Ford 7.3L Power Stroke (1999-2003) :: Diesel Smell Coming On And Off - Fuel Bowl Leak?
I've thought I smelt diesel fuel on an off for a while, but never found the source.
Tonight, 17 degrees out I have fuel in the valley and it appears as if the back of the drain valve is wet.
A fuel bowl rebuild is on the short list. Is this typical, the cold weather brings the issue to light?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Fuel Leak - Not Water Separator Valve O-Rings
I have a very small fuel leak in my 2001 F-250. I was going to just let it go until I needed to do other work (since I get 20mpg city and 25mpg highway), but I went to a "new" inspection guy, and he flunked me. So now I have to fix it. And for all I know, my mpg and fifteen other things will break when I try to fix this.
Today I spent 4 hours in the heat putting in two new o-rings on the water separator valve. But the truck still leaks fuel. Climbed up on top of motor while it was running and looked, but I don't see where the fuel is leaking out.
Online research suggests to me that the next most-likely culprit is a steel fuel line that wears through from vibration and chafing. Is that correct?
This truck is so eaten up with rust (came from salt belt) that I bought a LOT of fuel line stuff a year or so ago, so that when things started falling apart from rust, I would have the parts on hand.
Now I'm wondering whether I already have the part I'm likely to need.
So far, I have bought:
1. Dorman Fuel Supply and Return Lines
2. Riff Raff Diesel High Pressure Crossover (HPx)
3. Riff Raff Diesel Fuel Rail Crossover (FRx)
So my question is, am I likely to have something to replace the part that commonly leaks on these trucks due to vibration/wear/chafing ... or will I still need to buy another part?
I'm thinking that one of the two lines in item #1 above is the problem child...
Ford 7.3L Power Stroke (1999-2003) :: Return Line Leaking At Fuel Bowl
New to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
Ford 7.3L Power Stroke (1999-2003) :: 90 Degree Elbow Not Fitting The Fuel Bowl?
Trying to fit my edge fuel pressure sensor. I have a 90* fitting from Diesel O-rings and I can't seem to get the 90 elbow to turn all the way down before it makes contact with the fuel bowl housing. I'm using the drivers side port, should I use the passenger side port? would it have more clearance than the driver side port?
My instinct is to crank it all the way down then tighten the nut, should I just screw it in until it makes contact then tighten the nut? I was worried it wouldn't have enough threads in contact to seal as well as it should and leak.
Ford 7.3L Power Stroke (1999-2003) :: Regulated Return Fuel Bowl Delete
I want to build a fuel bowl delete/regulated return fuel system for my 2000 f250 . I would like to make a really neat kit and attach all products used so people that want to build their own would have a useful source. I understand that it will probably cost the same but I want to design my own and route it the way I want . I have 3/8 1/2 5/16 and 1/4 stainless tubing as well as a bunch of unions and 90* 45* fittings and a couple tees. What size is the ports for the fuel lines that go into the four corners of the heads . I am a pipe fitter pipe welder by trade so this is basically a mini version of what I do everyday at work. Looking for some size details of the head port sizes so I can get the correct fittings?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: New Fuel Bowl Drain / Water Separator Failure After 3 Weeks?
Had the ole factory fuel separator/bowl drain start leaking on me about a month back. So i ordered and installed a new one, issue fixed. Well last night the fuel leak started again, I looked everywhere and i cant see anywhere else it may be leaking at. I felt the underside of said piece and it didn't feel wet, but the valley is full of fuel.
I got in there and tightened the 4 bolts down some more, they were tight but i got a some turns on em and am hoping i either didn't tighten it down enough or they maybe backed out some. Now just gotta see if that solves the problem, again.... the replacement is a doorman, the o-rings were bigger/thicker than the factory orings on the old part, of which the o-rings were shot.
