Ford Exhaust System :: Exhaust Leak - No Gasket Or Donut Ring In The Flange?
I tore it apart and there was no gasket or donut ring in the flange. Is there supposed to be a gasket or donut ring? I can feel the leak with my hand. I have retightened & it still "tick-ticks" real bad.
View 7 RepliesFord Exhaust System :: Exhaust Leak At Manifold Where Donut Gasket Meets The Catalytic Converters
My truck just started running really loud when it's cold and the leak goes away when it warms up to operating temperature.I did a little bit of investigating and I have found where the leak is coming from at the end of the exhaust manifold where the donut gasket meets the catalytic converters. It appears that the bolts rotted that hold the system together at the gasket. What should I do to repair this? I don't really want to replace the whole manifold because I know I'll break a stud off in the engine because everything is pretty rusty down there. I even took some pictures of the problem....
View 3 RepliesFord Exhaust System :: 1987 Ranger - Engine Is Running Very Rough And Seems To Miss At Low RPMs
How many O2 sensors does a 2.3 fi 4 cyl. have. I think just one on the manifold, but I'm not completely sure. Engine is running very rough and seems to miss at low RPMs, has no power and drinks gas like crazy!!! Emissions light is on on the dash. I'm thinking O2 sensor......tried replacing, but couldn't get enough torque on the sensor socket wrench to loosen, may be rusted.
View 6 RepliesFord F-150 - 1997-2003 :: Exhaust Leak On Passenger Side / Broken Exhaust Manifold Bolts
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesLexus GX 2004-09 :: 2005 Engine Running Rough / Exhaust Leak At The Head
My GX had developed yet another issue. To start off my car has an exhaust leak presumably at the head. Thats what i been told. This condition would throw a P0430 code ( catalyst system efficiency below ) once or twice a week, which id just erase with my plug in tool. Im not sure if the new developed issue is related to it, but now the engine is running rough especially noticeable between 1000-2300 rpm. Feels like misfire. When driving i can feel a drone or a frequent shake if rpms are in that range or when unloading the motor and rpms are dropping. No codes! Timing belt was changed at 90k miles car has 150k now. Not sure if its due for another one now and this can be the cause.
View 8 RepliesFord F-150 - 1997-2003 :: Exhaust Leak Cause A P0171 Code / Idling Rough And Almost Stalling At Red Lights
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
Ford Excursion :: 2003 - Rough Idle - Puff Of White Smoke On Cold Startup - Slight Exhaust Leak
I've been chasing a problem all summer. Began with crappy batteries dying intermittently. I replaced the batteries, FICM, finally cleaned EGR valve and replaced ICP with pigtail. The problem is still persistent. Basically a rough idle, puff of whit smoke on cold startup, rough running at around 1500 rpms( driving at 50 mph). The ICP was soaked in oil so i was confident replacing it would finally cure my issues. It actually got worse with the rough idle turning to a surging idle and quite rumbly at 50 mph speed. I guess its time to look to injector issues but i thought id check if after replacing icp/ cleaning egr. I also have a slight exhaust leak at turbo out that i can see. The clamp is not seated properly. This after turbo connection to exhaust.
View 1 RepliesFord Exhaust System :: 351w Exhaust Collector Stud Nut Size
I have a 90 bronco with a efi 351w and im missing one nut for the manifold to exhaust pipe flange. I have looked all over the net and can't find the size I know its a 1/2in socket but I need the thread pitch and size, had the parts guy try to sell me the stud and nut kit seem really expensive for just a nut and to install the full kit I have to pull skid plates and the trany supports just to start to get room to do the job, seems like a lot of work to replace 1 nut...
View 1 RepliesFord Exhaust System :: Exhaust Quieter When Cold / Much Louder When Warmed Up
My F150 exhaust seems rather quiet when I first start it up, but after it gets warmed up good, the exhaust is much louder (which I like). I started wondering if I had a crack up front that widened out when it got hot, so looked under it when I got home today with it hot and still idling, but didn't see any cracks. Also I did not hear any noise like a leak. All sound was coming from the side exit pipe. So... what is the phenomenon that would cause this?
