Ford Brakes/Suspension :: Front Brake Rotor Removal / Replacement
I'm trying to replace the front brake rotors on a 97 Ford Explorer (AWD, 5.0 L). I've removed the calipers and pads - but can not loosen the old rotors. It looks held on by rust - but do I need a special rotor pulling tool?
View 8 RepliesFord Brakes/Suspension :: 1996 F350 Pulling To The Left When Apply Brakes
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
Ford Brakes/Suspension :: 2002 - Brakes Pull To Left Always?
This is on my 2002 Ford Excursion 4x4. I have replaced the brakes 2 times with the same results.
New: rotors, pads, calipers and grease the caliper slide pins so they are sliding properly. I have also replaced the slide pins the first time. I even lightly greased the ends of the brake pad back plates where they mount in the calipers/brake clips. There is always more brake dust on the left front wheel compared to the right front. The steering wheel turns to the left when I hit the brakes. I can't figure this out.
The one thing that seems strange is it was very difficult to get the pads and brake pad clips into the caliper. It almost seems like the pads are too tight into the clips/caliper. I am wondering if taking a little material off the ends of the brake pad back plate to allow better movement in the caliper/clips.
The left front is either grabbing too much or the right front is not grabbing enough.
Ford Brakes/Suspension :: 2007 Expedition - Rear Rotor Removal
I need to change the rear brake pads on a 2007 Expedition and was going to turn the rotors also. It appears the rotor is held onto the axle by a large nut and not having done any brake jobs in several years, I've never run into a rear rotor that's bolted on. Is this the case and if so, what size socket do I need to get it off. Also, I was curious if there is anything else I need to know before I dive in. I heard it was difficult to get off.
View 7 RepliesFord Brakes/Suspension :: 2008 F350 - Front Left Wheel Locking Up Intermittently
2008 F-350 wheel will lock for no reason. I think the Hydroboost has a hair line crack it and when the temp and pressure reach a certain number then it sends brake fluid threw the crack to the caliper? I also heard it could be in the ABS because its locking just one wheel?
View 1 RepliesFord Brakes/Suspension :: 2005 F250 Front Brakes Calipers Are Locking Up
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 RepliesFord Brakes/Suspension :: Front Brakes Locks Up / Tires Screeching
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
Ford Brakes/Suspension :: Front Brakes Are Dragging / Does Not Stop The Truck Just Gets Hot
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 RepliesFord Brakes/Suspension :: 2003 F350 - Changing Front Brakes / Have To Remove Hub Or Lockouts?
I've changed brakes on tons of front wheel drive cars, and two wheel drive trucks. But NEVER on a 4wheel drive Super Duty. My truck needs new front brakes now!!!! its a 2003 F350 4X4 -58,000 miles. I was just wondering from you all, how hard is it to change brakes on a 4x4 truck? Do I have to remove the Hub or lockouts?
View 5 RepliesFord Brakes/Suspension :: Front Brakes Build Up Pressure And Slowly Start To Lock Up / Not Releasing
Initially when I start driving, the brakes work just find. But it seems as I use the brakes, the front brakes build up pressure and slowly start to lock up. They don't lock up completely, but they do cause a significant amount of drag. The rotor, calipers, rubber hoses and master cylinder are all very new. I'm thinking maybe the issue is with the master cylinder and am considering going to get one along with a brake booster(since it doesn't have one currently).
View 14 RepliesFord Brakes/Suspension :: 1997 E350 2wd - Both Front Brakes Getting Hot
Drove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
Ford Brakes/Suspension :: 2004 F150 - Front Left Wheel Would Start Shaking When Brake
Two weeks ago my front left wheel would start shaking like hell when I brake, not at first but after say may eight miles of driving. I have never been in a vehicle shaking so violently and after proceeding from a stop it would continue until it cooled down. I tore out the caliper and made sure everything was clean and lubed and also to make sure I did not put the pads on wrong. Fast forward one commute and the same crap. I could not go faster than 45 mph without feeling like it was going to disintegrate.
When I got home the damn thing was smoking. I managed to get it to the dealership this afternoon and two hours later the guy told me that the guides just needed some cleaning and grease. They did not want to charge me anything (draw your own conclusion) for it. I was told they drove it up/down hills and it was alright. I left kind of suspicious and four miles later the problem revealed itself again. My next thought it maybe axle end play, bad bearings or joints? Intermittent why? 2004 f150 lariat 4x4 ....
