Golf V R32 :: Rubber Weatherstrip Falling Off The Door Very Frequently
So the black weatherstrip that goes around the door falls off along the bottom of the door (especially the driver's side) like once or twice every year? I've had the dealer replaced brand new ones twice already and re-glue them another 2-3 times but seems like it just wont' hold on to the door. Now I am out of warranty and the weatherstrip just fell off again, try to see if there's any solutions to this.
View 5 RepliesFord Aerostar :: Clock Spring Swap?
I have a 1992 Aerostar Sports edition. My clock spring went bad like 6 months ago. I couldn't find a replacement anywhere. Not even at the Ford. I went to different junkyards and couldn't find the same exact one. Since I wanted to change the steering wheel anyway, i got the steering wheel and the clock spring from a 1999 Ford Explorer Sport at the junkyard. The clock spring fits perfectly and so the steering wheel. My only problem is that clock spring harness is different. I have no problem with the steering wheel side since both the steering wheel and the clock spring came from the same car. But under the dash is a different story. I have the manual for my Aerostar with the wiring schematic for the speed control system (cruise control) and horn but i just can't find the one for the 1999 Explorer. I got one for a 1996 Explorer and have the same wire colors than the clock springs i got from the 1999 Explorer. But i want to make sure I got the right schematic to feel confident I'm doing the job right. I can also use another version for the 1992 Aerostar because mine is a little confusing.
My old clock spring had two harnesses. One for the airbag which I am not going to use (i don't like airbags) and a second one for the cruise control/horn. This harness had four wires. One thick black one that goes to the casing of the ignition switch, and three smaller wires (BK, LB/BK, and Y/LB). The clock spring from the 1999 Explorer has six wires on that harness. One thick black that goes to the ignition switch and five more smaller ones (BK, LB/BK, DG/O, Y/LG, and R/BK). Going by the two schematics i have them figured out (i think), but want to make sure.
Ford Aerostar :: Rubber On Metal Like A Flat Tire - CV Axle Broken
Have a 95 aero E4wd. Have replace driver side cv axle and drove about 8 miles then the outer joint broke. Had mech change cv axle and drove about 2 miles and the inside broke.. Same mech replace it and drove 3 mile and heard like rubber on metal like a flat tire. The cv axle did not break and won't turn when in gear. Back to shop with aero. Lifted on lift and jacked up front and rear. Turned the driver side and the passenger turned with it also it turned easy. Started it up and placed in gear, all were rotation except driver side , it was hung up. What should be fixed on diff?
View 14 RepliesFord Super Duty (1999-2016) :: 2003 - Clock Spring Has 8 Spring Wire?
Adding cruise control to F350 XL I just bought. I got a steering wheel with the buttons. But I am having problems with the clock spring. Mine has an 8 wire plug with only 6 pins on the big plug and all of the clock springs I have found have only a 6 wire plug for the big one. Without changing my clock spring I have no where to plug in the cruise wiring. All have been for right year model with cruise and even tried different years but none will plug in under the dash.
View 3 RepliesFord Super Duty (1999-2016) :: Conversion Of Leaf Spring To Coil Spring?
Conversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!
I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.
Ford Fuel System :: Gas Line Spring Lock Coupling - How To Release Garter Spring
I hope i don't give the impression on my very first post that I'm a total retard......but ...I can't figure out for the life of me how to get those spring line coupling apart! I've removed the clips...but it just won't pull apart. Is there a tool to release the garter spring?
View 4 RepliesGolf IV / Jetta IV :: Rear-view Mirror Keeps Falling Off
As the title indicates, the rearview mirror (that mounts on the windshield) on my MKIV Jetta won't stay on. When it falls off, the spring clip remains attached to the mounting base on the windshield. I have tried bending the spring clip outward (works until I hit a bump) and epoxying the spring clip when installing back in the mirror base (worked for a month or two).