View 5 RepliesFord Exhaust :: 2000 - Can Remove Catalytic Converter From The Exhaust System?
Long story, I'll try to make this short, 2000 E250 5.4L What would or could happen if the catalytic converter was removed from the exhaust system?
View 5 RepliesFord Exhaust System :: 2006 - Exhaust System Installation?
Want to install exhaust system on my 06 F350.Tell me,what is the best brand for my truck,I know, very good intake system is from K&N,what about exhaust?
View 10 RepliesFord Exhaust System :: 1996 F150 - Exhaust Making Strange Howling Noise
Ok, probably about 1/3 times i start my 96 f150 4.9 with true duals, the left pipe has a higher pitched howling noise, its a steady tone whether I rev the truck up or not it just gets louder. It will do it for about 6 seconds and then stop. The truck doesn't run badly because of it, but i took her to autozone to get her scanned and they said that the oxygen sensor on the first manifold bank has a slow response on startup. Is that what causes this strange noise, I don't even know how it would make it, it sounds much different from the engine. The right pipe doesn't do anything.
View 9 RepliesFord Exhaust System :: Exhaust Manifold Leaking / Louder Than Normal Knock When Accelerating
Leaking exhaust manifold? The truck has a much louder than normal "knock" when accelerating. At first I thought and had some bad fuel in the tank. I eliminated that with a full take of good fuel and some STP but the "knocking" continued. Then I thought that perhaps it wasn't firing on all cylinders but it felt like it had full power. I took it to my mechanic and he said it as a exhaust manifold leak. He said that he has never replaced the exhaust manifold but that it was a "nightmare" and expensive. He also said that it's not a safety issue but on the long run the leak would cause the truck not to pass its emission test. He said the problem was with rusted bolts that would be difficult to remove.
View 12 RepliesFord Exhaust System :: 1994 Ranger - Loud Exhaust Sound In / Outside The Truck And At Idle
I have a 94 ranger 4L. I am looking for a more loud exhaust sound in/outside the truck and at idle. I have had a cherry bomb turbo on it and it was ok but not loud enough for my liking. I just picked up a flowmaster 40 2 days ago and it sounds good but again just not loud enough for my taste and kinda a lot more. I was looking for a louder muffler that is not a glasspack and would like to stay under like 80 or so.
I also thought about getting a high flow cat which i think might make some more sound but was not sure. Im running the stock pipe which is 2" and end in back of the wheel on the right. I look at the Hooker Headers Maximum Flow Muffler which i thought would be louder b/c it's more straight through the muffler so it would put off more sound better. What would u recommend for something more loud ?
Ford Exhaust :: Exhaust Manifold Leak Due To Broken Rusted Bolts
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 RepliesFord Exhaust System :: 1994 F250 - Replacing Exhaust?
I have been thinking about toying with my exhaust. I don't have a crazy amount of money. I got a 94 F250 with the 5.8 liter 351. Heres what I was thinking. Get rid of everything after the cat, and then run a single 3 inch pipe from the cat to a flowmaster 40 series, and then exit either right before the back tire or right after it.
View 7 RepliesFord Exhaust System :: Exhaust Pipe Cut Just Behind The Rear Of Cab - No Muffler
i have my 4 inch exhaust pipe cut just behind the rear of the cab right now with no muffler. If i cut it further up maybe jsut under the front seat or so what would this to the sound? would it make it deeper or louder?
View 7 RepliesFord Exhaust System :: Copper Exhaust Coming Off The Headers
Why it won't work. copper exhaust coming off the headers. I have the ability to get it and bend it and how cool would that be copper duals. Why won't it work. If I bolt it right to the headers.
View 7 RepliesFord Exhaust :: Crack And Subsequent Leak In Exhaust Pipe
Actually developed a crack and subsequent leak in a pipe running lengthwise, so assume the factory weld over the years went bad. Since it would be a weld overhead, wonder what method would be best? Would oxy acetylene work or mig? I don't have a tig so that not an option for me.
View 2 Replies