Corolla / Matrix 2009-13 :: Rattling In Front Brakes When Cruising Along At Almost All Speeds
I have a 2010 Model S that has 38,000 miles on it. I am hearing a rattling in the front brakes when cruising along at almost all speeds. If i hold a little peddle pressure it goes away. Sounds like the pads are rattling to me. I am running the stock pads with about 45 to 50% remaining on them.
View 6 RepliesFord Brakes/Suspension :: 2005 F250 Front Brakes Calipers Are Locking Up
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 RepliesFord Brakes/Suspension :: Smell From Brakes And Left Front Rotor Hot
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 RepliesFord Brakes/Suspension :: Front Brakes Locks Up / Tires Screeching
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
Ford Brakes/Suspension :: Front Brakes Are Dragging / Does Not Stop The Truck Just Gets Hot
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 RepliesFord Brakes/Suspension :: 2003 F350 - Changing Front Brakes / Have To Remove Hub Or Lockouts?
I've changed brakes on tons of front wheel drive cars, and two wheel drive trucks. But NEVER on a 4wheel drive Super Duty. My truck needs new front brakes now!!!! its a 2003 F350 4X4 -58,000 miles. I was just wondering from you all, how hard is it to change brakes on a 4x4 truck? Do I have to remove the Hub or lockouts?
View 5 RepliesFord Brakes/Suspension :: Front Brakes Build Up Pressure And Slowly Start To Lock Up / Not Releasing
Initially when I start driving, the brakes work just find. But it seems as I use the brakes, the front brakes build up pressure and slowly start to lock up. They don't lock up completely, but they do cause a significant amount of drag. The rotor, calipers, rubber hoses and master cylinder are all very new. I'm thinking maybe the issue is with the master cylinder and am considering going to get one along with a brake booster(since it doesn't have one currently).
View 14 RepliesFord Brakes/Suspension :: 1997 E350 2wd - Both Front Brakes Getting Hot
Drove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
Ford Brakes/Suspension :: Faint Grinding Noise When Turning The Steering Wheel At Low Speeds
One my F350 with 175,000 miles on it, at low speeds when turning the steering wheel it seems as if it has two places during use that it rubs or has an oblong spot in it. I have 285 tires on it and have for years.
Kind of like if you were turning a shaft in a seal and it rubbed or was rough. It makes a faint, muffled, barely audible grinding noise or feel. I have a lift and level of about 4" and 285s for years. This just started in the last 5 months or so.
Ford Brakes/Suspension :: 1977 - Tire Diameter - Gear Ratio Before And After?
Never been on a forum but I've got a 1977 ford f150 with a 400,c6 trans currently with 3.50 gears and 26.5 overall dia tires. if I was to put 34.5 inch tires and 4.56s would it drive like it does now, same speeds and rpms in all three gears and it shouldn't chug more gas than it already does... right?
If im reasking a question post link haven't found one.
Ford Brakes/Suspension :: Gear Box Leaking And Getting Some Noises When Making Turns
I've noticed my Gear box in the truck seems to be leaking and been getting some noises when making turns too that i can feel in the steering wheel more than hearing it. (not like air in the system or over steering things like that).. feels more like a grinding feeling.. anyways.. ive had a couple people recommend Redhead gear boxes.. but hadn't ever heard of them till they told me about it.
So was wondering what you all think about the company and for the ones that have gotten them any major issues?? Biggest thing I keep seeing on non-factory gear boxes are mentions of sloppy steering.. they can't be adjusted.. quick failures.. etc. etc... Worried I'd be wasting money getting something not-stock than if I'd had just bought it right from ford...
Ford Brakes/Suspension :: Clunking And Rattling In Front End
I have had a clunk in the front end that started out as a light clunk that was sometimes noticeable. It has now turned into a clunk that can be heard very often. It sounds like a hollow clunk. I'll try to explain it so it makes sense...If I'm going over a bump or speed bump or something like that it doesn't really do it noticeably. If I'm driving a get to a place where the road is uneven or there is a hole or pothole and the front end seems to "fall into the hole", then the sound is very audible, and I can feel it slightly in the steering wheel and under my feet in the drivers floorboard. So, I've had the front end checked out 4 times and between what they said to do and what I've read on here...here is what I've done so far......
