Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Oil Leak From Fuel Bowl?
I've had an engine oil leak for some time. Recently I've had to add about a quart a month. I got some fluorescent dye and added it to the engine oil last time I added a quart. Ran the engine for a few weeks. Then cleaned the engine valley with cleaner and hot water.
Tonight I investigated the top of the engine with a black light. To my surprise, the oil leak is coming from the fuel bowl, right around the drain valve. I can clearly see about a drop every 3 seconds of fluorescent yellow liquid falling into the valley below and yellow all around the valve.
I expected a leak from the HPOP not the fuel bowl. Do I have a bigger problem? Is engine oil getting into the fuel? I plan to replace the seals in the fuel bowl, but not until I know whether I have a larger problem to address.
2001 F250 Crewcab, 220,000 miles
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - P1247 Code Pending
Alright I have a 01 F250 with the 7.3L in it. Recently had the turbo rebuilt and all the surrounding gaskets changed as well as boots. All this was done around 1,000 miles ago. Runs great and I don't see/feel any issues, no white smoke anytime, little black when I turn up the tuner and really ride the thing but normal driving none. Problem is I have a pending P1247 code that after a few days will throw a CEL... I'm not sure what the problem is and have been searching the forum and people are mostly saying they get it but the boost drops or there isn't any at all and the truck my stall or bog down. I don't have any of those problems. Turbo spools up to whatever I want and I've never had it stall or bog or even get close... So what should I check? Also new to the site and diesels.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Airbag Indicator Light On For Code 47
About a year ago, my airbag indicator light threw a code 47. It did this for about two days, then it stopped. Fast forward to this weekend, and it started again. From what I can tell, it is the passenger side seat belt pretensioner. It could be a coincidence, but my daughter pulled the seat recline lever without anyone being in the seat, causing it to fly forward as if James Bond was ejecting someone through the windshield. The next time I started my truck, it was throwing the code. I tried to check to see if the plug was knocked loose during the ejection sequence. I thought the connector was under the passenger seat, but I don't see any wiring (the passenger seat is manual). My next guess was behind the glove box, but I'm not sure what I'm looking for.
My truck is a 2001 F250 4x4 Lariat.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Fuel Leak - Not Water Separator Valve O-Rings
I have a very small fuel leak in my 2001 F-250. I was going to just let it go until I needed to do other work (since I get 20mpg city and 25mpg highway), but I went to a "new" inspection guy, and he flunked me. So now I have to fix it. And for all I know, my mpg and fifteen other things will break when I try to fix this.
Today I spent 4 hours in the heat putting in two new o-rings on the water separator valve. But the truck still leaks fuel. Climbed up on top of motor while it was running and looked, but I don't see where the fuel is leaking out.
Online research suggests to me that the next most-likely culprit is a steel fuel line that wears through from vibration and chafing. Is that correct?
This truck is so eaten up with rust (came from salt belt) that I bought a LOT of fuel line stuff a year or so ago, so that when things started falling apart from rust, I would have the parts on hand.
Now I'm wondering whether I already have the part I'm likely to need.
So far, I have bought:
1. Dorman Fuel Supply and Return Lines
2. Riff Raff Diesel High Pressure Crossover (HPx)
3. Riff Raff Diesel Fuel Rail Crossover (FRx)
So my question is, am I likely to have something to replace the part that commonly leaks on these trucks due to vibration/wear/chafing ... or will I still need to buy another part?
I'm thinking that one of the two lines in item #1 above is the problem child...
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 7.3L Power Stroke (1999-2003) :: SES Light Came On While Idling At A Stoplight - Code P1316
Well, truck is throwing me for a new loop the day I pick it up from the body shop (crazy, right?). I started out driving it and had a blue haze - I figured it had some air left in the system from doing my injectors so I left it and it cleared up after about 20 miles. I noticed that my SES light came on while idling at a stoplight, but went off when I took off. Figured it was a fluke and kept on getting on.
