Ford F-150 - 1997-2003 :: 1999 - Ride Rough - Misfire On Cylinder 3?
I'm working on my 99 f-150. I replaced all my spark plugs and coils after I got a misfire on cylinder 3 reading on the scanner. The truck was running ok but two weeks later it started to ride rough again I checked the scanner and got the same reading for a misfire on cylinder 3. Why its giving me the same misfire again? Could my injector cause that misfire? What about the egr valve?
View 8 RepliesFord F-150 - 1997-2003 :: 1999 - Misfire / Running Rough - Code P0305 And P0174
Here is my situation : I have a F150 1999 4x4 ext cab with 326 000 km. A little while ago I got a P0401 code so I decide to clean the TB first and at the same time change plugs and wires since they were overdue. The same code came back and a misfire. Ordered EGR valve, DPFE sensor and selenoid. Realize that I had ordered crappy plugs by mistake. I change all plugs. Had to wait for the EGR valve and others to arrive. I drove the truck for a while since I did not have the time to change the valve and others, during that time the misfire did not come back. Yesterday I change the EGR and others. Today I get a truck that runs really rough and got new codes , P0305 and P0174. I'm really confused now on what should be my next step, should I change the coils, can a P0305 cause a P0174. Should I change vacuum hose going to the EGR , selenoid and DPFE.
View 12 RepliesFord Ranger / B-Series :: Runs Rough For About A Minute After Engine Started When Cold
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
Ford F-150 - 1997-2003 :: 2002 - Runs Rough When Damp Out?
My truck runs rough/bad when it rains or is damp out. It stutters and had no acceleration. I just had a new fuel pump put in January. It improves after a while on the road. If it's wet, my travel sucks.
View 6 RepliesFord F-150 - 1997-2003 :: Intermittent Misfire When Weather Getting Hotter
Ok I've been getting a intermittent misfire on my truck for soem time now. It ran great all winter but now its getting hotter it intermittently misses. Last summer I replaced all the coils. And the coil inquestion now was replaced since last summer with Motor Craft Coil. I have red the check Engine Codes a d here is the freeze Fram data
DTC :P0351
Fuel System I : Closed Loop
Calculated Load: 71.37%
Engine Coolent temp: 199.4 F
Short Term Fuel Trim Bank 1 : 3.91%
Long Term Fuel Trim Bank 1: 0.78%
Short term Fuel Trim Bank 2: 6.25%
Long Term Fuel Trim Bank 2: 0.78%
Engine RPM :1613.25
Vehicle Speed Sensor: 4.35 MPH
What might be my problem? Since The Short Tem Fuel trim from bank 1 and Bank two are vastly different could that mean my fuel injector is not working correctly?
Ford F-150 - 1997-2003 :: 1998 4.6L - Intermittent Misfire When Accelerate And At Idle
So my truck started to intermittently misfire about a month ago . I changed the spark plugs wires at first and it seemed to get better but it still had a misfire . I replaced the spark plugs and ignition coils and the misfire is still there . Up until the other day it was a noticeable issue but still drivable with . On my way home from work it got alot worse and started to misfire any time I tried to accelerate and now is noticeable at idle now as well.
I checked the fuel injectors resistance and they are about 14.8 ohms . I am not getting any codes for a misfire . I tried to pull the fuel injector connectors to try to find the source of the misfire but could noticeable change in engine rpm. Where to go from here and what I should check first? Would a clogged fuel filter cause something like this ?
Ford F-150 - 1997-2003 :: 2000 - Start But Runs Rough While Stepping On Gas It Dies - Missing Gas Cap?
I have a 2000 E350 boxtruck with a 5.4 auto. The motor is a new rebuilt with about 4000 mile, coils were replaced with motor, injectors were rebuilt with motor.Today (500 miles from home) the truck died. I was going up a slight hill on an interstate. It will still start, but runs very rough and when I put it in gear and step on the gas it dies.
So I had it towed to a garage. While pushing it into the garage I noticed my gas cap was missing. I know it was on 45 min earlier because I got gas. Did I forget to put in back on? probably.. But I wondering if the missing gas cap could cause the truck to run bad,vary bad?
