Ford 7.3L Power Stroke (1999-2003) :: 1271 Injector Code - High Side To Low Side Open Cylinder 1
I've got a 1271 code and I can't seem to make it go away. Code definition is "High side to Low side open Cyl 1". The truck runs fine, no rough idle, no excessive smoke of any color, just the damn CEL light stays on. I check the UVCH and all the injectors ohm in at 2.7 ohms. I've already done the updated clips under the covers. I run all the buzz tests and KOEO/ KOER tests and all appears OK. My AE won't do a Cyl contribution test. All the injector data shows all 0.00. I know its not that perfect. "high to low open", does that mean I've lost a ground? If so where?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: IDM Failure Code And High Side Open Bank 1 And 2
Today I just installed a brand new IDM and after running the Injector Buzz Test test, I received codes: P1298 Injector Drive Module Failure, P1293 Injector High Side Open - Bank 1, and P1294 Injector High Side Open - Bank 2. How a new IDM could throw these codes?
When running the KOEO test I received codes P0605 Injector Control Module Read Only Memory (ROM) Error, P1298, P1293, & P1294.
My engine is still missing but the engine is running a heck of a lot better after replacing the IDM and injector 8 has a rotational velocity of about 3%
Ford 7.3L Power Stroke (1999-2003) :: Code P1271 - #1 Injector High - Low Side Open
Getting DTC Code P1271 - #1 Injector High -> Low Side Open.
The code tends to show up more during cold weather start up. Using AE-AutoEngenuity KOEO - Buzz Test returns the P1271 error
Troubleshooting performed:
- 42-Pin Connector @ Driver Side Valve Cover
- 9-pin VCH on Passenger side
- IDM Module under driver side wheel well
- All of these are testing within the 2.8 - 3.2 Ohm range
- (Used the GB Reman. Tech Bulletin 103) - TB 103: 1994-03 Ford 7.3L IDM Replacement & Diagnostics)
I was going to replace the solenoid, however, with the above readings I'm not convinced it's the solenoid. Before I tear into the valve covers I was looking for some add'l thoughts from the forum. Could it be the IDM ?....
Any add'l checks to perform using AE, or the IDM, other than replacing IDM.
01 Platinum 7.3 - BTS - PHP Hydra Tunes - 4" FloPro - Riff RaffWheel - Redhead Steering - Driven Diesel Hutch/Harpoon - Kenwood DVD w/ back up- 35"s - GloPro EGT/Pyro/Boost/Trans, Scan Gauge II, AE bundle
Ford 7.3L Power Stroke (1999-2003) :: P12777 - Cylinder 7 High To Low Side Fault
So the other day I was driving my truck and all of the sudden it through a p1316 code. So I did a Buzz test with FORscan and it gave me this error P12777. For the people that have dealt with this code before, where should I start looking, As I have a lot of stuff to take out on the passenger side before I can even see the valve cover. Is it more of a wiring issues or is it a injector issue.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: High ICP - Code P1211
I had a p1211 code when I first got Torque Pro hooked up. I figured it was just because I'd done a couple WOT runs and the HPOP just can't quite keep up with the injectors. I was told this might happen when I ordered the injectors from Gear head. I also noticed that my ICP peaked at around 3600 during one of these runs. I don't have it logged, but I'm certain it was up that high.
The code hasn't returned, but I haven't been running it too hard either. I don't quite know what to make of the ICPs actually being that high. From looking at a bunch of Rich's graphs his doesn't really get past 2800 or 2900. Is this an incorrect reading? Do I need to worry about anything?
Ford 7.3L Power Stroke (1999-2003) :: Fuel Relief Valve Is Stuck Open - Code P1316?
If the fuel relief valve is stuck open would it possibly throw a P1316 code?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Code P0262 - Cylinder 1 Injector Circuit High
Have a 2004 F350 which had problems starting cold and once started had bad throttle response until warm. It also had a shudder at cruising speed when going up a slight incline, would shudder until turbo kicked in.
Pulled codes which related to FICM and codes for all 8 injectors. 7 injector codes were circuit low, cylinder 1 high. Tested FICM voltage and sent FICM out for repair.
Installed rebuilt FICM, cleared codes, and hard start went away, but cruising shudder is still present.
Only existing code is P0262 for cylinder 1 injector circuit high. I'm assuming that cylinder 1 injector is bad -- are there any tests to confirm before I take it apart to replace it?