Like I said once i replaced the part the leak stopped for 3 weeks until last night. If the tightening of the bolts doesn't solve it where should I look next? I have an FRX mod but i checked all that and its dry as a bone around all the fittings by the bowl and the heads. No indications of leaks anywhere around any of the FRX assembly.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Filter Bowl Drain Valve Replaced - Emission System Warning Light
I just changed the drain valve on the fuel filter bowl. All went well and no more leak, but now I am getting an "emission system" warning light.
After I replaced the valve, I filled the fuel bowl with diesel fuel. Was there any other priming that needed to be done (if any)? What the emission system warning light may mean?
2002 F250 7.3L 4x4.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Oil Leak And Inconsistent Idle
2001 F250 7.3L 280k... On a 50 ish degree day or if the truck is cool on a warmer day I'm getting an inconsistent idle lowest end 450rpm high end maybe 750. Wondering now what the possible causes may be, truck seems to run fine and idle ok once warmed up but still cycles the revs a little, AC is off.
Second question is about an oil leak, doesn't seem to be massive but it leaves a small pool, especially if she's plugged in. It seems to be coming from underneath the truck driver side large metal tube system running front to back on the engine, just under the manifold I think.
I checked HPOP connections and they are solid no leaking but here's a pic from under the truck, can't see any of this from the top. Is it an easy fix??
Ford 6.0L Power Stroke Diesel :: 2003 - No Start / Fuel Not Getting Into The Upper Bowl
2003 6.0 no start. turn the key to on and nothing happens. dash lights up as it should but I don't hear the glow plugs cycle and no fuel gets into the upper fuel bowl. turn the key over and nothing happens. No starter click nothing. tried the starter wire to the battery trick and it cranks but does not kick over. checked ficm wires and they are secure as well as the injector wire on the intake manifold. it is the original ficm.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Idling Like Going To Run Out Of Fuel / Bad ICM Code
I have a 2001 f250 7.3. Recently started this problem idling at 1000 Rpms when stopped completely and when I let off the gas pedal it idles real funny like it's fixing to run out of fuel. It does not do this all the time however. At times it runs great. I had my mechanic scan it and at first it was the exhaust pressure sensor. Replaced it and it ran fine for awhile and it started doing again. Took it back in to get re scanned and it was throwing a bad ICM code. Replaced this as well and I'm still having the same problem. Had it scanned again and it's not throwing any codes now. I have no check engine light on and as long as I'm on the gas pedal it runs great. It's just when I roll up to stop or when I'm stopped completely. Again it does not do it all the time.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Big Fuel Leak?
Brothers of fte. I reach out. Tonight it appears I had a fuel bomb under the hood.
I've been chasing a fuel leak. Replaced fuel drain orings but one screw seemed to not snug up. Also the plastic was so brittle I couldn't replace the inner oring. Installed new valve worked great. A week later noticed new slow drips. Replaced fuel filter. Again good for two weeks.
Tonight pulled into the driveway hopped out immediately smelled diesel. Steaming from under hood. Popped the hood and everything was wet. Moved her to the street and it clattered like I was running out of fuel. Still half a tank though. Hosed of the drive. Popped hood again fired it up easily. Started fine. No noticeable leak. But everything is wet from fuel. Insulation on hood was saturated. When I open the hood fuel ran out of the insulation into the air intake. Batteries were wet!
Alright what gives? Do I have to be under load to see this leak?
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power Getting To Fuel Pump
There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 RepliesFord 6.0L Power Stroke Diesel :: Upper Fuel Bowl Be Empty After Sitting For 30 Minutes?
Should the upper fuel bowl be empty after sitting for 30 minutes?
I believe no. Which would indicate to me a stuck open injector which Iv been suspected of. Iv been trying to track down a miss that I have and Iv been suspicious of a bad injector but ain't been able to pinpoint which one yet.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Oil Or Fuel In Coolant?
I have a 2000 F250 7.3L and I pulled this from the overflow tank. I'm thinking it's oil since my oil cooler is leaking but just want to make sure it's not fuel and need to do injector cups...
