Ford F-150 (2004-2008) :: 2005 - Smoking White - Got Codes P0174 / P0300 / P0305 / P0306 / P0316?
05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.
P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution
Ford Escape / Hybrid :: Check Engine Light Only Comes On After Motor Is At Higher Rev - Codes P0304 And P0316
A couple of weeks ago I got a check engine light. Pulling the codes I saw that it was a p0304 and sometimes a p0316. The first time this happened I check the spark plug cables and one was loose (cycylinder 4). Then last week my fuel pump died. since then I have gotten the two codes on a somewhat continous basis. I replaced the plugs (needed to anyway) and the problem did not go away.
The odd thing is that the check engine light does not come on at idle. IT only comes on after the motor is at a higher rev. The replaced plugs looked pretty normal, but the cylinder 4 plug had some carbon deposits. I am currently running injector cleaner in the gas. I may go ahead and replace the plug wires since the current ones are high mileage and it is not an expensive fix.
Ford Ranger / B-Series :: 2004 - Rough Idle - CEL With P0303 And P0316 Codes?
I love my Ranger. I'm quite impressed with the power and durability. I'm ticked at Ford for stopping production.
I have searched my problem and could not quite narrow it down. I have also tried several remedies with no improvement. I need to narrow it down to a specific item.
2004 Ranger, 4.0 liter, 4x4, 131,000 miles, runs great above idle.
Problem: rough idle, idles at about 750 rpm's. If i raise the rpm's to 850 and up, smooth as silk.
The truck did this a few years back. Not quite as rough and it went away by itself.
Engine light came on this time with P0303 & P0316 codes. I have replaced: plugs, wires, coil pack. I know that the #3 plug is sparking quite well. the #3 injector is getting signal to spray not sure if it is. I have 4 O2 sensors and I believe I tested them correctly (passed). The passenger side upstream or pre cat sensor has not been tested yet. Had to rent a tool and will do that in morning. I slid a piece of aluminum roof flashing between the crank position sensor and the crank pulley. Not a noticeable difference. While at idle (750 rpm's) I pulled each (#3,2,1,) (one at a time) injector wire plugs off the injectors. No noticeable difference. I pulled the vacuum line off the egg and operated it with a vacuum tool. Seems to be working fine. Sprayed carb cleaner around on vac lines. No engine surge
Ford F-150 (2004-2008) :: CEL Codes P0302 And P0316 After Putting Injector Cleaner In The Tank
My 04 F-150 has recently been blowing these two codes. I've replaced the coil pack already and it is still making the check engine line come off. Just put some injector cleaner in the tank last night, so that might take a while to work through. What I should be looking for?
View 8 RepliesFord Escape / Hybrid :: 2002 - Misfire - Getting Code P0305 And P0306?
I have a very Big problem with my Ford Escape 2002 I have this problems code: P0305 accuses Cylinder #5 P0306 accuses Cylinder #6.
I already change the gasket i buy the felpro Kit, and i Also replace all the sparks and spark plug boots, I clean the air sensors and i also replace the EGR, i try to switch cables, and all is the same the car start buy when i accelerate it just go off, i don't know what can i do next, somebody told me to change the fuel injector, i take the pressure in both spark holes the number 4 was 150 and the 5 and 6 was 120, No leaks oil. My car is a Ford Escape 2002, XLT 3.0 4x4
Ford F-150 - 1997-2003 :: Codes P0304 And P0316 - Lean Bank 1 And 2
2003 F150 v6 2wd 170k ... For a year I've only had codes P0171 and P0174 (lean bank 1 and 2). I was told it wouldn't hurt anything... I think now I should have taken care of it.
Anyway 3 weeks ago my truck started running a little rough. It was sputtering and had trouble getting up to speed, sometimes also the air switches from vent to defrost until switch gears and rpms go down. It gradually got a lot worse over 10 days while part was otw. A week ago i changed MAF and cleaned the black thing it's inside of. It started running better but still not good. I pulled my small trailer 2 days ago and it got worse after dropping the trailer.