Ford 6.0L Power Stroke Diesel :: Engine Missing - Code P2077 - Cylinder 6 Injector Circuit High
I have for a week suspected my batteries were getting weak. just slower cranking is all. I took my truck in to have a viper security system installed and while he was doing his work he killed the batteries. I saw him hook up a battery charger and started the truck. He pulled it around to me and explained how the system worked and off i went. 5 miles down the road, on the thruway, I notice a miss and I'm down on power. FICM looked ok, 48V and it was charging, 13.8 I thought I would bring it to my shop and load test the batteries. On my way here, the check engine light comes on. At the shop, load tested them and they were weak. Installed 2 brand new batteries, started it up, no difference. Hooked up the scanner and pulled a code P2077 (cylinder 6 injector circuit high) Now what? I'm not sure where to go from here. I'm guessing either the FICM went bad or the #6 injector?
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: P0269 Cylinder 4 / P0284 Cylinder 8 Running A Little Rough
So I did a cylinder contribution test and a buzz test today. It buzzed evenly on all cylinders. Then when I did the cylinder contribution test I got these codes,
P0269 cylinder 4 contribution balance
P0284 cylinder 8 contribution balance
It has been running a little rough lately but not smoking. Seems to be chattering more than it was too. I did the FRx, HPx, CVDs and banjo bolt mods about 500 miles ago and it was a lot quieter and ran better. Just recently started running rough and a little louder. Could these injectors be bad? I did new injector O-rings about 800 miles ago. I ran the test with the engine cold and with it warmed up and got the codes both times. It seems to have a little bit of throttle flutter when holding it about half throttle while driving.
As far as I know the injectors haven't been replaced and they have 186K miles on them.
2001 F-350 Lariat Dually Supercab 6-spd manual 7.3 Powerstroke Turbo Diesel 186,000 miles....
Ford 7.3L Power Stroke (1999-2003) :: Code B1230 - Driver Safety Belt Retractor Low Or High Resistance On Squib
So I am trying to learn how to use the forscan program. I find that it detected an open circut for th deleted intake heater, which I expected. It also found :
===ECS DTC B1230===
Code: B1230 - Driver Safety belt Retractor Low or High Resistance on Squib
Module: Electronic Crash Sensor
Diagnostic Trouble Code details
Driver Safety belt Retractor Low or High Resistance on Squib
So that answers the the question about the intermittent airbag/ seat-belt lamp. How to solve this problem? BTW- This is a E350 SD Van ....
Ford 6.0L Power Stroke Diesel :: 2003 - Cylinder 5 Misfire Code P2285
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Rough Idle / Cylinder 4 And 5 Contribution Balance Code
2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.
Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.
So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.
Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?
Ford 7.3L Power Stroke (1999-2003) :: Bad Cylinder - Smoking And Low Compression
I got a deal on a1997 f450 7.3 what does it take to swap to 2001 f250 7.3.mine has a bad cylinder with smoking nd low compression.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Removing Brake Master Cylinder?
I tried to replace my brake master cylinder today but wasn't able to because of a plug
It's the black plug on the drivers side, the connector is upside down so I can't see how to unplug it I tried for an hour then got too frustrated I had to come inside
My Haynes manual says "unplug" obviously
Ford 7.3L Power Stroke (1999-2003) :: Ignition Lock Cylinder Removal With No Key
So I have a replacement steering column for my truck and need to swap out lock cylinders. My question is; since there is NO key, is there any way to avoid drilling out retaining pin. If I did drill it out am I entirely screwed'?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Doing Clutch - Slave Cylinder Removal
I'm getting ready to swap my clutch and got to looking at the slave cylinder. I read somewhere that you have to rotate and twist it to get it out? Or something else? Also after reinstalling how do you get the slave plastic piece cut that holds the rod in? Or do you just push the clutch?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Back Doors Won't Open From Either Side
I have always been afraid this day would come - that the engine would outlast the door and window systems.
I have never previously in life wanted a vehicle with electric assisted windows and doors for this reason - remember when those were expensive foo-foo options on a vehicle?
Anyway the back passenger door window has not worked for a couple years now. Not too big a deal.
A month ago the back passenger door could no longer be opened from either side. Not too good and I couldn't see much of a way to ever fix it.
This morning the back driver side door won't open from either side. The lock only half-heartedly wants to unlock via the powered system though it can be fully pulled up manually (not as possible on the passenger side rear).
Next up will be the front doors...
Ford 7.3L Power Stroke (1999-2003) :: HPOP Hose Leak At Cylinder Head
I have an oil leak where the HPOP hose attaches to the cylinder head. I have the removal tool for the hose. I assume I need a new fitting. What's the torque spec for this fitting, and any additional tips I need for doing this repair?
View 11 Replies