Ford F-150 (2004-2008) :: 2005 2WD - Misfire And Hard Jerk When Going Uphill - Codes P0300 And P0171
I have a 2005 F-150 5.4L 2WD 90K miles. I started getting a misfire and hard jerk when going uphill. No codes for a few days but misfire got a little worse and more jerking at full throttle acceleration or level throttle up a hill got codes p0300 and p0171. I replaced the fuel filter cleaned MAF and changed plugs Motorcraft plugs (none of them broke during replacement). Miss got worse. Missing at idle and no power 3K rmp to get to 40. Only code pulled was p0171. Replaced upstream O2 sensors and COPs. Will barely idle now. Dies when put in gear. Full throttle barely moves forward a few feet just sputters. Checked vacuum lines cannot find anything. Only code I get is P0171. Fuel injectors next? Or shop?
View 3 RepliesFord F-150 (2004-2008) :: 2005 - Power Loss And No Throttle Response
2005 F150, 5.4 motor. Truck would loose power and no throttle response. Shutting off and restarting, ran fine. No codes showing. Cleaned throttle body and plate, reassembled. Key left on for 20 minutes. Tried to start vehicle. Making a clicking sound, dash lights flashing on and off when hear clicking sound when trying to start vehicle. when key turned to on position, dash lights go off except check engine light. When checked, no codes shown.
View 3 RepliesFord F-150 (2004-2008) :: 2005 - Whining Noise - Loss Of Power And Hard Shifting In The Transmission
I posted awhile back about a loss of power and hard shifting in the transmission. I thought I had it fixed, well I kind of did...... Replaced the IWE that had locked in solid. I replaced both, added some transmission fluid, new front brakes, and a new belt back in July/August. Truck was fine for a few thousand......
Well it's back. Now I have a noticeable whine in the cab. I haven't pin pointed it yet. It is only audible when the truck is running from 35-50 mph. It is not RPM dependent, it doesn't change when I take it in or out of four wheel drive. It isn't there when the truck isn't moving.
The truck has 61,000 on it. I bought it with 35,000 on it because I wanted a vehicle that wouldn't nickel and dime me. Something I could climb in and not worry about making home.
Well here I am less than 30,000 miles later and I have had issues with the fuel controller under the bed, brake calipers sticking, IWE's, new shocks, broken front coil spring, recall for the airbag, tie rods, ball joints, power window regulator, and now what appears to be a transmission.
I come from a long line of "FORD" guys, but I am seriously considering something else. This 04-08 model has to be one of the worst pickups ever built by ford.
Are the newer ones any better? Other than routine maintenance a vehicle shouldn't have to be touched before 61,000.
Ford F-150 (2004-2008) :: Code P1000 - Evap Monitor Doesn't Complete
I am working on a 2005 F-150 with a 5.4L 3V engine.
I had the battery disconnected doing some other work and now the Evap monitor will not complete and keep getting a P1000.
I have followed the drive cycle instructions and all the monitors have completed except the Evap monitor. Ford Motor Company Driving Cycle
What would cause it to fail?
Ford Excursion :: New ICP / CPS But Still Hiccups - Codes P1000 And P1280
I have not yet managed to fix the Ex, i have replaced the CPS with a Delphi 101 cps, and the ICP sensor. The truck ran great for almost 3 hours, but then started acting up again. Codes I pull are P1000 and P1280.
The p1280 code is probably from a loose connector, i got injection pressure of 728psi constant at idle and during low rpms, will fix that tomorrow, but that is probably not what causes the hiccup, but if my new one is function correctly, then i might be something else? The old was from stock and had an oily connector, i have replaced the pigtail though.
The funny thing is, that when i open the hood, the rpms will climb up around 200rpms at idle, to right under 1000rpms, it will do this slowly, takes about 10 seconds. Close the hood and it goes back to normal, so maybe a vacuum leak? When i slam the hood shut, it will sometimes do the hiccup. I have managed to loose 2 of the bolts to the valve cover, but it sits tightly.
Really lost on this truck, what can cause this hiccup, when it does it, the water-fuel light comes on (got a new filter in it). I also have a check engine light, but if i delete the codes when its running, it goes away until startup again.
Another thing i have noticed is that the truck is slower to start then normal, before i got this problem, the truck would start right up when turning the key, now i have to crank it for about a second more.
Ford F-150 (2004-2008) :: 2005 - Electronic Throttle Control / Wrench Light
2005 Ford F-150 FX4 5.4 V8
So my battery died the other day when I was working on the radio and I ended up having to jump start the vehicle. After the jump start the Wrench light came on the truck or the ETC light. (After doing research I have discovered you are not supposed to jump start a vehicle with ETC)
I have taken the car to the auto parts store and it does not seem the code readers they have can read codes for the ETC light.
I have also disconnected the battery cable to try and reset the light, but it still always comes on about 10 seconds after starting the car.
I have had no issues with the vehicle despite the light. No rough idle, no starting issues, or acceleration issues at any speed. What I can do to resolve this light or what part I fried when I jump started the car?
Ford F-150 (2004-2008) :: 2005 - Got Codes P0022 And P0345?
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
Ford F-150 (2004-2008) :: 2005 Truck At Partial Throttle Will Shake When Going Up Slight Incline
.Here is a run down of my truck 05 5.4L Screw has 130K on it. Sometime when going up a slight incline the truck at partial throttle will shake very very little. if I put my foot into it the shake goes away and the truck response just fine. It only does this when going uphill on the freeway and on the streets here in Dallas that have slight inclines.
The truck is not throwing any codes nor does it stall at lights. Starts right up in the morning and runs good. Nothing done to the truck except I have an Edge programmer and Magnaflow exhaust. I have pulled the programmer off and returned the truck to stock and it still does the same thing.
