Ford Ranger / B-Series :: Check Engine Light Popped Up Showing P1000 And PO401 Codes
1999 ranger 3.0. Check engine light popped up showing P1000 and P0401 codes. I think the p1000 is a system readiness test. Not sure why that came up and the 401 is exhaust gas problem. I put on a new autozone DPFE a few months ago..
View 5 RepliesFord F-150 (2004-2008) :: 2005 - Codes P0325 And P1000 - No Power When Throttle Is Pushed Hard
I have a 2005 F150 5.4 FX4 and I had these two codes thrown over the past week/few days...P0325 and P1000 (pictures below of descriptions...I have an edge programmer and have been running it on the highest setting for a while now but always run premium fuel. I got these codes and reset them and they came right back. I then reset the cpu to the factory programming and they still keep coming back. I still have premium in it and it seems like when you hammer it that it falls flat on its face! It runs good and pretty smooth but seems like it has no power when throttle is pushed hard. It seems like it has a small vibration at about 3,000 RPM but only for a few seconds and then smooths right back out again. The truck has 88,000 miles and I just put new Motorcraft plugs in it about 6,000 miles ago. Not sure what I should do or what is the next step.
Photo hosting sites ...
Image ru ...
Ford 7.3L Power Stroke (1999-2003) :: E99 Stalling And Sometimes Running Rough - Codes P1280 And P1247
E99 Romps on start up and randomly dying. Bought this truck about 3 weeks ago. Previous owner mentioned he had issues with it getting hot and shutting off and not starting. Has new IPR, ICP and pigtail, I just put in a new fuel filter. Has 206k miles on it and is the 4R100.
The past two days after sitting all night I have been cycling the key twice and it hasn't done its romp. Typically when it does I can tap the pedal once and it goes away. This I could deal with but its started to die randomly while driving, never while cruising down the road. Its either just after starting it and rolling slowly or slowing down for a stop or to turn. When it dies, I can put it in neutral and it fires back up no problem. SES light usually comes on for about 10-15 seconds after but goes away.
Replaced the grey CPS that was in it with a dark grey one from RiffRaff Diesel. Got a Edge CTS2 to figure out the problem, the codes Im getting are P1280 and P1247.
The ICP pigtail they replaced they spliced on with butt connectors. I plan on pulling it to check for oil and make sure it does look new and redo the connections with solder then shrink wrap them.
I was told to check the IPR% under full throttle which I did and it never went higher than 36.7
The truck did start running rough around 45-50 mph and I did get a video of the ICP jumping around while cruising down the road.
Then I went through a drive through and the truck kind of hiccuped like it wanted to stall and the ICP went right to 725 PSI and idled up and stayed there until I started to leave.
Truck is pretty much stock, K&N air intake and muffler cut out and straight piped.
Here is a link to the videos I got :
e99 7.3 ICP fluctuation while driving - YouTube
e99 ICP steady at 725 PSI after acting like it wanted to stall. - YouTube
Ford Excursion :: Started Spattering And P1280 Code Popped Up?
I did a CCV MOD and washed the engine with simple green and a garden hose yesterday, started the truck and it was running fine for about 10 min. After that it started spattering and a P1280 code poped up. Is it related to a wash or ccv? It does not stoll but idles bad, drives fine once i get it over about 5mph.
View 1 RepliesAccent RB (2012+) :: Engine Light On - Codes P1445 And P1000
Driving car today and the engine light came on, so before going home I stopped at local garage and had it checked. this is what they got- first code P1445, second code P1000. Car is a 2012 Hyundai Accent automatic hatchback with approx. 40,000 km. (25,000 miles) bought in May of 2012.
View 5 RepliesFord Excursion :: 2007 - Truck Taking Three Cranks To Start / Code Is P1280
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Idle Roughly - No Power - Got Codes P1280 And P1316?
Started my truck yesterday and drove about 1/4 of mile and all of a sudden I lost all power but was lucky enough to creep back home. Had a friend put it on a scanner and it spit out P1280 and P1316 codes. My truck will start and idle rough but has no throttle response and no power. I changed out the CPS and ICP and the problem still exists. I got an infrared thermometer and checked the heat coming off each manifold and the driver side was reading about 200 while the passenger side was reading about 75 while at idle. Pulled valve pan cover off the passenger side to check and see if the harness came loose and everything looked fine. So my question is do you think this could lead to a bad IDM?
View 9 RepliesFord 6.0L Power Stroke Diesel :: SCT EGR Delete And CEL Light - Code P1000
I'm brand new 6.0 owner. I am going to be performing many of the bullet proofing steps including plugging off of or a complete delete of the EGR cooler. I've read that the SCT tuner will turn off the CEL light and stop the ECM from operating EGR function.
What I can't find for sure is will I get a code P1000 (drive cycle not completed) with EGR turned off. Here in Seattle if you have a code P1000 stored you will not be allowed to complete emissions testing to get your tabs renewed. I'm guessing it does not set P1000.
Ford F-150 - 1997-2003 :: Got Error Code P1000 - Idle Rough - CEL On?
What that means? The check engine light is NOT on but I looked for a code because my truck is idling rough, and when driving, when the overdrive kicks in, it vibrates really bad. As if a bad U-joint on your drive shaft. The truck has been in a field for about 5 months broke down so any clue? Haynes manual says nothing about P1000.