Well, next light it does the same thing - idle the light is on, take off the light is off. Reading the code yields P1316 - so I pull over and running a buzz test to fetch the IDM codes. Guess what? No codes. All sounded fine, so this is where I got really confused as I'm getting huge mixed signals from this truck suddenly.
As I got to watching my gauges, I noticed that I was idling around 10.8 IPRDC and 530-560 ICP, and when I would get about 16-18 IPRDC the code would go away. Did a near-WOT run when getting on interstate as a test to see how it'd do, and saw IPRDC get up to 98% - the highest I have EVER seen it get on this truck (no idea if it is related or not). I have a log from moving around the lot that I will try and upload soon.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power Getting To Fuel Pump
There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Oil Or Fuel In Coolant?
I have a 2000 F250 7.3L and I pulled this from the overflow tank. I'm thinking it's oil since my oil cooler is leaking but just want to make sure it's not fuel and need to do injector cups...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Showing P1277 Code?
My truck is showing code p1277. The only time I really notice anything is cold mornings like we been this week. Low 50s. When I first start it in the morning the engine light goes on and off until the truck is completely warmed up. Could it be the injector going bad?
2003 f250 7.3 with 415000 miles. Stock injectors
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Electric Fuel Conversion?
So I'm not sure if I should post this here or in the 1994.5-97 section. The reason being I have a 2000 f250 with a 97 7.3. It currently has a mechanical fuel pump but they keep crapping out. We dont have the money to do a $600 diy conversion so were looking for a cheap solution.
So the 2000 has all the fuel lines and plugs to put a electric fuel pump in, but if I just threw a electric pump on then it would feed to the mechanical fuel pump which I'm guessing is a no no? Or possible?
If I put the electric fuel pump would I just have to remove the mechanical fuel pump and run lines from the pump to the bowl?
If the fuel bowl can't hold the pressure of an electric fuel pump then would I be able to swap the fuel bowl only and be good to go or is that impossible?
Let me know what you think were trying to do this as cheaply as possible.
2000 f250 auto 4x4, 97' 7.3 motor.
Ford 7.3L Power Stroke (1999-2003) :: F250 Getting Hard To Start / Code P1670
But it starts. '99 F250 PS. Had code P1670, cleared it. No other codes. Started truck back up and ran KOER test with AE(which I'm not very good with). The code did not come back. It is hard to start plugged in cold or warmed up. I have WTS light and it goes out(glow plugs are original). RPMs are slow to come up (almost starts before it kicks in). Doesn't matter if fuel tank is full or not. Oil level is fine. Batteries are charged and check good. Starter checks out ok. Buzz test was ok. Now when I run KOER do I need to do anything other than hitting the initiate button?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - 4x4 Not Working
I have a 01 f-250 7.3 6 speed. I bought the truck a few days ago and the 4x4 wasn't working the dealer replaced the transfer case motor. I have another 01 f-250 that i have been switching parts out of to see if that makes a differences and found nothing to work. Ive switched the switch on the dash out and nothing. Ive switched the two relays under the hood and nothing. I have also checked all fuses. and the connectors on the transfer case.
So I finally popped the covers off the two relays and squeezed them with my fingers and boom transfer case locked into 4lo and then i can squeezed the other and boom back in 2h! So now I'm lost, I know the wiring from the relays to the transfer case is good and the switch is good and relays are good so I'm at a loss.. Also cruise control isn't working idk if that could be related i don't think it is but idk?
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Airbag Light Is Staying On / Code 25
Just bought a 2002 F-250 4x4 Off-Road Crew Cab 7.3L and the airbag light is staying on. I have found out after the fact that the truck has been previously involved in a front end collision. The damage was to the passenger side front. I turn the ignition on, the airbag light will come on solid (just like all the rest, with the exception of the 4x4 and 4x4 low) then go out. Then it flashes slowly 2x then 5x, then goes out for a bit then repeats a few times before staying on. This tells me I am getting a code of 25. I have searched with no luck to narrow this issue down. Everything mechanically works, cruise, horn, etc. The only thing I can find wrong is when I engage the 4-wheel drive (floor shifter) the indicator lights do not illuminate in the instrument cluster. Neither the 4x4 nor the 4x4 low. I am unfamiliar with this truck, so I don't know where to began searching. I cant afford to take it to a dealer and I have children in the truck quite often, so I would like to remedy this very quickly.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Missing And Jerking - Code P0541 / P0640
1999 F250 7.3 .. The truck seems to idle fine and and runs smooth all the way up top cruising speed, but when it levels out at say 65mph then it starts missing and jumping. I can ease into the throttle a little and it smooths out up until it levels out again.