I can't tell either from the diagram in the Bentley or from pictures of mirror bases that I found around the internet what precisely is supposed to retain the spring clip in the mirror base. I can get a used mirror base locally, but I'm just not quite sure whether the problem is with the base, the spring clip, or both...
Sonata I45 (YF - 2011+) :: Rear Tail Lights Falling Out
A week into owning my Sonata, I noticed the right tail light had become ajar, with the plastic fittings completely snapped off.
I had to take it to the dealership to get it serviced, whatever, problem solved. Right? Yesterday, the left tail light snapped off in the same way.
I have not been hit or gotten into any kind of accident for that matter. I got it serviced again today and asked if this was some kind of a defect in the car.
For both tail lights to snap off is really a mystery to me.
Ford F-150 (2009-2014) :: Rear Spring Spacers Removal
How to remove the spacer from the rear-end, spring and axle housing. If so, would it be the best to remove one at time etc. Must they be re-located below the axle or totally removed. I don't have a hoist to work from only floor jacks.
View 14 RepliesFord - Explorer :: 2002 - Driver Side Rear Spring Is Cracked
My uncle has a 2002 Explorer and the driver side rear spring is cracked. I have agreed to fix this as he is on a tight budget and has no mechanical skills or tools for that matter.
Anyhow, I did some reading and have two monroe quickstruts to replace the OEM stuff. I did not want to screw around with a spring compresser and everything else. Were in Michigan, and I can only imagine how rusted the bolts are on this. So I figured getting the whole unit with new hardware would be the best route.
Hopefully these are easy questions. (I do not have the truck to look at right now, and will be doing this Saturday Morning)
I have air tools, Jackstands, 2 floor jacks, a bottle jack, and everything else I need at this point including PB Blaster, rags, pry bars, sockets, etc.
1. I am assuming once I get the truck in the air, I will put the frame on jack stands, and use the floor jacks to manipulate each side of the rear suspension as needed. If I remove the three top bolts, and the bottom bolt holding the shock, can I move the control arm down enough to get the old parts out?
2. What are the torque specs if any for the top three bolts, and the bottom shock bolt? I read the top three bolts are difficult to get out due to limited clearance, so I doubt a torque wrench will fit in there.
3. Would you locktite these top three bolts at all?
4. Weakest question of the day, What are the torque specs for the lug nuts.
5. Anything I have obviously missed? I have done front struts before with a compressor so I am somewhat familiar with the process. Just not on this car before.
6. When Im in this far, anything else I should look at. I will inspect the brake pads etc. Drain and fill the rear diff fluid if needed, etc.
I have searched high and low on the net to find a pictorial write up of the process....
Ford Ranger / B-Series :: 2008 FX4 - Rear Leaf Spring Squeak
I've got an '08 FX4 that has developed quite a loud and annoying squeak from the rear leaf springs. It happens when I'm slowly applying power and going over bumps such as speed bumps or similar. More so when I'm going up hill.
I initially thought it was a u-joint going bad, and had my driveline mechanic take a look at it. He discovered it was the rear leafs making the noise. He sprayed them with an aerosol light grease and the noise was instantly gone. The problem is, the noise comes back after the grease spray has worn off (usually after driving in the rain) which happens a lot in the Vancouver area.
This is my 3rd Ranger and I have never had this problem. I don't drive in unusual places (beach, sandy, dusty areas) so I don't know why this is happening. It does look rusty in the areas that I can see in between the individual leafs. Is this a common problem for this vintage of Ranger?
Ford Excursion :: Spring Mod Update - Blocks In Rear Or Springs On Axle?
Finally pulling the trigger on some springs so I can get this work done, Tousely prices were great on the W's compared to local dealers. Here are some questions.
