Ford 7.3L Power Stroke (1999-2003) :: P0269 Cylinder 4 / P0284 Cylinder 8 Running A Little Rough
So I did a cylinder contribution test and a buzz test today. It buzzed evenly on all cylinders. Then when I did the cylinder contribution test I got these codes,
P0269 cylinder 4 contribution balance
P0284 cylinder 8 contribution balance
It has been running a little rough lately but not smoking. Seems to be chattering more than it was too. I did the FRx, HPx, CVDs and banjo bolt mods about 500 miles ago and it was a lot quieter and ran better. Just recently started running rough and a little louder. Could these injectors be bad? I did new injector O-rings about 800 miles ago. I ran the test with the engine cold and with it warmed up and got the codes both times. It seems to have a little bit of throttle flutter when holding it about half throttle while driving.
As far as I know the injectors haven't been replaced and they have 186K miles on them.
2001 F-350 Lariat Dually Supercab 6-spd manual 7.3 Powerstroke Turbo Diesel 186,000 miles....
Ford 6.0L Power Stroke Diesel :: 2004 F250 Running Rough Intermittently
Ok, so I have a 2004 F250, with 6.0L. when driving at a steady speed (doesn't matter what speed), the engine will run rough when coming to an idle, and stay running rough until I shut it off and let it sit for a bit.
After I cycle the key a few times it will fire up and run fine, so I came to the conclusion that air is getting in the fuel system. I then took the filter cap off that is located in the engine bay and cycled the key, which produced a lot of bubbles, which I am assuming shouldn't happen.
I guess my question is, should I have air bubbles in the filter bowl, when cycling the ignition?
Ford 6.0L Power Stroke Diesel :: 2007 - Won't Start Intermittently - Running Slightly Rough
I just bought a 2007 6.0 with 239k miles on the truck, it has EGR delete and ARP head studs. When i bought it the owner warned me of injector stiction...
I drove the truck for about a week, changed the oil over to Rotella T6 with archoil, and swapped out the air filter so far. (previously was non synthetic rotella). I drove the truck 2 more times since changing those two items and then i had a no start issue.
Scanguage2 said it was FICM sync.....so i messed with the wire loom, and got it to start twice but it died right away. (it had ficm sync, then it died and went back to 0) So i ordered a CPS pigtail and was going to change it out today.
Today i went out and pushed on the CPS sensor directly, charged both batteries and the truck started rough but kept running after two times (still haven't changed the pig tail)
Now it starts but is still running rough.
Scangauge 2 Running:
IPR : 23.8
ICP : 581
FICM SYC : 1
FMP : 48.5
The only code i'm getting is P0269 which I'm hoping is only injector 3, a bad injector wouldn't cause all this would it?
I'm just trying to figure out what i should look at next.
Ford 6.0L Power Stroke Diesel :: Intermittent Rough Running At Idle
In your experience, what issues have you seen that caused intermittent rough running at idle, but did not throw a code. I have monitored (with numerous scanners/gauges) this 6.0, but cannot get a code or see any of the sensors out of spec.
At Hot idle:
IPR: 24.2
ICP: 640
ICV: 0.90
MAP: 14.7
MAF Volts: 1.5
EOT/ECT Deltas within 10 and Avg ECT=192, EOT=199
EGR Valve cleaned and EGR demanded = EGR Measured
Vehicle will run rough after long runs or towing. Cylinder Balance test showed all injectors on. What could be the cause?
Ford 6.0L Power Stroke Diesel :: Running Rough - CEL On With Code P2285
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
Ford 6.0L Power Stroke Diesel :: 2006 F250 Running Rough At Idle
I have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 RepliesFord 6.0L Power Stroke Diesel :: Running Rough And Pending Code P0624
So I have been chain a no hot start issue. Found a bad top o ring seal for injector #2 replaced the o ring put it all back together did an air test seemed good not 100% sure I don't have another leak. Still problem starting. But I am now running rough and I have a pending p0264. What's up?
View 10 RepliesFord 6.0L Power Stroke Diesel :: Powerless And Rough Idle Until Reaches To Running Temp
I have a 05 6.0l. Egr deleted. And my truck has a rough idle and power loss. Ive tested the ipr and the icp and they are reading at specs. I've also replaced the Hpop about 1500 miles ago. It has a real rough idle until it's at running temp. And it has power loss, I'll be driving down road and theres no where near has much power has there should be. And the idle will jump between 1500 rpm and 2000rpm.
View 9 RepliesFord 6.0L Power Stroke Diesel :: Running Rough - #2 Contribution / Glow Plug / Injector Code
#2 contribution/glow plug/injector code ????? Harness looks good. What's the malfunction?? Runs rough. Never seen those 3 codes together.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Rough Idle - Code P0270 - Bad Injector?
my excursion just started hard and had rough idle one morning then code P0270 - injector, FICM or wires between are the logical choices I think.
started with wires - all connections good at FICM and injectors (applied dielectric silicone) - checked all 4 wires from injector connector pins for resistance with omh meter from X-1 connector. no change
so next is FICM. couple years back sent to ed for repair. if I remember right it was power supply side only so the "brain" side might have gone? good news is could I get a loaner FICM off fellow 6.0 and installed (can't confirm condition of loaner - trucks been parked a while) same code same cylinder - no change.
I read somewhere possibly swapping two injectors (say 2 and 4?) and see if the code follows the injector or stays with the cylinder, further test for a bad FICM
Is that necessary? I would hate buy and replace the #4 injector just to put it back together to find no change then forking over 6 7 hundred more on a new FICM.
