Ford 6.0L Power Stroke Diesel :: Intermittently Running Rough At Idle - Code P0269
So my truck is intermittently running rough at idle for the most part and sometimes slightly loses a little power while driving down the roads. Seems to run worse as it warms up. When it runs rough it sounds like a cylinder is missing. The truck is throwing code P0269 for Cylinder 3 Contribution/Balance. Smoking isn't horrible coming out of exhaust but it's there and it comes out at a constant rate. The injector has been replaced by the previous owner recently. It has an egr delete, new turbo, ficm, ficm harness, HPOP, and stand pipes.
When I put the starter solenoid wire to the battery you can hear the engine skip. I did a compression test on cylinder 3, put oil in the cylinder and did the test again to find that I still didn't have compression. Assuming that this was an issue in the head I had my doubts that it was a bent valve and it could have been a bent pushrod.
Sure enough I found the intake pushrod for cylinder 3 was bent slightly so I replaced the pushrod. I started the truck again and seemed fine at first but just like before it started to run worse as it warmed up.
I was able to drive it to the gas station real quick to fill it up on fuel and drove back home which is a short drive, but the truck was running worse and worse and it eventually died on me. I attempted to start and had to jump start from my other truck and the 6.0 would not start. I ended up frying the starter trying to start it so I'm taking a break from it for now.... Ended up pushing the truck home.
The only thing I can figure is that I don't have oil pressure in the oil rail which is why it died but I don't understand why the truck still ran rough and pulled up with the same P0269 code....
Ford 7.3L Power Stroke (1999-2003) :: Shaking While Accelerating Between 45 And 60 Mph And Rough Idle - P0284 Code
I got a p0284 code and have some symptoms such as shaking while accelerating between 45 and 60 mph and a rough idle.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - Rough Idle / Cylinder 4 And 5 Contribution Balance Code
2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.
Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.
So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.
Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?
Ford - Explorer :: 2003 - Misfire On Cylinder 8 / Running Rough At Idle And Under Load
126000kms on 03 explorer 4.6 truck started. Running rough at idle and under load.... Code came up for cyl 8 injector. Replaced injector... problem still there. Switched cop and plug with another cyl and plug.... same code and cycl 8 is definitely not working. Would a generic problem always affect i cylinder. I even checked wire clip on for injector... it appears ok. There is power to injector wire clip.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Bad Cylinder - Smoking And Low Compression
I got a deal on a1997 f450 7.3 what does it take to swap to 2001 f250 7.3.mine has a bad cylinder with smoking nd low compression.
View 5 RepliesFord Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Removing Brake Master Cylinder?
I tried to replace my brake master cylinder today but wasn't able to because of a plug
It's the black plug on the drivers side, the connector is upside down so I can't see how to unplug it I tried for an hour then got too frustrated I had to come inside
My Haynes manual says "unplug" obviously
Ford 7.3L Power Stroke (1999-2003) :: Ignition Lock Cylinder Removal With No Key
So I have a replacement steering column for my truck and need to swap out lock cylinders. My question is; since there is NO key, is there any way to avoid drilling out retaining pin. If I did drill it out am I entirely screwed'?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Doing Clutch - Slave Cylinder Removal
I'm getting ready to swap my clutch and got to looking at the slave cylinder. I read somewhere that you have to rotate and twist it to get it out? Or something else? Also after reinstalling how do you get the slave plastic piece cut that holds the rod in? Or do you just push the clutch?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: P1273 Code - Cylinder 3 High Low Open
So I got an IDM code and then after running AE buzz test got a P1273 (#3 cylinder high low open).
Ohm'd out the 42 Pin - got 3 across the board. Only test 42 pin from valve cover to injectors.
Double checked UVHC
Swapped solenionds
Swapped injectors
Did ford wiggle test.
Ran Injector buzz between all those steps and still get P1273.
What's the next step? Ohm from IDM to 42pin? May actually be a bad IDM?
Ford 7.3L Power Stroke (1999-2003) :: HPOP Hose Leak At Cylinder Head
I have an oil leak where the HPOP hose attaches to the cylinder head. I have the removal tool for the hose. I assume I need a new fitting. What's the torque spec for this fitting, and any additional tips I need for doing this repair?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Check Engine Light On / Cylinder 5 Misfire
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Cylinder Missing Until Motor Warms Up
My feed truck (2001 ext cab 4x4 7.3 198k) had a cold starting issue I fixed with new gp relay. Now I noticed when it gets down below 30 degrees it has a cylinder miss until motor warms up. I don't doubt injectors are in my future. I was wondering though if that is common for worn injectors or if maybe something else has gone haywire and how long can I run it like that before something else tears up? after about 7-10 min the miss goes away and I don't notice it. I would like to get through the winter before messing with it or having injectors put in it...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Washer Fluid Hose Dropped In Cylinder
Like the title says I dropped about a 2 inch piece of small washer fluid hose in my cylinder while evacuating the oil from it . Will it damage the valves If I ran it? Any way to remove it without removing the head?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Replacing Clutch Master Cylinder
I am looking for a how to vid or resource on doing the job right. I purchased the complete replacement master cylinder from Napa. 2002 7.3 Powerstroke
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: P12777 - Cylinder 7 High To Low Side Fault
So the other day I was driving my truck and all of the sudden it through a p1316 code. So I did a Buzz test with FORscan and it gave me this error P12777. For the people that have dealt with this code before, where should I start looking, As I have a lot of stuff to take out on the passenger side before I can even see the valve cover. Is it more of a wiring issues or is it a injector issue.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Smoking When Rev The Engine And Imbalance On No 1 Cylinder
I have a 2000 7.3L f250 superduty. after rebuild and a yr now have engine smokes when you rev the engine and an imbalance on No1 cylinder causing injector to carbon up poss from prev misfires due to injector harness now solved? Found the turbo exhaust outlet pipe leaking oil we think because the wrong size clamp fitted. will fit new clamp tomorrow but if this does not solve problem what next? This has now cost thousands and still having problems...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Cylinder Head Fuel And Oil Rail Plug ORing Replacement
Is this job worth doing as a preventative maintenance item? I replaced the rear fuel rail plug (aka banjo bolt) o-rings because they were very easy to get to with the up-pipes out. But the cylinder head plug in the rear is pretty high up and even with the up-pipes out, there isn't enough room to get a breaker in there that's long enough and has enough movement to loosen it. The front would be easier to get to, but both accessory brackets need to come off to get to them on both sides.
As far as I know, none of them leak but they're all 17 years old... BTW in case you haven't been following, I'm doing up-pipes, injectors, turbo, rebuilt HPOP & fuel bowl, boots & clamps, etc. so I'm trying to knock out any PM items while I have it apart.