day when I unplugged the positive side of the battery to replace it's clamp. I Put the new one on and drove to the store but when I came to a stop, the rpm's dropped to 0 and the truck died. I restarted it and every time I would come to a stop it would die unless I give it a little gas also if I start the truck and leave it in park it idles fine until I give it some gas then let off.. the idle drops and dies! If I give it a little steady gas the idle will return to normal.
The check engine light works fine but never once lit up because of this problem! I used a code scanner and if the truck was off and the key forward, it would have no codes. With it running it had the code P0443. I found and replaced a blown fuse and still have the same problem but it reads no codes at anytime. I checked all the vacuum hoses and there seems to be no leaks and the mass airflow sensor looks clean. I have allot of miles but it has been taken care of well and has had a ton of parts replaced over the last few years.
I am wondering why this happened out of the blue and If there is something I am missing that I should be looking at. I don't want to replace the purge control valve if thats not the problem.
Ford F-150 - 1997-2003 :: 1999 Truck Only Drives In 2nd Gear After Hitting Mud Puddle
1999 f150 5.4 it's been over 3 months since It happened I hit a pretty big mud hole and right after it starts bogging and running rough and won't drive I made it home and second and I've been driving it around town in second gear since. I've been trying different things since it happened, It runs rough in drive, reverse, neutral, and first (towing gear) but revs up just fine in second (towing gear).
So far I've
- Checked all fuses
- Changed plugs checks coil packs
- Dropped pan changed tranny fluid and filter
I broke a heater core line so I replaced the intake manifold and got a good look at everything and cleaned it out
- Cleaned throttle body
- Checked all connections
- Checked all vacuum hoses
- Replaced maf sensor
- Pulled the codes but I don't have them handy.
GTI 337/20th Anniversary :: 2003 - Zero Resistance When Clutch Pedal Pushed
My clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
Ford F-150 - 1997-2003 :: Slight Grind And Hesitation When Trans Shift Into Second
I have a 2003 screw 4x2 with the 4.6, 148,000 miles, and I'm not sure what kind of transmission. Recently when the truck would shift into second it would hesitate and I would feel a slight grind, but it only did it when it would shift at 2000 rpm, if it shifted at 2500 rpm it would shift fine. I checked the fluid level, it was full, it smelled okay, looked *fine.
After pulling a boat (19 foot bass boat...nothing too heavy) it started to shake violently when I'd take off from a red light. So I dropped the pan and changed the filter, The fluid was dark red and smelled a little burnt. I put 4qts of fluid in it along with some Lucas transmission fix. The shake during take off is gone, and the grinding while shifting into second got a lot better but didn't go away completely.
However, now the grinding into second has has gotten worse again, and if I make a right turn from a red light it grinds and feels like its slipping until it shifts. I am not sure why making a right turn would affect it but its definitely worse when i turn right, left turns are fine. I'm guessing my transmission is going out and I just need to get it rebuilt...
Ford F-150 - 1997-2003 :: 2000 F350 - Loud Pop And Then Grinding / Brakes Locked Up When Pushed On
I am having a major issue with my truck. I replaced all of my brakes about 8 months ago. Replaced everything. Rotors, calipers, pads etc. About 3 weeks ago I pushed on the brakes and they locked up and I heard a loud pop and then grinding. I pulled my wheel and my brake on the right rear had broke the 2 mounting bolts and fell off. So I put the brake back on thinking I hadn't tightened the bolts.
Drove about 7 miles and around the 10th time I stepped on my brakes it did the same thing. So I replaced the brakes again. Calipers caliper mount and pads. I have been driving it 2 weeks and all of a sudden same thing happened. I push on the brakes the right rear locked up and snapped the bolts again. So now I replaced everything rotor calipers etc. Greased everything up and no problems for a day. Do I need to replace the brake mount and where do I get that?
Ford - F250 :: 1992 - Truck Will Shudder While Let Out The Clutch In First Gear
They are about my F250. It is a 92 with 186000 miles. I love this truck.
After a long trip, maybe 1.5 hours, the truck will shudder while I let out the clutch in first gear. This only occurs in first, and it doesn't happen after the truck sits for a bit, just after driving.
I have an opportunity for a good deal on a F150. It is a 2001 with 181,000 miles for $4000. Is it worth updating for the new technology even if there is the same old high mileage issue?
Ford Transmission :: No Clutch / Truck Will Not Engage A Gear While Running
I have a 2001 m5r2 ford f-150 standard transmission. i have replaced the slave cyl., the entire clutch assy., the master cyl. pilot bearing. the trans. will engage all five gears plus reverse while truck is off but will not engage a gear while running. i have bled and bled and bled and still will not engage.
View 1 Replies