View 13 RepliesFord F-150 - 1997-2003 :: 4R70W Shifting - Can't Go Faster Than 40 Mph - Got Code P1000?
here is the full story. just gotten truck out of the shop for a lower end rebuild and diff rebuild, truck set for about 5 to 6 months with no battery or motor. Engine runs great! besides a P1000 code.
I can drive down the road and can't go no faster then about 40mph without going to or over 3grand on the tac. I took it to auto parts store and gotten codes for both shift sol. and found out that the internal wiring harness was bad, and replaced it today. and cleared the codes. left parts store truck went shifted to 2nd and started to seem like it was going to go into 3rd then the rpm's went up like I was getting on the pedal when I wasn't and now it is going the same thing again. but took it back to parts store and checked for any codes and just got P1000 code and code about my speed sensors but they have been bad for a while.
Ford 7.3L Power Stroke (1999-2003) :: Intermittent Starting / Code P1280
My 02 f250 w/ 7.3 won't start. Cranks and nothing. No smoke or anything. For the last year It has had a intermittent starting problem, where I would drive it for 15-20 mins. If I shut it off like I would if I was at the fuel pump and then restart it, it wouldn't. I'd have to wait 30 minutes with a hood open and then it may start. Other times I would have to wait hours.
I tried replacing the crank position sensor, the fuel pump and filter.I did all this in the Last 300 mile . There's No change. After a week or two of sitting it won't start. What can I check and what can I try.
To add more info. Since I am not the original owner I pulled the computer that is located behind the ebrake to see if someone else had installed a chip, as I've heard that if that chip goes bad then the truck won't start. I disconnected that battery and pulled it. Negative on any chip. Put it all back together and tried again. No start. I borrowed a code reader tonight and pulled a P1280 code. I'm back to square one.
Ford F-150 (2004-2008) :: Code P1000 - Evap Monitor Doesn't Complete
I am working on a 2005 F-150 with a 5.4L 3V engine.
I had the battery disconnected doing some other work and now the Evap monitor will not complete and keep getting a P1000.
I have followed the drive cycle instructions and all the monitors have completed except the Evap monitor. Ford Motor Company Driving Cycle
What would cause it to fail?
Ford 7.3L Power Stroke (1999-2003) :: 2000 Truck Taking Three Cranks To Start - Code Is P1280
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Leak At Passenger Side Up-pipe To Manifold - P1211 And P1280
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
Ford F-150 (2004-2008) :: Intermittent Starting - No Sputters / No Hiccups
Intermittent starting issue in these things? Seems to be getting more common for me this winter. Turn the key, it turns over, and then I let go of the key and she doesn't light. Then when I try again, it's like the engine is flooded. I have to give it gas to start, which I know is a no-no in fuel injected vehicles. Other than that, it's fine. No sputters, no hiccups, runs strong, good mpg, etc. But I'm getting annoyed....
View 14 RepliesFord Excursion :: 2000 6.8L - O/D Light Flash Sometimes But No Codes
My O/D Light flash some times, no codes thrown. What could cause it?
View 9 RepliesFord Excursion :: Codes For Cylinder 8 And Then 7 - 2 Bad Coils In 3 Days
So on Thursday night I replaced all of the plugs and boots on my 01 v10. I used Autolite 103's and Autolite boots. On Saturday the truck threw a code for cylinder 8. I bought a bag of 8 used coils off a buddy who has a mustang buy a few months ago so I put one on, cleared the code and the miss went away. On the way home tonight the truck started missing hard, but no CEL. I use torque, so i did a scan anyway and it pulled a code for cylinder 7. I haven't been out to troubleshoot yet. Could I have done something wrong for 2 coils to go in such a short amount of time? I followed the write up in the tech folder. Used proper torque specs, dielectric grease, and anti-seize on everything.
View 6 RepliesFord Excursion :: Sputtering And Chugging - Throwing Many Codes?
I have had a wet weather issue twice, once last fall and once this spring. Both times were very wet and damp conditions causing a sputtering and chugging and dying at lights, both times no codes and after drying out in brother's shop it went away. Now this weekend up at the cabin it reappeared, again very wet conditions. Replaced the MAF...no change. Sputtered and chugged my way home with it killing at most stop signs/lights. Finally got home and couldn't even back the TT up the driveway, it would kill. Finally threw numerous codes (misfire in cylinders 1 and 9, and misfire in first 1000 revolutions). I'm thinking COPs as the plugs are not that old and the little research I have had time to do suggests this also. If it is COPs, I have heard there are some to avoid and some that are recommended?
View 9 RepliesFord - Windstar - Engines - Cylinder - Sparkplugs :: 2001 - Hiccups While Idling Or During Drive
I had a spark plug break on me and it caused a misfire. I took it in and the mechanic replaced all spark plugs and wires. After getting the car back, I experience an occasional engine hiccup here and there. Took it back to the mechanic and told me that he cleaned off the valves of carbon build up. This did not alleviate the current symptoms. It is more noticeable while I am idling. It feels like a jolt. It appears to be worse after a cold start. I do not have a check engine light or do I notice the RPM needle go wild. What is the mechanic missing? What could still be wrong with the engine? Vehicle is a 2001 Ford Windstar Sports SE, 6cyl, 3.8L ....
View 5 Replies