Ford F-150 - 1997-2003 :: Throwing Code P0171 And P0174?
97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
Ford F-150 - 1997-2003 :: Truck Won't Start / Code P0174 Keeps Coming Back
I have a 2001 F150 XLT Supercab,4.2lt, automatic, 2WD.
I was able to start it about a month or so ago but it was really hard to start. I had to use starting fluid to get it started, and it was still tough to get it to start, but once started and warmed up it ran fine.
Now I tried to start it again and it kicks over and wont start. I tried the same with the starting fluid and it almost starts and dies. I think I used a little too much starting fluid because after a while of trying and spraying starting fluid, I got a hard backfire that sounded like a shotgun that was strong enough to pop off the MAF Sensor and throw it about 10 feet. I nearly crapped my pants! It looks clean and undamaged but I hope I didn't damage the MAF Sensor when if hit the ground.
The truck sounds like its starving for fuel, so I'm not sure if the fuel pump relay is going or has gone bad, or if its the fuel pump. How to check these items without making it a huge project to diagnose?
Once I can get it to start easily, I have a couple of questions about the trouble code that keeps coming back P0174. That was the original problem with it before the starting problem.The diagnostic says that it is lean in bank 2 but a mechanic friend of mine said something about a vacuum leak.
Ford F-150 - 1997-2003 :: 1999 - Misfire / Running Rough - Code P0305 And P0174
Here is my situation : I have a F150 1999 4x4 ext cab with 326 000 km. A little while ago I got a P0401 code so I decide to clean the TB first and at the same time change plugs and wires since they were overdue. The same code came back and a misfire. Ordered EGR valve, DPFE sensor and selenoid. Realize that I had ordered crappy plugs by mistake. I change all plugs. Had to wait for the EGR valve and others to arrive. I drove the truck for a while since I did not have the time to change the valve and others, during that time the misfire did not come back. Yesterday I change the EGR and others. Today I get a truck that runs really rough and got new codes , P0305 and P0174. I'm really confused now on what should be my next step, should I change the coils, can a P0305 cause a P0174. Should I change vacuum hose going to the EGR , selenoid and DPFE.
View 12 RepliesGolf V R32 :: Throwing P0174 Code After Valve Cover Replacement
A couple months ago I was hearing a hissing noise under the hood throwing the same code replaced the Valve cover, after there was no issues. Yesterday saw I had CEL and I was throwing P0174 code and there is a similar vacuum leak sound coming from under the hood but the Breather in the valve cover is not sucking in air. The Oil cap comes off but the engine starts to bog, what it could be now?
View 2 RepliesFord F-150 - 1997-2003 :: CEL Came On When Coasting Down A Steep Hill - Code P0174
I was coasting down a steep hill yesterday when the CEL came on. I pulled the code this morning and got code P0174, system too lean bank 2.
I cleared the code. Should I just wait to see if it happens again? The truck is running great. There is no sign of a problem. BTW, it's 99 F150 5.4.
Ford F-150 - 1997-2003 :: Code P0171 And P0174 - Vacuum Leak
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
Ford F-150 - 1997-2003 :: 2002 F150 5.4 - CEL Came On For Code P0174 - Misfire On 7 Of 8 Cylinders
So the past few weeks my truck has been sputtering a lot. It seems to do it more so in low RPMS but when I lay on the throttle I didn't really notice it. I haven't had time to look into the issue but yesterday the issue got drastically worse and the CEL finally came on. Registered P0174 as well as a number of other codes including misfires on 7 of the 8 cylinders.
So far I have replaced the fuel filter. Spark plugs are only a few months old. I didnt think it would make sense for all of the coil packs to go out at once so I was thinking either a fuel issue or vacuum leak. Why would it only spit out P0174 (Banks 2) and not show P0171 (Banks 1) along with it? Fuel pump? Vacuum leak? Where should I start? 2002 F150 5.4L...
Ford F-150 - 1997-2003 :: 1998 4.6L - Misfire On Cylinder 6 / Code P0171 And P0174
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 RepliesFord Super Duty (1999-2016) :: Truck Keeps Throwing Communications Code And Goes Into Limp Mode
I recently bought a h&s tuner and installed a dpf delete kit. Everything works great when the truck is not plugged in to the tuner although when I do plug it in, the truck keeps throwing a communications code and goes into a limp mode until I delete the code. I believe it was p0073 but i maye be mistaken. Regardless it has to do with communicating through the obd2 port. I sent the tuner in to get checked out and it turns out its something to do with the truck. I've checked all the fuses and tried to check for broken wires. Where to look next?
View 4 RepliesFord F-150 - 1997-2003 :: Truck Won't Turn Over Intermittently?
Own a 1997 F-150, 4.6 L, 4 x 4. I know it's old but it's in very good body shape, has been undercoated for years. I've only had it for a year. This summer it began to not start (intermittently). The dash lights all come on but the starter will not engage. Brought to my local garage, he changed the starter and the ground cable from the battery.
Was ok for a few months and now it's beginning to do the same thing. Brought it back to him, can't find anything. He did say that the battery is a bit weak, the terminals are spotless (I keep them spotless, coat them with white grease). I measured the voltage with the engine stopped and with it running. Stopped, the voltage is 11.94, running it is 14.87. This clearly shows that the battery is weak.
My question is would this cause the starter to not engage after 4 or 5 turns of the key and then on the 6th try, the starter turns over? I don't want to spend more money ($ 450) the last time and have the same result. If it's possible it's the battery, I'll replace it no problem.
