Avalon 2005-12 :: Error Code P0355 Diagnosed

2006 Toyota Avalon 72000 miles

Plugs and coil have been switched between Banks 1,3,5 with 2,4,6 code P0355 shows the same cylinder 5 after the switch. What's the difference between a PCM and ECU and which one do I have.

View 2 Replies

Lexus RX 2004-09 :: P0355 Error Code And Potential Misfire Codes On All Cylinders

I am getting P0355 error code and potential misfire codes on all cylinders. Engine light and VSC stays on now. Idle is unstable and power is a little jerky at times. I bought a Denso direct ignition coil to replace, however, Cyl 5 looks difficult to access.

View 3 Replies

Avalon 2005-12 :: Misfire And Check Engine Light Came On - Car Is Running Little Rough

My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.

View 1 Replies

Ford F-150 - 1997-2003 :: 1999 - Misfire / Running Rough - Code P0305 And P0174

Here is my situation : I have a F150 1999 4x4 ext cab with 326 000 km. A little while ago I got a P0401 code so I decide to clean the TB first and at the same time change plugs and wires since they were overdue. The same code came back and a misfire. Ordered EGR valve, DPFE sensor and selenoid. Realize that I had ordered crappy plugs by mistake. I change all plugs. Had to wait for the EGR valve and others to arrive. I drove the truck for a while since I did not have the time to change the valve and others, during that time the misfire did not come back. Yesterday I change the EGR and others. Today I get a truck that runs really rough and got new codes , P0305 and P0174. I'm really confused now on what should be my next step, should I change the coils, can a P0305 cause a P0174. Should I change vacuum hose going to the EGR , selenoid and DPFE.

View 12 Replies

Ford F-150 (2004-2008) :: 2005 - Smoking White - Got Codes P0174 / P0300 / P0305 / P0306 / P0316?

05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.

P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution

View 3 Replies

Ford Fuel System :: Running Rough - Skipping / Surging And Die

I built the 400 in my 79 a couple years ago and it runs very well...until yesterday. I'm about 80 miles into this tank, and on my way home from work, I thought I felt a vibration (not in the steering wheel, but in the front oc the truck). Then the engine became evident it was running rough and was skipping and surging. I stopped.

It idled pretty rough, then died. Fired right back up, ran rough, and died. Sometimes it would idle smooth for several seconds (20-30) then start surging and skipping and die. I could hold a little throttle and it would run about the same, except some backfiring in the exhaust (more like a big hiccup).

The carb is a 670 Street Avenger with nothing really done to it. The bores are really black (not sooty, more damp or so). I have always used the air filter, so that's odd. I took the carb off and removed the bowls. Nothing inside has a dirty or clogged appearance at all. Not sure if I should completely rebuild it.

View 6 Replies

Ford F-150 (2004-2008) :: Running Rough And Skipping After Plug Change?

I just completed a successful second spark plug change, using Motorcraft SP515 plugs just like last time. After reconnecting battery and starting engine, it ran poorly throughout a short road test. Felt like it was skipping. Checked under the hood and found that the #2 fuel injector was disconnected, so I reconnected the injector.

I took another short road trip and it still ran poorly as if skipping. So, this time I disconnected the battery for several minutes while removing the #2 plug thinking I may possibly have fouled the plug by the injector not being connected. I also checked all of the other injector and coil connections. Reconnected battery and took another short trip. It still runs poorly. No codes yet.

View 14 Replies

Ford Super Duty (1999-2016) :: 2005 F250 - Running Really Rough When Engine Not Fully Warmed Up - Glow Plug Codes

2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?

View 7 Replies

Avalon 2005-12 :: CEL Error Code P0440 Error Code / Charcoal Canister Replacement

So of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?

I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.

View 2 Replies

Avalon 2005-12 :: 2009 - Navigation DVD Showing Error?

We just purchased seemingly well cared for 2009 Avalon XLS. Navigation system is showing a DVD error (unable to read). First we thought it was missing the DVD then we discovered the DVD port in the truck and through some trial and error got the DVD (#U52) out. We are proceeding with the logic that the DVD is bad.

View 6 Replies

Avalon 2005-12 :: Check Engine Along With VSC Lights Came On - P2195 Error

I own a 06 limited and my Check engine along with VSC lights came on. Autozone read the code and it is a P2195 error. According to AZ the O2 sensor cost $500, according to websites the fix is O2 sensor and manifold ~$1800. I don't have that much money. The dealer told me that it was ok to drive with warning lights on. I checked the MAF sensor and it is clean. The O2 sensor or A/F sensor Stuck Lean - bank 1 sensor 1. If I want to do the work myself, any diagrams, picts, instructions etc......

