Ford Super Duty (1999-2016) :: 2000 - Getting Code PO303 Due To Deposit?
I was getting codes on 3,6,8 cylinders. I found a broken wire at the coil on 3 and the bolt was broken that secures the coil. No plugs were blown out. I replaced coils and plugs on those cylinders and rewired at #3. I also checked and cleaned the injectors. The 6 and 8 codes are gone but still getting a code on #3.The coils were out of wrecking yard and I suppose it could be a faulty wiring job. Could I take a well-insulated screwdriver and check for spark from the coil at the spring? The plug was heavily deposited as it had not been firing. Could deposits be causing other issues with raw fuel having been dumped in the cylinder?
View 10 RepliesSonata NF (2006-10) :: Low Oil Pressure Light On Idle Under 1000 RPMs - CEL Code P0021
Well, it's looking sort of depressing for my '06 Sonata! I had an oil change done yesterday and now I'm getting a Low Oil Pressure Light on idle under 1,000 rpm's. Today the check engine light came on and it's code P0021.
I also experience very noisy "bearing" type noise upon start-up which happens for about 10 seconds or so. This has been going on for a month or so.
During my online research it's appearing that I may be suffering from the dreaded Timing Chain Tensioner I've read a lot about.
I'm aware of the TSB (10-EM-006) and have a copy of it if needed.
My question is this...my Sonata has 151,000 miles on it, well beyond the 100k warranty period. Will Hyundai repair my issue as a warranty item under that TSB?
Subaru - Outback :: Found Engine Oil Jelled Up - Code 0028 With Less Than 1000 Miles After Oil Change
2011 Subaru outback with 49000 miles. Regular oil changes every 5000 miles with Subaru filters. After the last oil change at 45000 miles the engine started shuddering when reversing from garage at @48300 miles. Once warmed up drives okay. Within a week it threw up code 0028 and found engine oil jelled up. Drained, flushed and replaced oil. I replaced the oil pressure switch and solenoid just in case. Code came back with less than 1000 miles after oil change. Can't understand the reason for jelling. Have been using Castrol GTX 5-30 all the time with Subaru OEM filters.
View 5 RepliesFord Excursion :: SES And ABS Lights On - Code PO500
So I am starting down my long list of repairs needed on my new to me ex. I have a SES light on and a ABS light. Went into Advance to have them check the code. Came up with PO500. Did a search here and found out that it is the vehicle speed sensor. Probably explains my intermittent loss of speedometer. Did another search to find out where this sensor is and can't find anything. Where it might be? It is a 2000 Limited v10 4x4....
View 9 RepliesFord Excursion :: 2001 - Got SRS / Airbag Code?
I have suddenly acquired a new value added feature to my X. An airbag warning light flashing code 18. Through the research I have found it is either a pretensioner issue or a short. Would like to know for sure what it is.
It is a 2001 LTD 5.4L.
Ford Excursion :: 2001 V10 - Getting Code P0720?
I have searched and found a few threads of folks getting a p0720 code and truck revving and dying. Just wondering how to resolve the issue and what the cause was. I have an 01 ex with v-10
View 13 RepliesFord Excursion :: 2003 - Contribution Code With 8 New Injectors
I have an 03 X with 225k on it. I put 8 new injectors in it because I was leaking fuel into the engine oil. I got them from dieselogic from ebay in Jacksonville FL. 4 of those were leaking and they warrantied them. Then 2 of them were getting contribution codes and they would not warranty them because they said I had fuel contamination. They did not send them back to me either. I got 2 more from advance auto parts. They were working fine. For a little while. So now here is where the problem is. I was getting a cylinder 1 contribution code. So I swapped cylinder 1 and cylinder 3 injectors. That code is gone now.
Now I have cylinder 4 contribution code. I swapped 4 and 6. Still have cylinder 4 code. When the engine is cold it runs perfect. When I drive it for about a mile or so and come to a stop sign it's still running perfectly. While I'm at the stop sign it's like someone flipping a switch and then the misfiring starts. And no codes until the "switch" is flipped. Ficm measures 48 to 48.5 at all times. I don't see any chafing of wires. And I forgot to mention that I had a leaking fuel into the oil again. Ran another dye test but did not see any signs of leaks this time. But that was after I swapped injectors around. Could have been leaking from the orings. I can't can't figure out this misfire. So I was thinking compression test next but why does it run fine when cold?
Ford Excursion :: Gas Gauge Not Functioning / Code U1262
Last time I filled up was Friday and the gas gauge hasn't moved. When I shut the Ex off it goes back to the bottom so I know the needle isn't stuck. I'm also getting a code u1262 from the instrument cluster that wasn't there last time I checked so I'm assume it's related. Where to start troubleshooting?
View 6 RepliesFord Excursion :: 2005 V10 - Code PO720 / Alternator Bad
2005 Excusrion V10 6.8L .. Have the PO720 code ..
Replaced alternator it was bad when tested
Replaced OSS - the voltage on this when running varies in the 1.3 - 1.7 range.
What should the ohm voltage read? What would you try next?
Ford Excursion :: Error Code P1201 - EGE Valve?