Today checked codes at AZ and lean codes are gone and have p0304 (#4 misfire) and p0316 (crank sensor problem). Is this related.? Also Right before all the trouble I changed battery and alternator. Also i read online that MAF needed 2 weeks to relearn the way I drive to get correct gas/air ratio? Is that correct?
Also I read so many different things I needed to do during installation... Some say I need to turn key to the on position after unplugging old MAF then plug new one in... turn key to on position 10 times, Rev up engine, drive it rough for the first 2 minutes... etc. Is there a correct way to do it or is it vehicle specific?
Should I start by changing spark plugs and coils? The guy i bought it from and trust said he changed spark plugs right before I bought it. Will it ruin truck if I drive it? I've read so much but everyone says so much different things on the same topic. I'd what to start with or if this is related.
Ford F-150 - 1997-2003 :: Codes P1518 / P0316 / P0303 And P0136?
I have a 2003 F150 V6 4.2L, 171,000 miles on it. I have four codes on it.
#p1518
#p0316
#p0303
#p0136
I had a p1518 in november of 2012, had it repaired and its back. In the time that I had it repaired and it came back on (maybe a month and a half ago) I only drove the truck maybe 3000 miles, if that. Just curious if this particular part should have some kind of warranty either by the MFG or dealer since the dealer repaired it. Have a limited budget, trying to find out what I can fix on my own in a timely manner.
Ford Ranger / B-Series :: 2003 - Misfiring On Start Up - Got Codes P0316 And P0304?
My 2003 ford ranger 3.0 v6 is having a misfire on start up and it is located in the forth cylinder. Where to start to get rid of this problem. i have already changed all my plugs wires and even the coil pack cleaned out the maf and looked for possible leaks. the car shakes really bad at lights and the check engine light starts to flash. Need diagram of where all the cylinder numbers are at and maybe the firing order?
View 14 RepliesFord Excursion :: When Parked Facing Uphill Start Rough And Sputters - Codes P0316 / P0306 And P0301?
I have a small problem that has been going on for about the last 6 months. It only appears once in a while, and only when I have parked facing uphill for longer than a day or so. Upon first start (cold) after sitting pointed uphill for a day or two, it starts real rough and sputters a bit. Then when I check codes, I always have a pending P0316 (misfire within the first 1000 revolutions) along with a P0306 or P0301. No dash lights or anything.
Since those two cylinders are at the front of the motor, could it be that the fuel is leaking back down the rail and leaving those two injectors dry? It isn't always both cylinders, sometimes one or the other. If this is the sign of something bigger on the horizon, I would like to have a heads up.
Ford F-150 - 1997-2003 :: Got Codes P0453 / P0232 / C1303 / P0305 - Changed Fuel Pump?
I just checked my computer I have a couple codes
P0453 evap emission system pressure sensor/ switch high
P0232 fuel pump secondary circuit high
C1303 right front isolation clamping circuit..
P0305 cylinder 5 misfire.
I changed the fuel pump 2 days ago and the coil on cyl 5.
Golf IV R32 :: Cylinder 5 Misfire Codes P0300 And P0305
So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.
View 3 RepliesTouareg :: 2001 - Getting Consistent P0305 And P0307 Misfire Codes?
I'm getting consistent P0305 and P0307 misfire codes when my 4.2L engine is revved past 5,000 RPM. Have a done a bunch of diagnostics including a new timing belt to no avail.
Specifics:
I have 2001 Audi A6 with a 4.2L 40V engine (yes, I know it isn't a Touareg but the motor is the same!). Timing belt replaced about 1.5 years ago and it runs great. However, I'm getting some codes. 1) At high RPM (over 5,000 rpm) under load, I consistently get a P0300, P0305 and a P0307. Happens like clockwork. As soon as I hit 5,000 rpm, those three codes post. 2) After driving around for a bit, I get a P0340 (Cam position Sensor). Things I have done, all with no change: 1) Checked for Vacuum Leaks 2) Replaced all the spark plugs 3) Moved all the coil packs from one side to the other 4) Replaced the Cam position Sensors 5) Moved all the injectors from one side to the other 6) Inspected (as best I could) the variable cam timing system under the valve covers. Brown chain guides looked OK.