View 8 Replies

Avalon 2005-12 :: 2006 LE - VSC / Check Engine Light And Cruise Error

I try to do my own maintenance. I have a 2006 Avalon Limited. This has happened twice recently, using cruise it has kicked off and gives me the VSC light and the check engine light and cruise error, when running codes I get the following P0138 & P2195 both have to do with the O2 sensor on bank 1, and P1578 & P1201 which are brake malfunction. I have been searching the Internet for any information on what could be causing my issue with no luck. I have a 3000 mile trip and need to figure this out soon.

View 14 Replies

Avalon 2005-12 :: Check Engine Light On - P0015 Error Code

I have a CEL on my 2007 Avalon so I decided to take it to Autozone to get a scan. Error code P0015 was returned. This code has to do with B Camshaft Position, Timing Over Retarded (Bank 1). I've done a little research and I've read that this could possibly from a dirty screen on the Oil Control Valve, the OCV itself, or the Cam Position Sensor. Before replacing parts, what I would like to do first is to check/clean the screen on the OCV. Secondly, I would like to swap the Cam Position Sensor to a different bank and see if the other bank throws an error. If the other bank throws an error, then I know the sensor is bad and needs to be replaced. With this said, I am having trouble locating the OCV and CPS. Where the valve and sensor is located. A diagram would be useful.

View 14 Replies

Avalon 2005-12 :: P0031 Error Code / Part Number For O2 Sensor?

I have a check engine light come on in my 07 Avalon and had the car scanned. It was throwing error code P0031. I'm gonna go ahead and replace this O2 sensor, however, I'm having a hard time finding the correct part# for this sensor.

View 1 Replies

Golf IV R32 :: Cylinder 5 Misfire Codes P0300 And P0305

So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.

View 3 Replies

Ford - Escape :: 2004 - Codes P0316 And P0305

I am having the above codes come up P0316 and PO305. The car is running rough...just started tonight. The check engine light started flashing but it's on continuously. Of course when I had the codes read at a Firestone they gave absolutely no support as to what it could be.

View 17 Replies

Avalon 2005-12 :: VSC / Check Engine Light Comes On After Rain - E3 Error With Cruise Control

I have an '05 I bought 3 years ago and any time it sits outside and gets rained on, the VSC/check engine light comes on when I start it and it doesn't go away for 2-3 days at a time. The frustrating part is that any time this happens, I get the E3 error with the cruise control even though there's not a drop of water to be found anywhere.

View 6 Replies

Avalon 2005-12 :: 2006 - Error Code P0031 / Heated Oxygen Sensor Is Bad

I received error code P0031 on my 06 Avalon the other day. It states that the HO2S (Heated Oxygen Sensor) is bad. Bank 1 Sensor 1. I located the sensor but have a few questions...

Just to give an over view for those that don't know where these are, there are 4 sensors the one in the front on the manifold (upper - B2, S1), (lower - B2, S2) and the rear manifold (upper - B1, S1), (lower - B1, S2).

All of the sensors look the same with 4 wires. what the part number is for the sensor? Also since this is the hardest one to get to, I would like to know where the wire routes to. I found the wire up to the connector on every other sensor except the one I need (B1S1). It looks like it runs towards the top of the engine but from the top I don't see it.

View 2 Replies

Touareg :: 2001 - Getting Consistent P0305 And P0307 Misfire Codes?

I'm getting consistent P0305 and P0307 misfire codes when my 4.2L engine is revved past 5,000 RPM. Have a done a bunch of diagnostics including a new timing belt to no avail.

Specifics:

I have 2001 Audi A6 with a 4.2L 40V engine (yes, I know it isn't a Touareg but the motor is the same!). Timing belt replaced about 1.5 years ago and it runs great. However, I'm getting some codes. 1) At high RPM (over 5,000 rpm) under load, I consistently get a P0300, P0305 and a P0307. Happens like clockwork. As soon as I hit 5,000 rpm, those three codes post. 2) After driving around for a bit, I get a P0340 (Cam position Sensor). Things I have done, all with no change: 1) Checked for Vacuum Leaks 2) Replaced all the spark plugs 3) Moved all the coil packs from one side to the other 4) Replaced the Cam position Sensors 5) Moved all the injectors from one side to the other 6) Inspected (as best I could) the variable cam timing system under the valve covers. Brown chain guides looked OK.

Finally, I changed the timing belt to no avail. When I disassembled, I found the motor was perfectly in time. My marks from the first change ~18 months ago were still in place and everything lined up. I was able to install the crankshaft lock and cam locking bar with the timing belt in place (it wasn't even off a fraction, the locking bar slid right in). I installed a new belt and all the rollers + tensioner. Didn't put in a new water pump but changed all the other pieces. The new install went great and I was able to get almost exactly the 5mm gap on the tensioner after spinning the motor a few times that Bentley talks about. Put it back together and took it for a spin. DARN!@ The same codes post at exactly 5,000 RPM: P0300, P0305, P0307.

View 6 Replies