I have the Vgate Elm and Car Guage Pro and a couple of other apps and the only DTCs I'm getting anymore are:
P0541 Intake Air Heater Circuit Low
P0640 Intake Air Heater Control Circuit
But from what I've read, neither of those should cause this issue.
Buzz test sounds good.
Cylinder Contribution test throws code for #4 Cylinder
I'm trying to do everything possible before throwing an injector in it.
Ford 7.3L Power Stroke (1999-2003) :: F250 Will Crank / Hesitate / Start And Die - Code P0231
Okay, I am having issues with a 1999 F250 XLT 7.3 with diablo programmer. I have searched and searched and have tried everything we could think of and it is a no go. The truck will crank, hesitate to start, start and die, other times it will only crank and not run at all. We can make it stay running by hitting the accelerator. The only code we were getting was the cps code, but that is suspected to be because of the excessive cranking and no start times. Previous to this issue getting this serious it would stall randomly, at idle, going down the road at constant speed, slowing down, or accelerating. We now have code P0231.
Through this we have tried:
IDM
(loaner) ECM
removing Diablo
3 CPS
shaving down CPS
Shimming CPS
IPR
Fuel pump
relay
fuel pump fuse
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Fan Clutch Comes In And Out Rapidly
The fan clutch will come in and out rapidly when NOT in OD and pulling hills with the fifth-wheel attached. Replaced with a new aftermarket fan, then a new OE one. Then had the radiator pulled and all the bugs, etc. blown out. The condition has not changed at all. The original fan clutch was pretty sloppy. There are no codes, the trans fluid is nicely red, the engine does not overheat or even change temp when pulling hills. No check engine light ever. The truck is a 2001 F250 4 X 4 automatic extra cab with 7.3 engine without any modifications and runs perfect except for this. There are about 95k miles on odo. When we use overdrive on the flats, there is no issue.
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Cranks But Won't Start
I have 2001 7.3 f250 ... I just got it about 2 months ago I drove it for maybe 2 week and it ran good the other morning I went out to start it and would not start and the way I was parked my low fuel light was on so I put 5 gallons of fuel in finally got it started sum how drove it for maybe 2 hrs parked it and wen we got back in to go it was done for hasn't started since its been down for a bout 2 weeks now I've replaced hpop, icp, pcm, fuel filter,checked idm for corrosion it all looks well, gpr,checked uvch on driver side looked good and changed cps what else do I have to go from ? No matter what it won't start good batteries cranks good but no start ...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Will Die For No Reason
01 f250. Just bought from my brother. 140000 miles. Immaculate. Truck will die for no reason. Running down the highway, or sitting at a red light. Fires back up. Sometimes have to crank a few times. He has had at a mechanic and everything checks out good. Since birth its only had royal purple that he has changed every 5000 miles as well as all filters. Where do I start?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Died And Won't Start
2001 f250 7.3 with 210,000 miles. Was running rough when cold and glow plugs were bad so I bought new glow plugs and had injectors rebuilt with 100% over stock nozzles. When I changed them I made sure I turned the motor with glow plugs out and pulled the drain plug in the head. Wanted to start it just to get the oil out before I let it sit for a few days til I got the tuner. It started fine and I let it run while I ran in the house and when I came back out about 1 min later it was off. Didn't want to start again. Just left it til I got the tuner on and It still doesn't want to start. What I should check? Turns over good and has good batteries. Also it's a hydra chip tuner with beans tunes. Darren weeks rebuilt the injectors.
View 7 Replies