I am getting an error code of 1201. Is this the ERG valve? How do I change out? Looking for Pictures or diagram?
View 5 RepliesFord Excursion :: 2004 - White Smoke / Code P0401
2004 6.0 Excursion.. I had an issue with lots of white smoke. A p0401 code, then the smoke stopped. I removed the egr and cleaned it. All seamed good until two weeks later. Now I have smoke again. Its seems to be only after it is warm. Do I need a NEW egr valve?
View 2 RepliesFord Excursion :: Misfire - Code P0359 For Coil On Cylinder 9
I recently bought a 2002 Excursion limited v10. It's got a couple of issue, mostly small stuff. The biggest is that it recently developed a pretty bad misfire. The code I'm getting is p0359 which is for the coil on cylinder 9. So I changed that and I'm still getting the same code. I took it to the shop and they're saying that they are not getting a signal on the wiring harness for cylinder 9 and they think that it needs a computer. They want to check all the wiring first to eliminate the possibility of a short or bad connection. My question is, if the coil somehow shorts out against the block, can that burn out the computer?
View 14 RepliesFord Excursion :: 2003 - O2 And O2 Heater Code Flashing On OBD Reader
I am trying to find out how many o2 sensors are suppose to be on my 2003 excursion? I am getting two codes on my OBD reader, an "o2" and an "o2 heater" code flashing...... I have replaced both the o2 sensors i found, both were at the exhaust manifolds.
View 14 RepliesFord Excursion :: Speedometer Malfunction - Generic Code P0500
I have read several of the post on here about speedo's acting up, but I'm not finding anything that pertains to my specific problem. A few months ago I bought a 2000 Excursion, it currently has around 179,000 miles on it. When I got it the ABS light was on and this site is actually where I found out to replace the sensor on the rear end to fix that. My problem is that until a few weeks ago even with the ABS light on my speedo worked just fine and then it started acting up every time I hit the brake pedal and then eventually quit working all together and my cruise control light would flash as well as the OD light.
I replaced the sensor in the rear end and also found out about a recall for the cruise control and had that repaired as well. Now the ABS light is no longer on and the cruise light is not flashing, however the OD light still flashes and 95% of the time my speedo does not work at all. On Monday while heading to town it started working, hit the brakes and all was good, set the cruise control and used it all the way to town, but as soon as I hit the brakes the needle started jumping around and went back to zero and stayed there. I have ohmed the sensors and wires from sensors to harness under the hood and all seems good. The only code I can pull with my meter is P0500 which is just a generic code.
Ford Excursion :: Significant Miss / Code P0306 - COP Replacement?
I developed a significant miss on my '00 Excursion 6.8L yesterday and threw a P0306 code. Since the engine has 178K showing and I bought it used, I am planning to replace all the COPs and plugs.
Recommend one COP over another; motorcraft over Accel, etc.? Any preference for spark plugs?
Ford Excursion :: O/D Light Started Flashing - Code P0743
On the way home tonight, the O/D light started flashing. I happened to have the Bluetooth OBD adapter with me, so I plugged it in and opened Torque. It comes up with a "pending" code of P0743. After a little bit, the light quit flashing so we drove the last mile home. The O/D light began flashing again the last couple hundred feet before our driveway. There didn't seem to be any loss of power or anything like that the whole time.
After we got the kids to bed I went back out to check the fluid level. (It had cooled some, so I let it run a bit before I checked it - the light wasn't flashing this time.) The level is at the second dot, right below the crosshatch. It's almost transparent, but I don't know when it was last flushed (if ever). From what I've seen on here, I'm guessing this is an electrical short somewhere?
Ford Excursion :: V10 Starts Missing From Idle Through To 80 MPH - Code P0358
Had a new V10 Gas engine put in the Ex about three years ago and Been running like a CHAMP....UNTIL.....I'm Driving Back from Halliburton today and my Excursion starts Missing from Idle through to 80mph.. Finally threw an SES Light pulled into the local Auto Parts store and they ran Diagnostic on it and stated P0358... Now I know where to start looking...Only thing is I don't know exactly which one ... What's a good process to eliminate each COP to find the culprit does the #8 at the end designate what cylinder is misfiring?
View 5 RepliesFord Excursion :: Started Spattering And P1280 Code Popped Up?
I did a CCV MOD and washed the engine with simple green and a garden hose yesterday, started the truck and it was running fine for about 10 min. After that it started spattering and a P1280 code poped up. Is it related to a wash or ccv? It does not stoll but idles bad, drives fine once i get it over about 5mph.
View 1 RepliesFord Excursion :: Code P0102 - Mass Or Airflow Circuit Low Input
CODE P0102 "Mass or Airflow circuit low input" That was the code and upon checking my records prior to storing it for the year. I installed a new IAC,MAF, Fuel Pump and lots of new hoses, PCV, Fuel injection regulator. The Vehicle has only 110K miles. Now here is the clincher, after doing just the fuel pump it ran perfect for at least 25 miles, perfect I say. When I shut if off I got the check engine light, and thus the code which led me to install the other stuff. Now after pondering the matter, seems that it acted in a similar way PRIOR to my doing anything but there was no code previously. Like maybe some strange electrical connection, or something.
View 1 Replies