Ford F-150 - 1997-2003 :: AC / Clutch Bearing Making Noise - New Starter And Still Won't Start
I have a 2000 F150 XLT 5.4L truck. I noticed the AC went out about a month ago and since then I could hear the AC/Clutch bearing making noise. Well I went to start it the other day after eating dinner out and it wouldn't start. It sounds like it wants to start but it just doesn't have enough umph. I replaced the starter and charged the battery up to 100 percent. It still won't start.
If I take the belt off it will start and I checked the AC/Clutch and I can move it with my bear hands. I tried disconnecting the AC/Clutch fuse and relay but that didn't work. Is it possible that the Clutch is freezing up when I try to start it?
Ford F-150 - 1997-2003 :: Oil Light Is On / Gauge Dropped To Below L / Engine Started Making Noise
I drive a 2001 Ford F150 4.6L , Miles at 175,000+ (a little more but no more than 176k)
Situation as it happened : Driving home from work for lunch, about halfway home I notice that my Oil Light is on and the Gauge has dropped to below the "L." Engine started making noise, best I can compare it to is to the sound of a diesel engine when it's idle. Immediately pull over after noticing this, shut off engine for about 5 mins, check oil, oil is fine. Turn truck back on, light is off, gauge is normal, and noise isn't as loud as it was before. Drive rest of the way home no problem. After deciding on driving the truck back to work (I know i shouldn't have but I have no other means of transportation, and I work at Autozone so I wanted one of my managers there to check it out) I turn on engine, everything is fine, no oil light, gauge is in the middle of the "H" and "L", only thing wrong was the engine noise, except like earlier it wasn't too loud or shaking the truck. About halfway to work, I come to a stop sign, Oil gauge shoots down below the "L" and the oil light come on.
As soon as that happens engine starts making same loud noise as before (diesel truck idling.) I push the gas to get past the stop sign, and instantly truck loses power in pedal and just shuts off. Make it to side of road, hasn't turned on since. Never had any problems with the truck since I bought it 5 months ago, changed the oil 1 time about 2 months after I bought it. I'm just hoping my engine hasn't seized up on me.
Not sure if this matters, but about 4 days prior to this, truck was making a rattling noise, almost like shaking a can of paint , under the front drivers side, in the suspension. Was told those were probably due to my sway bar link bushings being busted.
After some research on here and other websites as well, I have come to find out that this is pretty common in most Fords? Most people recommend changing the oil pressure switch, and others say it could be the oil pump? Was planning on changing out Oil Pressure Switch, and changing the oil filter/oil , and fuel filter as well. Not sure what else I could do?
Ford F-150 - 1997-2003 :: Passenger Side Brake Started Making A Grinding Noise
I have a 1997 F150 (truck in signature). In December my passenger side parking brake cable broke so I replaced both rear cables (front cable appears in good condition).
This past Friday the passenger side brake started making a grinding noise so I pulled the drum to find the self adjuster cable broken and the ratchet jammed between the shoe and the drum. I pulled everything apart and put new shoes (the pin the ratchet pivots on was broken off the rear shoe)and all new adjusting hardware (adjuster screw, ratchet, cable, and cable guide). The rest of the hardware looks in good condition (still paint on the springs and retainers). I got everything put together and took it for a test drive, it had a nice firm brake pedal (it's been a while since this truck has had a firm pedal) and great stopping power.
Took it to work today, and on the way back I stopped to pickup a package from the UPS store. I set the parking brake and put the truck in 1st like I always do. When I got back out to the truck to drive home, I released the parking brake but there was still obvious drag as I drove home (no good place to stop during rush hour), got out of the truck and it reeks of burning brakes. I pulled the driver side drum off (after it cooled), which was rather difficult, and everything looks to be in order except the rear shoe was not touching the post at the top of the backing plate. I checked and the adjuster was still all the way in, so that isn't the issue.
I pulled the parking brake cable out to slack the drum side of it (with the pedal released there is some spring tension from the pedal mechanism) and clamped it with vice grips so the cable was slacked and the shoes were then touching the post, and the drum could be installed and turned relatively easily, I then removed the vice grips and let the spring pull the tension out of the cable and the brake held firmly (requiring considerable effort to turn the drum). Is there anyway to adjust the spring tension on the parking brake cable when the parking brake is released?
Additional notes: when setting the parking brake, the pedal will only go down an inch or 2 before the brakes are locked up tight and the pedal won't move, it used to go down several inches before. also I noticed that the feral on the end of the drivers side cable (that locks into the lever attached to the rear shoe) is deformed, like the cable has too much tension on it. The cables are the correct ones for my wheel base according to Autozone but I'm starting to wonder if they are too short. Spring tension on the parking brake cable (when the brake is not set) causes the parking brake to drag. How do I get the parking brake to stop dragging? ("star" adjusters are new and adjusted all the way in).