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford F-150 - 1997-2003 :: Truck Has Random Misfire Code
I was involved in a light accident over the weekend. I was hit in the rear by a Prius which didn't do body damage except for the 7 blade harness for my trailer towing. But, now the truck has a random misfire code. You can feel the truck jerk when you go up any grade. We changed the fuel filter and dumped in some cleaner already. One guy says its fuel and one thinks its coils. It is a 2003 F150 extended cab 5.4 with a nearly new motor. The truck has about 175xxx on it and I have had it for about 40xxx. I have not changed coils. We did check the inertia switch on the passenger side and it was not tripped.
View 2 RepliesFord F-150 - 1997-2003 :: Truck Won't Communicate With Code Reader
Truck had a rich on bank 2 code about a month ago, I cleared it and the service engine light stayed off for quite some time.
Last friday on the way home from work the truck started shaking badly right from idle, and at one point on the freeway the service engine started flashing. I couldn't pull over as I was on a bridge but once I dropped my speed the light stayed on but the flashing stopped.
I went to plug the truck in today and first shot it didn't communicate with the code reader at all, I talked to someone who told me that the cigerette lighter fuse is also the OBD port fuse, I pulled a fuse from somewhere else and plugged the reader in again. This time it started communicating with the truck but didn't display any codes while all the while the truck is miss firing and the service engine light is lit up on the dash.
One other weird thing: The fuse had an LED indicator to show that it is blown, when I push the cig lighter in the led gets a hell of a lot brighter, if there is always power drawn through the circuit shouldn't the LED be constantly bright all the time? I'm wondering if there is a short somewhere. Where to look next??
Ford F-150 - 1997-2003 :: Truck Dies At Stop While In Gear - Code P0443
I have a 1997 Ford F-150 with the 4.6L auto trans 189,000 miles
Ok.. there was no problems until the other day when I unplugged the positive side of the battery to replace it's clamp. I Put the new one on and drove to the store but when I came to a stop, the rpm's dropped to 0 and the truck died. I restarted it and every time I would come to a stop it would die unless I give it a little gas also if I start the truck and leave it in park it idles fine until I give it some gas then let off.. the idle drops and dies! If I give it a little steady gas the idle will return to normal.
The check engine light works fine but never once lit up because of this problem! I used a code scanner and if the truck was off and the key forward, it would have no codes. With it running it had the code P0443. I found and replaced a blown fuse and still have the same problem but it reads no codes at anytime. I checked all the vacuum hoses and there seems to be no leaks and the mass airflow sensor looks clean. I have allot of miles but it has been taken care of well and has had a ton of parts replaced over the last few years.
I am wondering why this happened out of the blue and If there is something I am missing that I should be looking at. I don't want to replace the purge control valve if thats not the problem.
Ford F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Ford F-150 - 1997-2003 :: 2002 - SES Light Came On - Showing Codes P0171 / P0174
2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?
View 10 RepliesFord F-150 - 1997-2003 :: Shaking And Idle Bounces Between 500 And 750 - Codes P0172 And P0174
2003 f150 5.4, 4x4 ... Truck is shaking pretty bad, idle bounces between 500 and 750, and its throwing p0172 (rich on bank 1), P0174 (lean on bank 2), and it looks like a misfire on cylinder 8 judging by that power graphy thingy. I'm going to check for a vacuum leak tomorrow on the PCV.
View 2 RepliesFord Super Duty (1999-2016) :: Codes P0172 And P0174 / Truck Bucks And Coughs / Zero Power When Driving
I have a 2008 Canadian F250 SD 5.4 triton. Its got 224000km on it and began to get the dreaded 5.4 dieseling when hot and idling. I replaced the timing chains, guides, both tensioners and crank gear. I confirmed the cam timing was correct with the crank key at 6:00 and the chains marks on the R and L. I replaced 2 coils on cyl's 2 and 3. I replaced the MAF sensor, fuel rail pressure sensor, cleaned and confirmed working the crank sensor and both cam sensors. I fixed the broken Bank 2 cam sensor wires. I changed the plugs and replaced all 4 O2 sensors.
Now the truck idles great but when driving it bucks and coughs and has zero power. I cant even get to 80km/hr. The computer now shows codes P0172 and P0174 which means the Bank 1 is rich and the bank 2 is lean. The O2 sensors are working and moving around. The back 02 sensors are both reading in the 0.8Volt range but bouncing around. The front 02 sensors are both moving from 0.1 to 0.8 constantly. The long term fuel trims are +9.5% bank 2 and -4.7% bank 1 at idle. When the throttle is off idle they become +25% bank 2 and -25% bank 1 . How is this possible and what can I do to fix this engine?.
Ford F-150 - 1997-2003 :: Code P1260 Indicating Attempted Theft Which Disabled The Truck
I have a 1999 F150 with a 5.4L. I recently replaced the PCM with a new unit from autocomputerexchange.net that was programed for my truck. I installed the PCM but the truck did not start. The theft light is also flashing rapidly during cranking. I ran a code scanner a recieved the code P1260 indicating an attempted theft which disabled the truck. I read that if you have two keys you can sync the keys with the new computer but unfortunately one of the keys stopped working a couple years ago (not sure why, stopped for gas and it never started back up). Since i do not have two working keys do i have to tow the truck to a dealer and let them reprogram the keys and reset the PATS or can i have a locksmith recode the keys and sync the keys myself.
View 2 Replies