Ford 6.0L Power Stroke Diesel :: 2005 - Stuttering And Running Rough - Blackish Grey Smoke / Code PO269
2005 6.0 133000 miles... Truck has been stuttering and running rough for about 2 weeks, warms up and is somewhat better. Would stutter in the RPM range of 1600 to 2100 RPM, can push down on accelerator and power through it with no problems. Checked codes and got PO269 Contribution Cylinder 3. Changed all filters and oil change along with a bottle of hot shot secret in the oil. Truck is now blowing blackish grey smoke under throttle and when idling that smells like fuel. No coolant in oil, and no oil in coolant.is the injector shot, or injector sleeve bad?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Rough Idle And Loping Upon Cold Start - P0488 Code
My '05 Excursion recently started having rough idle and some loping when started cold. It seems to run good and idles pretty good when it warms up. I'm also getting a P0488 code (EGR Throttle Control Circuit A Range/Performance). I do have a BPD EGR and I don't recall if that would throw a code alone? I'm taking a trip next week and want to get it straightened out. Does it sound like an EGR valve issue?
I also thought about a battery issue, I know that can cause weird problems. I have Duralast batteries and they always seem to fail at about 2-3 years. I took it in and they say it tested good but I'm not always sure with them. Long story, but when cranking for longer than normal, the cranking power would drop quite a bit. Checked battery and had some corrosion. Cleaned and upon further inspection, the positive post is a bit eroded at the base and sunken in. The voltage was about 12.35 after sitting all night, a couple of the cells were reading lower than the others (about 50%, other 75%) when checked specific gravity. I tested voltage after batteries had been in the truck overnight, then unhooked from truck when testing.
I also thought about a glow plug/harness issue. The truck cranks for awhile before starting, 5-6 seconds sometimes, but not all the time. It starts up pretty quickly when warm. That's been going on for some time. Anyway, I will try to get a video of the rough start after cools down.
Ford 6.0L Power Stroke Diesel :: Running Rough - Code P0404 - Black / Whitish Smoke Coming From Tail Pipe
Truck started running rough on way home the other day. First gave me P0404 code and would get black smoke along with whitish smoke coming from the tail pipe. I haven't been able to notice or track an amount of coolant loss yet.
Swapped EGR valve this morning and now noticed this once she kicked into high idle (still warming up). About to hook up the IDS, hoping I this is not head gasket .
[URL] .....
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Rough Idle / Cylinder 4 And 5 Contribution Balance Code
2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.
Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.
So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.
Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?
Ford 6.0L Power Stroke Diesel :: Dies Intermittently While Running?
Dies while driving down the road and usually will restart with no problems.Seems to happen more often when it gets hot out. IPR/ICP are good.It took a long time to start once also. I'm leaning toward fuel pump but ?
View 14 RepliesFord 6.0L Power Stroke Diesel :: No Start - Running Rough?
Well, I've read a lot of threads on this problem! Try to do my own repairs, so I'm learning and not spending a lot of cash at repair shops.I have an 04 6.0 Super Duty Crew. Starting running rough on way home. Pulled over ,then it died.wouldn't start. Had towed home. Replaced ficm circuit board. No start. Replaced Harness,
icp...... ipr Sensors. Still no start. I noticed there is another circuit board inside ficm. Should I have bought the whole ficm unit?
Ford 6.7L Power Stroke Diesel :: Running Rough / Reduced Engine Power
I am having a problem with a 6.7. The truck has 9900 miles on it. It has a dpf delete, egr delete, Spartan tuner and a snow stage 3 kit. The truck lopes at idle but once throttle is applied it levels out but still runs a little rough. Its keeps saying its in reduce engine power no matter how many times I clear the code. If I clear the code it will come back in 2 seconds with out cranking the truck or anything. Rail pressure is telling me 31090 psi and not changing running or not. I have changed rail pressure sensor, and pressure control valve with no result. The green and violet 5 volt reference that feeds those sensors is only putting out 1.2 volts. Put a new pcm in it still the same and now has quit running totally. The codes are P0193, P0335,and P06A6.
View 14 RepliesFord 6.0L Power Stroke Diesel :: High Idle Mod - Intermittently Blowing Fuse
I completed the high idle mod on my '05 Excursion 6.0 a few months ago. The 12V source is the blue/white wire that up/right of the ODBII connector outlined in the high-idle mod how-to.
For some reason, every couple of weeks, the 10-amp mini fuse at #29 will blow. It will work well for several weeks - then randomly pop the fuse about once a month.
Not sure if maybe I should swap out the switch I'm using to toggle the high idle, or maybe if an increase in the fuse amperage is required...or something else?
Ford 6.0L Power Stroke Diesel :: 2006 - Hesitates Intermittently - Stumble At Idle?
I have a 2006 F-250 4x4 with no cat, and no egr but the valve is still connected. It has about 146,000 miles. Just recently when warm, it has a slight miss every once and a while when stopped and in gear. Just a slight drop in RPM then recovery. Its mainly used on the highway and 99% of the time I set the cruise and its smooth as silk. Every once and a while I feel it stumble once or twice, recover and it is fine for the next 80 miles with no issue. It started as once every few trips but now It seems to be happening at least once every other. I use Motorcraft filters (maybe 6K on the fuel filters) and rotella oil. My scangaugeII shows no codes and no Injector pressure issue (1200-1400 at 75 mph depending on grade) and the FICM voltage stays between 48.5v and 49.0V. What should I check?
View 2 Replies