Ford Brakes/Suspension :: 1999 F350 - Brake Shoes Contacting Rotor (dragging) When Engine Is Off
I changed over to summer tires today on my 1999 4wd F350 diesel . While the front tires were off of the ground, I tried rotating the wheels by hand to see what the resistance was like. I was surprised at how stiff they were. It would take three fingers to rotate the wheel and as soon as I stopped applying pressure the wheel stopped turning. I pulled the rims off and found that the calipers appeared to be contacting the rotors and causing resistance.
My last rig was a 1960s 4wd F250 that had calipers that could be adjusted manually. I kept these adjusted so the calipers were almost touching the rotors. I could spin the rims with one finger and the wheel would turn for 30 seconds or so until coming to a stop. Is this normal?
Ford Brakes/Suspension :: Front Left Steer Is Making A Lot Of Noise And Wearing On Tire Inside Edge
I bought a 2002 F250, 2 months ago love the truck drives great for 130000 miles, but the front left steer is making a lot of noise and wearing on the inside edge and like its skipping every couple inches so very noisy thought maybe ball joints but a buddy say tire is out of balance truck does not pull left or right and drives straight...
View 3 RepliesFord Brakes/Suspension :: 1997 F150 - Converting Drum Brakes To Rear Disc Brakes?
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Ford - Brakes - Escort :: 1996 - Grumbling Sound After Front Pad / Rotor Replacement
The shop replacing my front tires advised me to replace my front brakes and rotors soon. I'm not a huge car repair person, but I remembered my father-in-law saying brakes aren't that bad to work with. The car is the "college beater" I bought ten years ago and I'm trying to keep investments in it minimal. I told the shop I would do the brakes myself. So I spent the weekend with the Haynes manual fussing with overtorqued lug nuts, rusted on rotors, tightly wedged guide pins, and outer pads that didn't seem to have room (not the piston side). Got everything assembled, bled the caliper that was disconnected, and took it for a test drive.
I got about 30 feet from the driveway before pulling back in. The front of the car was making an grumble sound and had an odd vibration like a flat tire. This was with brakes engaged and not engaged. The car stopped fine, but I probably didn't get above 10 mph. Is this part of the "bedding/seating" process? I put in new (cheap) rotors and pads. This afternoon I'll check to ensure the pads are in properly and aren't dragging on the rotor and that I have the wheels properly centered. Car is a 96 Ford Escort 2 door hatchback.
Ford 7.3L Power Stroke (1999-2003) :: Brakes Overheating - Front Right Rotor And Hub Very Hot
I was driving on a short business trip and I noticed what I thought at first was clutch smell, and then I realized I had a brake overheating. I pulled over and the front right rotor and hub were very hot. The caliber not so much. I let it cool while I was at the meeting. About 1 1/2 hours later I jacked the truck up to see if the bearings felt bad. Seemed fine so I drove home trying not to use the brakes and the heat did not return. I replace the caliber with one from Ford, but the only lines I could find were from CARQUEST and they are made by Raybestos. I am assuming that these lines are made in China.
I have been looking for some braided SS lines, but can't find any for a 2 wheel drive dually with 4 wheel ABS. Where I can order some better lines???
I hated my old 1994 F-350 that had those Metal/rubber pins, they would mess up and overheat also, I thought that my 2000 would not have this problem, I was wrong.
FYI, about a month ago I replaced the rear pads, and changed all the brake fluid with Valvoline synthetic DOT 3. I installed Akebono pads on the rear and just today Akebono on the problem front side. Will change out line and pads on driver side later this week. I hope I got if fixed.
Ford Brakes/Suspension :: Rear Brake Sticking / Hot Smell
I was fueling up my 06 F-250 yesterday and smelled hot brakes. I checked and found the right rear was really hot. After it cooled down I was able to drive on home and it was not too hot when I got here. I was towing a trailer with my tractor on it so I had a pretty good load. It was over 6 miles to my house with stop and go traffic and no hang up. What should I do to keep this from happening again? I don't drive this truck much but when I need it, I need it to be dependable. It has 99k on the clock and is a gas job.
View 1 RepliesJeep - Cherokee :: Front Disc Brakes Are Creating A Small Amount Of Drag On Rotor
My front disc brakes are creating a small amount of drag on the rotor. With the car jacked up and wheel off I am able to easily turn the rotor by hand, but there is a small amount of drag. I haven't had any problems with my brakes, they have never frozen or overheated, etc. I put new brake pads and rotors on the front about 6 months ago only because it was time for replacement. The question is: how much disc brake drag is acceptable? Looking around on the internet for answers there doesn't seem to be a consensus: some people say absolutely no brake drag, some say that a small amount is normal. What do you think?
View 6 Replies