Subaru - Forester :: 2003 - Transfer Clutch Assembly Making Noise
I have a 10 year old 2003 Subaru Forester in "very good" condition....except that the transfer clutch assembly is starting to make noise and the repair shop (at the dealer) says, housing has to be replaced also. The car has 130K miles and has had all its regular maintenance for 10 years. The only major mechanical problem we've had are the head gaskets (which on this year's model were NOT part of the recall). Those were fixed 2 years ago. Some of what I see in the online chatter about transfer clutches suggests that this is a slippery slope and the next thing you know there's the "next thing" that needs to be worked on. We were hoping that the 2014 Forester would get really good mileage (this one got 30 when it was younger) but we hear it will only be 32 mpg so we're inclined to "keep waiting" if this car can be kept happy. Is a transfer clutch repair a big deal?
View 7 RepliesFord F-150 - 1997-2003 :: Truck Started Making Screeching Noise When Turn The Wheel And Moving At Slow Speeds
97 F150 4x4 around 200k miles on it, Drove the truck to town today and it started making a screeching noise when I turn the wheel and moving at slow speed's It is not the typical Ball joint squeak, and they were replaced about 6 months ago. I also get a clicking squeak going down the road, everyone in a while from take of ill get a slide grinding or crunching noise. Also noticed that when taking a curve to the right i feel and hear a slight Bump but I don't when turning to the left/
Also it doesn't have the typical grinding noise of a bad unit bearing, there is a slight roar but Pretty sure that it is just the aggressive tire's... I am about to go out and Jack it up and have a look at it to see what it was. Also if I loosen the Cv nut on at the Hub that would show me if there was any play in the bearing correct? since the cv should keep the bearing's fairly tight even if they are worn?
Golf IV / Jetta IV :: 2003 - While Shifting Making Grinding Noise - Clutch Or Engine?
noticing a few issues with my 2003 jetta 2.0 when driving/shifting....so first main thing I noticed is when shifting from 1st to 2nd gear often times it will make a grinding sound and not shift smoothly from 1st to 2nd....you have to do it real slow/gingerly ...if I short shift from neutral to 2nd its fine or if down shifting to 2nd its fine...I have changed the gear oil...other sounds idk if its my tranny or engine but if going up hill and you throw into 3rd and not going fast enough its makes a rattling sound and is sluggish I know its a old car 177,000 miles so idk just curious if this is a sign of problems?....Last thing after driving and getting home and putting into reverse gear to park it makes a noise like a chugging sound when reversing and can be finicky going into reverse.
View 1 RepliesFord Excursion :: Fan Clutch Making Noise?
I've had a jangling fan clutch for awhile. Would love to get ridbof this. Any tricks to get rid of that noise? Pretty sure its functional, just noisy.
View 10 RepliesFord A/C :: 1996 F350 - Clutch Making A Lot Of Noise
I just got done changing a/c clutch on a 96 f-350 5.8 because it was making a lot of noise. The new one is just as bad. Would the air gap cause this? When I took it off I could see it was hitting the pulley. The gap was 0.21 is that the specs on it.
View 3 RepliesFord A/C :: Compressor Clutch Making Noise / Would Engage Or Disengage
The A/C in my truck stopped working last year, and this year I intend to fix it. I believe the problem is with the compressor clutch because it was making noise as it would engage or disengage. It was making this noise for a good year or so, and then one day the noise stopped and I have no A/C. So I am only assuming its the clutch.
View 4 RepliesFord - Focus :: 2005 - Started Making Noise Like Motorcycle Coming From Behind?
Several weeks ago my car started making a noise that sounded like a motorcycle was coming up behind me. The noise started in at 65 mph and now, weeks later, starts in at around 35 mph. I have had the muffler checked and the CV joints and everything checks out okay. The noise does not change if the car is turning left or right. The noise is also, curiously, no louder with the windows open or closed.
View 4 RepliesFord - Explorer :: 2010 - Compressor Started Making A Grinding Noise When Turn The Defrost On
My wife has a 2010 Explorer 4.0 with 46000 miles on it. Yesterday the compressor started making a grinding noise when you turn the defrost on. It's only when the clutch kicks in. I'm hoping its something simple but, I fear its not.
View 8 RepliesFord F-150 (2009-2014) :: 2012 - Engine Started Making A Chirping Noise When Accelerate
I have a 2012 3.5 eco boost. It has 82,000 miles. I just purchased a large travel trailer. That is the first thing I have ever towed. When I was accelerating onto the interstate the engine started making a chirping noise.( not the normal turbo whistle). It went away when the rpms came down, and now every time I accelerate, it makes the same noise around 2000-2500 under load.
View 6 RepliesGolf VI R :: Clutch Noise Making Vibrations?
Searched through old threads but didn't come across these in particular, a lot to look through so may have missed in Car has 270 miles on it.
1) When clutch is in all the way and the car is revved, I can feel it in my left foot. This can be felt when car is stationary or in motion - Is this common for MK6/R? I don't recall being able to feel this in my MKV GTI
2) When the car is in motion, I hear a knock noise right after the clutch is pressed in. I can only hear the noise if windows are open and stereo is off, and this only occurs while the car is in motion. - Is this a standard clutch noise for healthy clutch/pp/flywheel/throw-out bearing on this platform, or should there be no noises? It sounds like something I'd expect to hear with a messed up throw-out bearing.
Ford 6.7L Power Stroke Diesel :: Fuel Filter / Pump Started Squealing And Making Vibrating Noise
Well, I last summer my fuel filter/ pump started squealing, and making vibrating noise, replaced the fuel filter changed the noise slightly, some times it would go away, sometimes the line going to the filter under the hood would vibrate, couple weeks ago truck warning light came on- "low fuel pressure warning" came on, hum... went out, came on a couple days later, then finally put me into limp mode, luckly only 1/2 mile from home... checked filter on frame/ tightness, it was tight, the pump on the filter housing was very noisey still, well, I figured 200 dollars cheaper than taking to ford....
I waited and pump arrived 3 days later, replaced it and low pressure warning still on, but pump was very quiet, and when I restarted low pressure warning and reduced power came on in driveway, hum.... I thought code was still in computer, I disconnected battery and turned headlights on to try and kill the code, started it and now the engine light came on, nothing else, and truck ran fine....hum.... went to autozone, and they pulled the code, low fuel rail pressure, p0087, guy said to drive and code should go off, truck runs fine. Drove truck a couple days and engine light went off, Truck runs great.......All is good.
Lexus GX 2004-09 :: AC Clutch Shot - Making Grinding Noise
My 04 GX has about 113k on it and the A/C clutch is shot, making a ton of grinding noise when its engaged (when the A/C is on).
Need to repair or replace there unit because of this? I see online the ability to buy just the clutch pack for the A/C compressor. However Lexus and other sites want to sell me the whole A/C compressor.
Question being, can I get away with buying the clutch pack and installing it onto my OEM a/c compressor? Or do I buy a new compressor?
Golf VI R :: 2013 - Clutch Making Noise Whenever Changing Gear At Low RPM
I have a 2013 golf r and I usually shift gear at 3 rpm when driving normal but for some reason it doesn't feel right, I can hear the clutch making a weird noise whenever changing gear at a low rpm, it feels so much smoother when shifting above 4 rpm but I dont always wanna punch it so hard especially when there's always traffic from where I live. Any advice on a smoother shift at a low rpm.
View 22 RepliesCaprice :: A/C Compressor Clutch Making Lots Of Noise When Working
Pretty sure the a/c clutch on my LT1 is going - making lots of noise when working and also when not.
I've heard on some forums that this could be a bearing? Is it advisable for me to replace the entire clutch or just this bearing?
Either way, I assume I'll have to pull the clutch for which I think I'll need two special tools:
(1) clutch holder tool to break nut loose.
(2) pulley puller.
Subaru - Legacy :: 1999 - Clutch Seems To Be Slipping, Making Some Noise In 3rd And 5th
The car has about 142,000 miles. Is the clutch on this car adjustable? My repair files indicate it was "adjusted" a couple times, $40 each time. Now I think I might need a new one: it seems to be slipping, making some noise in 3rd, and in 5th.
View 2 RepliesChevrolet - Camaro :: 1987 - Clutch Making Rotary Grinding Noise
I have a 1987 Camaro with a 305 TPI V-8, with a 5-speed manual transmission. I rebuilt the transmission, and installed a new clutch, pressure plate, throw out bearing, and had the fly wheel ground (which the machine shop said that it took very little material off to get clean-up). When we first got the car running when the car is moving in any gear (even in neutral) with the clutch peddle down, I get a rotary grinding noise (but only about 30% of the time). If I let the clutch pedal up the noise stops immedately. The transmission shift smooly, in all gear selection. I thought that I had gotten a bad throw out bearing, so we installed an other new throw out bearing, but I get the same noise. Is there something that could cause this noise inside the transmission?
View 8 Replies