Finally, I changed the timing belt to no avail. When I disassembled, I found the motor was perfectly in time. My marks from the first change ~18 months ago were still in place and everything lined up. I was able to install the crankshaft lock and cam locking bar with the timing belt in place (it wasn't even off a fraction, the locking bar slid right in). I installed a new belt and all the rollers + tensioner. Didn't put in a new water pump but changed all the other pieces. The new install went great and I was able to get almost exactly the 5mm gap on the tensioner after spinning the motor a few times that Bentley talks about. Put it back together and took it for a spin. DARN!@ The same codes post at exactly 5,000 RPM: P0300, P0305, P0307.
Ford Escape / Hybrid :: 2004 2WD Stalls Out - No Codes
2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
Avalon 2005-12 :: 2007 - Skipping And Running Rough / Error Codes P0305 And P0355
Our 2007 Avalon with 65xxx miles on it was skipping and running rough this morning. Running a scan with my VAG-COM gave me these codes.
Mode 07: Pending emission related fault codes Address 7E8: 2 Faults Found: P0305 - Cylinder 5: Misfire Detected P0355 - Ignition Control Circuit for Cylinder 5: Malfunction
Would you say it is time to replace the Coil for this cylinder, or should I do more troubleshooting first?
From what I've read on this forum, it appears cylinders 1, 3 & 5 are at the rear of the engine and are a PITA to change. Is there a good write-up or video on how to change these at the rear of the engine?
Ford - Escape :: 2004 V6 Misses / Bucks And Jumps - Multiple Check Engine Codes
This is a Ford Escape XLT with the 3.0L V6. I get the following codes - P0316 P0300 P0136 P0305 P0306. Sometimes it runs just fine and sometimes it misses and bucks and jumps. It has been taken to a local shop and they said they found a loose ground at the computer. They said they corrected this and it should run fine. It still shows the same codes and runs like it did before they worked on it.
View 10 RepliesFord F-150 (2004-2008) :: 2006 - Random Misfire Code P0316
Friend has a 2006 with the 4.6 motor. From time to time he gets a random misfire code ( I think its 0316).. He claims it will only do it when the gas tank is less that half full. I don't see any correlation between fuel level and the code. I am going to check fuel trim values, etc, when the code is set, this weekend.... all I can assume is low fuel pressure which sets the code... Any problem with the pressure module or fuel pump / discharge hose that is related to low level in the tank ?
View 3 RepliesFord Escape / Hybrid :: 2002 - Random Misfire Codes
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 RepliesFord Escape / Hybrid :: 2001 3.0L Engine Has A Miss - No Codes?
What to look for. 2001 escape 3.0 starts and runs but it has a miss and no codes came up yet . the engine will rev up but it really takes time to idle down . don't matter if its cold or hot it just don't want to drop to idle as fast as it should.
View 4 RepliesFord Escape / Hybrid :: 2001 - Stall After Fueling - No Codes?
I have a 2001 Escape 3.0 l 6 cyl. She stalls or almost stalls every time I fuel up. I found if I turn key but not to start, it only severely sputters and usually doesn't stall. Replaced EVAP canister (and all but dust separator inside), fuel pump, EGR valve, pcv tube, iac, upper gaskets, valve cover gaskets, seals, spark plugs, fuel/air filter, evap purge valve, fuel filler cap, ftp sensor, all ignition coils, checked for clogged fuel filler neck, fuel/vent hoses from/to evap canister...nothing worked.
There is a hose I cant get to that ends unattached just past fuel tank and near fuel vapor(?) "tee" under car. Seems to come from fuel tank. What is it? Just an overflow vapor hose? Should it be attached to something? Anyway, I suspect fuel vent hose or valve on top of fuel tank since my options are limited now. Have it running great (except this issue) with 260,000 miles so really don't want to spend mucho $$. No codes thrown.