I bought the truck used in 07 had 40K miles on it. I'm thinking spark plugs or maybe a coil is going bad. But this doesn't happen all the time just here and there.
Ford F-150 (2004-2008) :: 2005 FX4 - Whining Or Whirring Noise In Rear When Pushing Throttle?
I just bought a 2005 fx4 and there is a whining or whirring sound coming from the rear of the truck when I hit around 70km/h. the second i let go of the accelerator it stops.
Today when I got home after a 15 minute highway drive, i got under the truck and felt the differential area. it was warm but not hot. and there was a wet spot on it. i wiped off a drop of oil. there was also a wet spot on the bottom, seemed to be just water? I'm not sure.
Nissan - Altima :: P0100 And P0325 Codes Appear Even After Changing MAF
I replaced the MAF a week ago but the code P0100 is still there. Car runs fine in the highway but I do notice acceleration issues. I got the knock sensor but I cannot find it in my nissan altima (2000). The car shakes while stalling, at a red light, and pretty much as soon as I stop. Putting the car in N will work a bit but won't stop the shaking. Should I focus on the MAF again or should I keep trying to replace the KS? Where it is?
View 3 RepliesFord F-150 (2004-2008) :: 2005 - Idle Really Rough / Revs Will Rise And Then Drop Again If Blip The Throttle
I just locked out the cam phasers on a 2005 f150 with a 5.4. It now idles pretty rough. If I blip the throttle the revs will rise and then drop again, and it barely catches in time to prevent a stall. If I continue to tease it this way I can usually get it to stall. I'm getting no CELs or anything, but I intermittently will get a P035x code (it seemed to rove. I've gotten cylinder 1, 4, 6, but not consistently.). I have chased those around by swapping coils, checking/cleaning the connectors, etc.
I am kind of thinking that these codes are a symptom of my idle issues, and not the actual problem. What could I have done wrong? Could it be a vac issue? I had basically the entire ECU harness and all the vac lines disconnected to do the job, but as far as I can tell everything has been reconnected to the correct locations. I did have an SCT tune done to remove the phasers in the ECU. I installed it and still have the issue, so for now I am on the stock tune just to eliminate any variables.
Could my tune be the issue? Is this how you would expect the engine to behave with locked out phasers and no corresponding ECU tune?
Ford Ranger / B-Series :: Check Engine Light Popped Up Showing P1000 And PO401 Codes
1999 ranger 3.0. Check engine light popped up showing P1000 and P0401 codes. I think the p1000 is a system readiness test. Not sure why that came up and the 401 is exhaust gas problem. I put on a new autozone DPFE a few months ago..
View 5 RepliesFord F-150 (2004-2008) :: 2005 - Injector Stuck Open - Shake Really Bad - Got Codes?
Well I believe I finally had the opportunity to experience the wide open injector issue. I was driving to work and all of a sudden at a stop light my truck started shaking bad. It went away but as I took off every so often it would shake. I thought it was a tire or front end component so I pulled over and just got overwhelmed with the smell of gas. I drove 30 miles back home and check engine light blinked the whole way and truck ran . Also wasted at least a 1/4 tank of gas and the a/c wouldn't blow cold air either. Hooked it up to read DTC codes and got P0172, P0300, P0303, P0304, P0316 and P2196.
View 14 RepliesFord F-150 (2004-2008) :: 2005 STX Hard To Start When Cold
I have a 2005 STX with 107,000 miles on it. When it is cold you have to turn the key on for 5 seconds twice then start it. When it is warm it will start like it always did. When the temperature outside is 60 or above you have to do the key thing about 5 times. I think it is my fuel pump...
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 - No Codes / Hard Start And Smoke
I just bought an early 04 (01/04) and it starts hard when it's cold. It starts just fine when it's warm. It idles a little rough it seems and it's putting out white smoke, but not too thick. There are no codes on the truck.
I performed the "bubble test" and got no bubbles at all. I have found that it is common for oil rail o rings and dummy plugs go bad and I'm being told that is what the problem is.
Could the oil rail seals be the problem? It makes sense to me only because there are no codes and I feel anything else would have thrown a code.
Accent RB (2012+) :: Engine Light On - Codes P1445 And P1000
Driving car today and the engine light came on, so before going home I stopped at local garage and had it checked. this is what they got- first code P1445, second code P1000. Car is a 2012 Hyundai Accent automatic hatchback with approx. 40,000 km. (25,000 miles) bought in May of 2012.
View 5 RepliesFord F-150 (2004-2008) :: 2005 - Check Engine Light Came On And Pulled Codes P2160 And P0506
I have an 05 F-150 Lariat 5.4 and it has been going haywire today. While driving if I hit a hard bump the power will cut off (radio, a/c) and even sometimes the truck. Check engine light came on and I pulled codes P2160 & P0506. Also, when it completely cuts off and I start it back up it says "engine in failsafe mode".
View 1 RepliesFord F-150 (2004-2008) :: 2005 - Hard Starting In Cold Weather
How to diagnose what I think is a failing alternator?
Here are the symptoms:
- Hard starting in cold weather
- Battery not at full voltage when truck is parked (usually around 11.5-12 volts. I have been putting a charger on it some nights)
- Lights seem to dim when I've got accessories running, like heater fan, heated seats etc. Lights get brighter with engine RPM, like when pulling away from an intersection.
What's my next step to diagnose this? I did a search, and didn't see anything. My battery is probably still under warranty, so if that's the issue, it should be a free fix. How hard is it to install an alternator in a 2005 with 5.4L engine?
Ford F-150 (2004-2008) :: 2005 - Smoking White - Got Codes P0174 / P0300 / P0305 / P0306 / P0316?
05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.
P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution