Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Auto Transmission Code / OD OFF Light Started Flashing
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To Reverse Light Sockets
I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Airbag Light Is Staying On / Code 25
Just bought a 2002 F-250 4x4 Off-Road Crew Cab 7.3L and the airbag light is staying on. I have found out after the fact that the truck has been previously involved in a front end collision. The damage was to the passenger side front. I turn the ignition on, the airbag light will come on solid (just like all the rest, with the exception of the 4x4 and 4x4 low) then go out. Then it flashes slowly 2x then 5x, then goes out for a bit then repeats a few times before staying on. This tells me I am getting a code of 25. I have searched with no luck to narrow this issue down. Everything mechanically works, cruise, horn, etc. The only thing I can find wrong is when I engage the 4-wheel drive (floor shifter) the indicator lights do not illuminate in the instrument cluster. Neither the 4x4 nor the 4x4 low. I am unfamiliar with this truck, so I don't know where to began searching. I cant afford to take it to a dealer and I have children in the truck quite often, so I would like to remedy this very quickly.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Door Ajar Light Is Lit Up On The Dash
I have a 2002 f250 screw. my door ajar light is lit up on the dash. I have tried the wd40 trick, pulled the sensors and bench tested them. What are the codes the instrument cluster test has for each door?
What I am thinking is, if we get a list posted it would be much easier to diagnose the door sensors for others. there should be a open/closed bit for each door. possibly a code for all doors open too. I am curious if there is a code for bad communication on the VSM.
From what I have read, correctly working the doors should read 00 when they are closed. drivers front open=80, pass front open=40 ... My door code does not change no matter what combination of door open/close I use.
Truck is 2002 f250 crew cab ...
My code is C0 ...
Ford 7.3L Power Stroke (1999-2003) :: Tranny Slipping And Not Up Shifting Then O/D Started Flashing
I spoke with a few people here before about my 4r100.. it threw a code a month ago for P0750.. i replaced solenoid and it continued to do it even after clearing codes numerous times.. then all of a sudden it was perfectly fine for over a week, no codes, i ran a few brick hauls with it and ran it for over an hour straight.. i went to fl and upon return i took her for a drive and wouldnt you know, the code has returned.. i did hammer down a little but not from a dig, i just got on it a little playing with a neighbor and his truck and all of a sudden it did its thing slipping and not up shifting then the O/D started flashing again... i cant understand why the code would come back all of a sudden, there has to be a wiring problem correct?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Panic Alarm Horn Sounding / Dome Light On
I own the above described vehicle; I'm at about 196k and I'm the original owner. It's a quad cab, 2002 7.3L with power everything. I believe it's the XLT package (it's not in front of me... I'm at work. CONFIRMED... XLT package).
Currently, it's the workhorse and back-up for the family, not my primary driver - luckily. I've had failure if the automatic door lock on the rear pass. door, and a sticky lock on the rear driver's side lock - they've both been in this state for at least the last four years, no problems beyond the hassle of manual manipulation of the door lock from the inside - otherwise no electrical issues really to speak of.
Three weeks ago, we went to the snow. I rarely use the 4x4, but found that I had to use it that day to get out of some mud - it worked fine, no issues. In addition, I also used the cruise control... something I do rarely, but have not had any issue with it either.
In exiting the area some hours later at the end of our day, I noted two things... the "door ajar" dash light was illuminated and did not shut off through the drive home, and the dome light remained on until the battery saver shutdown shut it down... quite some time (where normally a key in the column turned past the insertion would shut it off).
When I drove home I used the cruise control, as mentioned, and it worked fine.
In exiting the vehicle while at home, as soon as the door was opened the horn started blaring panic alarm style - honk, honk, honk, honk... - and when the batteries are attached, there is nothing that stops the honking, except the battery saver timeout. BTW... no key in the ignition.
I don't use the FOBs... the batteries were dead anyhow (and I moved the FOBs out of range of the vehicle).
Attempted fixes:
- Lubing the lock/WD-40, then shutting/opening the doors (no luck/no change).
- Pulling door panels, removing locking mechanism, removing door ajar switches (I don't know what they're called), manually manipulating the piston AND checking each with a multimeter. (NOTE: One "seemed" not to work properly, so I purchased one from dealer and placed it back... still, no luck resolving the issues overall).
-Checked the wiring looms supplying all four doors - no broken wires noted.
- Replaced the two vehicle batteries.
I'm at a loss and I'm hitting up this forum before I move forward...
I've read that there are issues with the VSM for this year's model, but I'm hesitant to purchase the module without further feedback from a tech. I've read some general posts about alarm systems (doesn't apply to me) and horn issues (but those were horn constantly blaring... not the intermittent horn blasts of a "panic alarm sounding."
I've heard that the GEM and clockspring could be an issue, but I have to look more closely at the associated problems (like recheck to see if the cruise works... door windows go up/down like some threads have mentioned...). I have also read that the door ajar sensor switches attached to the automatic locks could be culprit, as they may "work" when pulled out, but not work when they're installed in the vehicle.
Ultimately, what the cause to the panic horn beeping, dome light and door ajar instrument indicator being on.
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Tow / Haul Light Started Flashing - Code P0730 Incorrect Gear Ratio
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - P0781 Code / OD Button Flashing
So here it is, I have a 2002 F 250 CCSB, 7.3, 180k, 4R100 Auto (Build date 06/02 so no mechanical diode correct?), 4x4, 4 inch exhaust, Riffraff 6637 Blue filter, with edge evolution (run in STOCK ONLY, just using it for gauges) that has recently thrown the P0781 code, and flashing the OD button. The interesting thing is I haven't noticed any hard shifts from 1-2 or any gear change for that matter. Fluid was changed less than 2k miles ago, was nice and red.
I have read of others having to rev up to 2500 RPM and then let off of the throttle to shift. No such issues here. Drives the same as usual. The only issues I can think of would be a sticky shift solenoid, sticky shift valve, or intermediate one way clutch that can cause this problem, but as it is only a code and blinking OD light and no actual shifting problems I am at a loss?
Ford F-150 - 1997-2003 :: 2002 - Brake Light Started Flashing After Start Up?
The brake lights on my '02 F150 have started flashing spontaneously ie - with no one in truck. This lasts for a few minutes, then stops, but can start again a few minutes later. The fear of course is that someday lights could come on and stay on, resulting in dead battery.
I do have a trailer brake controller that has been on truck ten years. Read something on internet that brake pedal switch might be going bad (??). Any one else observed this strange behavior?
Ford 7.3L Power Stroke (1999-2003) :: Airbag Light Flashing - No SES Light Or Fault Codes
Came on other day. No ses light or fault codes. What it means?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Overdrive Light Flashing Sometimes
The overdrive light is flashing but not all the time. What does this mean?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To PCM Fuse
I just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power Getting To Fuel Pump
There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Accessories Come On
My 02 F250 periodically has no acccesories like electric windows, radio, and AC do not work for a minute or so. It has been doing this for awhile and seems to be getting more frequent and I am concerned that it might go out on a trip. It runs OK when this is going on and usually happens on the first start on the day. I was thinking maybe the ignition switch?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Cranks But Won't Run?
2002 Ford F250 super duty 7.3L Diesel Automatic I crank but wont start and run.
Background:
I live in NY, last winter (2013-2014) fuel pump stopped working, I discovered this website, changed my fuel pump although mine worked fine after I did it, Power was not going to my fuel pump, took apart truck to follow wires to find the problem, wires come from the fuel pump into the CPU and Fuse box, relay is built in fuse box, changed fuse box, truck started, from early spring to summer ran without problems, in summer friend ran truck dry without filling up luckily he threw it in neutral and shut off engine rolled it to a stop, Filled up truck after a few tries it starts up. A week later the fuel filter o-ring rips and spews diesel all over engine, changed filter ran for a week and o-ring poped out again, changed to a different o-ring and ran for a month without problems. Then poped again, and again, each time approximately a week later.