Changed end links with moog end links
Changed sway bar bushings with moog bushings
Undid the bushing mounts from the front frame and wired the sway bar up to keep from flopping around. No change in sounds
Didn't get rid of the clunk....
Had front end shop check out truck... They said ball joints were ok, no play in them. They did say that they could feel some "clicking in the pitman arm pivot" when turning the wheel. Like something was loose in box.
I've changed shocks and bearings.
I can grab a hold of the passenger outer tie rod at the adjustment sleeve and rotate the tir rod and it will rotate around in the socket and hitting on the insertion point and make a metal thud sound.
Again, took into shop and they said that would be normal b/c the tie rods have to have that to keep from binding up in front end.
My thinking is that if the tie rod rotates that much, then it is rotating the drag link which in turn puts stress on the pitman arm which in turn has either broken or sheared the pinion shaft inside the box and then when I go over a hole, it moves and all of the above is put into motion.
Shop (Ford) basically called me an idiot and that wouldn't be the cause.
So, now onto my thoughts and questions....
Radius arm bushings
Axle bushings (????? how many and where are they all located)
tie rods and drag links..
Ford Brakes/Suspension :: Replace Front Springs With Airbags
I am lowering the front end of my truck 3" using DJM Dream Beams. I have cut out the rear springs and replaced them with a four link lowering it 4" and installing an air bag suspension. I would like to run air bags up front, as well, but haven't been able to find much about that. What size to use?
View 7 RepliesFord Brakes/Suspension :: 1982 F150 - Shake Going On In The Right Front
I've got serious shake going on in the right front. I ordered new wheel bearings but can't figure out how to replace them. Been working on tractors, trucks, boats my whole life and this is embarrassing. '82 F150 straight 6, 4wd, standard trans.
View 4 RepliesFord Brakes/Suspension :: Hub Locking - Bang From Front End When Engage 4WD
I have been having hub locking trouble and finally located a bad vacuum hose. Hose has been replaced. Now when I engage the 4WD and apply a little power, I get a terrible bang out of the front end, then the truck moves on. Sometimes there is a second bang, sometimes not. The chain appears tight in the transfer case and the ujoints look ok. I have turned the wheels with hubs locked one at a time and the joints are free.
View 9 RepliesFord Brakes/Suspension :: Dual Or Single Shocks Up Front
I have dual fabtech shocks in the front with 10" lift. I want to switch to all icon shocks. I think just the monotube, or are the remote reservoir going to ride a lot better? Would I be better off going back to single shocks in the front or keeping duals?
View 1 RepliesFord Brakes/Suspension :: Steering Very Sloppy / Front End Wobbly At A Low Speed
I have a 2002 ford f350 sd crew cab, i have changed the front and rear brakes, since then the steering has gotten sloppy. I was driving around 30-40mph and making a sweeping right turn and the front end was wobbly at a low speed it is fine and on a left turn it is fine. It feels like it is the drivers side tire that is the problem. I have to change the tie rod that is attached to the pitman arm. I don't want to bring it to a shop.
View 7 RepliesFord Brakes/Suspension :: 2000 2WD - Front Brake Scraping While Driving
2000 Explorer 2WD. I had tons of front end issues that I have been working through. So far I have done upper control arms, upper and lower ball joints, tie rod ends, got an alignment. The steering/suspension system is in good shape now.
Now the only thing left is a scraping/grinding sound coming from the driver's side brakes. I mostly hear it at low speeds (taking off from lights, etc).
When I was doing all of the other work, I observed that the rotor is in great shape, brake pads look great. I am wondering if it is a caliper issue, maybe the caliper isn't releasing enough or something. What to check?
Ford Brakes/Suspension :: Front Brake Rotor Removal / Replacement
I'm trying to replace the front brake rotors on a 97 Ford Explorer (AWD, 5.0 L). I've removed the calipers and pads - but can not loosen the old rotors. It looks held on by rust - but do I need a special rotor pulling tool?
View 8 Replies