Ford F-150 - 1997-2003 :: Idle Very Rough Like A Misfire
I got a 97 f150 4.2l from my neighbor. he takes good care of his vehicles. he sold it to me cuz it started to idle very rough like a misfire. it is hard to start when cold spits sputters and pops. once started idles like it wants to stall, then will idle normally then back to rough. back and forth like that. runs like a champ when going down the road . check engine light was on took it to auto store they checked codes . said bad o2 sensors so i changed them. still same issue. neighbor changed coil packs checked spark plugs and wire. every thing fires good. i changed iac. still didn't fix problem. could this be a bad egr valve or sensor? if so how can i diagnose this? he also thought was a clogged cat and bored it out. tight budget can't afford to take it to a mechanic. Was told spray carb cleaner spray around engine to check for leaks that did nothing at all...
View 14 RepliesFord F-150 - 1997-2003 :: 1998 4.2L V6 - Changed Plug Wires Now Runs Rough At 2000 - 2500 RPMs
My F150 with 175,000 miles on gave me a the ol' P0305 code indicating misfiring in cylinder #5. I changed the plugs and wires using Motorcraft wires and Motorcraft AGS34FM plugs.
Now the truck idles fine, does not give a OBD code but runs rough at 2,000-2,500 rpm. Tried it out on the highway and it started "bucking" a bit. Not sure what to try next.
Ford F-150 - 1997-2003 :: Rough Idle At Start For About 30 Seconds - Cylinder 1 Misfire
2000 5.4l lariat. My cylinder 1 for 2 years has been poping p0301code and has a rough idle at start for about 30 seconds. It also has a little white smoke for that 30seconds. new cop, new spark plug, new spark plug pig tail, swapped injectors to different cylinders multiple times to change code no luck. Compression dry and wet are at 200 and all cylinders are within10%. I had a dorman intake manifold installed 4 years ago and the code came a few years after. Im thinking intake manifold gasket is bad between cylinder 1 and the heater bypass tube allowing coolant to slowly leak down into the cylinder causing my rough start. I looked through the injector hole but could not tell. With all the info I have given is there any other places or things that it could be before I do a gasket replacement or is all my tests leading to the intake manifold gasket...
View 5 RepliesFord Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord F-150 - 1997-2003 :: Misfire / Rough Idle With Sulfur Smell - White Exhaust?
My 2003 F150, 5.4L has been having some rough idle/misfires issues both at idle and under load.
I have fixed one big vacuum leak, replaced the PCV valve, new sparkplugs, seafoam and heet in the gas, replaced fuel filter, tested the fuel injector resistance. Coolant levels have not changed. The truck burns about a quart of oil every 1000 miles or so. The white exhaust is heavier than condensation, but it comes and goes. The rough idling comes and goes as well, and it usually happens under load and the CEL flashes.
The codes I get are random cylinders, po303, po308, po171, po174 were the most recent but there have been other cylinders as well. I clear the codes after each attempt to fix it and they come back different.
I notice that there is a small exhaust leak that drips water just behind the engine, and when I shut down the truck a lot of water will pour out of an area just behind the cab on the passenger side as well as out of the bottom of the muffler (small hole, looks drilled).
Usually the rough idle occurs after filling up the tank, but from different stations so I do not think it would be watery gas. I use Heet every fill up as well. Also, there is a sulfur smell after the rough idling occurs (catalytic converter?).
Ford F-150 - 1997-2003 :: Skipping / Rough Idle And Loss Of Power - Misfire On Cylinder 4
Replaced the spark plugs and wires a couple months ago. Started skipping yesterday throwing the #4 misfire code so I replaced the coil pack, reset the check engine light but it's since came back on and has a rough idle and loss of power. By the way, it's a 97 F150 4.6L 4x4 with 200,000 miles.
View 4 RepliesFord F-150 - 1997-2003 :: Runs Rough And Stalls When Stop Or Rolling To A Stop It Would Die
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Runs Rough When Cold
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Truck Runs Rough When Cold
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Runs Rough And Stalls After Half Mile?
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
Ford 7.3L Power Stroke (1999-2003) :: Runs Rough Then Stalls - Check Engine Light Came On
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Idles Fine But Runs Rough After Warms Up A Little
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.