Latest winter (2014-2015)
I start my truck to warm up go inside and forgot all about it, about 1.5 hours later I remember my truck is started, go outside to find it shut off with diesel all over the pavement, the o-ring blew again. I changed it, cranked the engine and it started and ran for 10 seconds before stalling. I turned the key a few times to try and have my fuel pump run, and it would crank but not start. Then it started to crank really slow,(batteries were now already on charge) it was below freezing for a good whole week now, found my oil heating plug and waited a day, cranked it the next day, cranked faster but did not start, waited another day and when I tried to start it the starter would not turn.
Today:
So today, winter is almost over(if you lived here you would understand) I find out I blew my starter and changed it, I replaced the o-ring with [ 90025K557Double-Seal X-Profile O-Ring, Oil-Resistant Buna-N, Dash Number 347 ] from Mcmaster.com as suggested on this site. I cranked the engine, It started ran for 30 seconds and stalled. I tried turning the key a couple of times to get fuel going(fuel pump seems to be working), but crank and wont run. My father suggested starter fluid, got couple cans, I was able to start the truck with starter fluid and keep it running until the can ran out.
It wont start and run on its own like it did the first time I tried.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - CEL Came On For 30 Seconds And Went Off
I have a 2002 F250 7.3 with 130,000 miles. The truck was bought new by my father and is completely stock and never run hard. I was driving on the interstate at 70 mph and the cel came on for 30 seconds and went off. Not long after it went off the truck shut off and has not started back. That was around 12-20-16. I have put a new cps, icp, and ipr on it with no luck. All ford parts. I drained the fuel water separator to check the fuel pump and it filled back up. The truck is turning over good but has no white smoke witch leads me to think maybe the IDM. I'm a novice to all of this and until this happened new nothing about any of these parts but I'm learning. I do have the torque app if I should check some things.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Started Running Bad Mid Drive / White Smoke With Diesel Smell
Just happened today right after I bought diesel. thought it may be water in fuel but after researching wondering if it is injector, etc. It starts every time knocks real bad sometimes for a minute, but clears up to idle ok. During idle no smoke, slightest acceleration however produces white smoke harder I accelerate more it plumes and it smells like diesel in the air.
Cannot get past 15 or so mph till switching into 2nd gear then 25mph max. Had to drive 4 miles like this I can say it cleared up and drove 1/2 mile until I had to stop at a traffic light then going from idle to acceleration again ran bad rest of way home another 2 miles.
A few years ago I did have a rough idle and accel. similar and it ended up being the broke pick-up/sending unit in tank (but of course that was when you get to around 1/4 tank of fuel and didn't run bad above that much fuel in tank), plus there was almost or more than a gallon of water in tank. I have done the mod for the fuel pickup with hoses, filter canister, etc. but wondered at first today if I had gotten bad gas or water in the tank again. Not sure how that much water got in the tank to begin with but that was bout 5 or 6 years ago.
Truck has over 200k miles and Ive had it for 11 years. In the morning will check the ICP sensor by unplugging look at fuel filter bowl, etc. A question I have is: Is water heavier than diesel, would it run thru my line first? thinking diesel is heavier than gas because of oil content....
Ford 7.3L Power Stroke (1999-2003) :: Overdrive Light Flashing - TSS Not Detected
My F350, 7.3 L. is flashing the overdrive light. Had a pro do a scan that said no Turbine speed sensor signal.
I would like to know where the TSS is located and then see if it has corrosion other reason not to connect.
Ford 7.3L Power Stroke (1999-2003) :: Flashing OD Light - Code P0741
I am trying to make sense of a P0741 code accompanied by a flashing OD light.
The truck is a 2002 (12/01) build date) F250, 7.3,4x4, Auto, with 245,000 miles on it. The truck seems to shift fine but around 40/45 it feels like the TC does not lock, followed by the flashing OD light.
The transmission was serviced 500 miles ago but the OD light flash was intermittent until last week, now its been constant. I want to take care of it before I do any damage.