1. I am planning to go with the W springs up front.
2. Can I still use the B for the rear mod, or do I need C's to keep it level? (Or F's)
3. Do I need blocks in the rear, or just the springs on the axle?
4. Do I need the 2" shackle up front?
5. I have dual Fox shocks that came with the ex when I bought it. The prior owner said they ran a little rough. Are they able to be re-valved, or is it cheaper to go with Bilstein?
Ford Super Duty (1999-2016) :: Speed Nut For Rear Leaf Spring
Where I can get or have a speed nut for the front eye bolt of the right rear leaf spring? If you do I'll gladly send you some cash for it and to cover shipping it. It's supposed to rain pretty much all week here and I really don't want to go to a junkyard. I have checked ford parts and nothing there you can get the hanger that attaches to the frame that the spring bolts to but not the speed nut or bolt only need the speed nut though. Truck is an 2004 f-250 so 1999-04 will work and 05 to 07 is setup the same in the rear but I don't know if they are the same size bolt since they made the frame heavier. I have no idea after 07 when they made the springs longer.
View 1 RepliesFord F-150 (2009-2014) :: Rubber Burning Smell From Rear Wheels
I recently puchased a 2012 F-150 with the "ecoboost" engine. Recently I've been noticing an odor of what seems to be like rubber burning coming from the rear end of the truck.
It's very prominent when I stomp the gas pedal, with the traction control disabled especially. There's quite a bit of smoke coming from the rear, and the truck seems to over-accelerate for a V6. Should I take it to the dealer for repair?
Ford F-150 (2004-2008) :: 2007 - Removing Rubber Step Off Rear Bumper?
I have an 07 King Ranch. I need to remove the rubber step off the rear bumper to paint it. Due to a typical Ford paint job it is rusting already. Can I just pull up on it ? If so should I wait for a warm day to prevent breaking the clips?
View 3 RepliesGolf/GTI VII :: Spring Binding Popping Noise After Neuspeed Race Spring Install
This noise I have is driving me crazy, installed neuspeed race springs and now I have this weird spring noise, sounds like the springs are binding and then releasing when you turn the wheel, like a clicking dinging noise, it's on both sides and happens when moving slow and turning the wheel and when stationary and turning wheel, it sounds like tug and release not really spring bind I checked install and everything is correct even disassembled bearing assembly and everything is fine, lubed spring seats with silicone paste nothing is working.
When looking at the spring and turning wheel it's almost like the spring is getting stuck on the middle part of the seat then releasing, I know this was a common problem on the mk6 but I haven't heard anything about the mk7 the spring is seated in the lower perch perfectly the upper is were the noise is coming from you can see as you turn the upper bearing by hand it actually somewhat twists the spring and then releases and that's what makes the noise, and it dose not move in a nice circular motion kind of like an egg shaped rotation and it makes the spring flex and pop I think there's a problem with the springs,
Ford Excursion :: 2003 7.3L - Coolant Leaking From The Passenger Side Rear Hard Line By The Front Spring Hanger
On my 2003 Excursion 7.3L, I notticed I'm leaking what I think is coolant from the passenger side rear hard line by the front spring hanger. I haven't pealed the plastic loom away yet, but I did see the loom is chaffed near the spring hanger. What lines are the ones that carry coolant, and can I just cut the hard lines and replace with a section of rubber hose?
View 3 RepliesFord Aerostar :: Rear ABS Light Came On Suddenly
I was driving home tonight, in a thunderstorm in the middle of WINTER, when all of a sudden my Rear ABS light pops on. Me thinks a wire might be needing fixing, but what if it is something more sinister??? Is there a way to pull codes for the Rear ABS light??
View 14 RepliesCamry :: 2011 LE - Knocking In Rear After New Spring Installation
I need to figure out a knocking sound that I have coming from my rear struts. I installed new springs on my 2011LE 4cyl yesterday and now when I hit some bumps I get a knocking sound. I didn't cut down my factory bumpers so I think that might be the reason but I first wanted to get your option. The spring drop it's 1.5 on some Megen springs.
View 6 Replies