View 2 RepliesFord 6.0L Power Stroke Diesel :: Truck Starts / Running Rough Then Die - Fuel Draining Out Of Bowl
2004 F550 with a 6.0. I had to clean out my fuel tank, replace the HFCM and filter on top of the engine. When I start the truck it will run for 30 seconds or so, start running rough then die. I opened the cap on the fuel filter housing on top of the engine to make sure the fuel was getting there. I turned the key on and the fuel bowl quickly filled up.
After a short time however, the fuel drained out. To where I do not know. I don't think this is normal as every time I've changed the upper filter on a 6.0 it is always full of fuel. Why could this one be draining out and could that be the issue why the truck dies after starting and running for a short period of time. I changed the o-ring on the cap and the new HFCM was purchased from Ford.
Ford 6.0L Power Stroke Diesel :: Low Fuel Pressure - Hissing / Air Noise At The Upper Filter Bowl
I have an isspro gauge and did the blue spring about 5 years ago. Since then my fuel pressure is in the 65psi range.
Last week it dropped to 50-55 normal driving and I figured the HFCM was on it's way out (195,000 miles). Replaced the HFCM and the pressure was a bit higher, but not back to it's usual range. Then pulling the boat home from the lake a couple days ago, I saw it at 45psi. On a couple hills it went as low as 40 psi, so I was getting gripped...coasting downhill it only went back up to 50 psi and no higher. Got 'er home and currently not driving it.
In garage with Key On Engine Off, during injector buzz, I can hear a hissing/air noise at the upper filter bowl. Also, the bowl drains empty once the pump cuts off and the sound of air stops too.
I am hoping it's a regulator issue, but I don't know if they are known to wear out or go bad, or if something else in the upper filter housing went bad. So I ordered a new upper fuel filter housing which also has the oil filter tower attached and I'm assuming that these new units would come with the blue spring upgrade already done.
I can check for codes tomorrow when I bring my computer home from work, so I haven't checked for codes yet. I pick up the new filter housing tomorrow and will periodically check back here during the day tomorrow.
Also, while I'm at it: the new HFCM doesn't have the heater. Can I just leave the old connector from the harness un-connected to anything?
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Electric Fuel Conversion?
So I'm not sure if I should post this here or in the 1994.5-97 section. The reason being I have a 2000 f250 with a 97 7.3. It currently has a mechanical fuel pump but they keep crapping out. We dont have the money to do a $600 diy conversion so were looking for a cheap solution.
So the 2000 has all the fuel lines and plugs to put a electric fuel pump in, but if I just threw a electric pump on then it would feed to the mechanical fuel pump which I'm guessing is a no no? Or possible?
If I put the electric fuel pump would I just have to remove the mechanical fuel pump and run lines from the pump to the bowl?
If the fuel bowl can't hold the pressure of an electric fuel pump then would I be able to swap the fuel bowl only and be good to go or is that impossible?
Let me know what you think were trying to do this as cheaply as possible.
2000 f250 auto 4x4, 97' 7.3 motor.
Ford 7.3L Power Stroke (1999-2003) :: Fast Steady Leak From The Fuel Rail Outlet Fitting While Running
I had just replaced my the fuel pressure regulator in the fuel bowl because it appeared to be leaking from where the FPR is, now with the new FPR , it is no longer leaking from there but now leaking (fast steady leak while running) from the fuel rail outlet fitting... How do you replace these, why all of the sudden it started leaking there ???
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - 4x4 Not Working
I have a 01 f-250 7.3 6 speed. I bought the truck a few days ago and the 4x4 wasn't working the dealer replaced the transfer case motor. I have another 01 f-250 that i have been switching parts out of to see if that makes a differences and found nothing to work. Ive switched the switch on the dash out and nothing. Ive switched the two relays under the hood and nothing. I have also checked all fuses. and the connectors on the transfer case.
So I finally popped the covers off the two relays and squeezed them with my fingers and boom transfer case locked into 4lo and then i can squeezed the other and boom back in 2h! So now I'm lost, I know the wiring from the relays to the transfer case is good and the switch is good and relays are good so I'm at a loss.. Also cruise control isn't working idk if that could be related i don't think it is but idk?