Ford 7.3L Power Stroke (1999-2003) :: 2002 7.3L Will Crank Forever But No Start (bad Fuel Pump)
I just got delivered a 7.3L from down south. Batteries were dead so replaced both. Fuel was a couple notches above red line (much closer to red line than 1/4 tank) so I added about 7-8 gallons.
It will crank forever and ever...Won't start.
With starter fluid it starts but not strong enough to pump the pedal and rev it up to keep it idling.
I know s-fluid is bad but if I continuously spray with key turned forward it will run but as soon as I let go of key it shuts off.
20 degree weather and it was delivered to a parking lot so I cannot plug it in.
Was told to check filter cap, turn key, and see if it fills bowl with fuel....if not then it is fuel pump. Someone else mentioned that it could be bad crank position sensor? Does this sound like fuel pump?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Fuel Pressure Gauge - Install Sensor Into Lift Pump?
I am installing a fuel pressure gauge into my 02 7.3 I went to the thread the sensor into the plug hole on the fuel filter housing and it wasn't threaded, turns out the sensor thread is slightly smaller and a different thread ... The directions say to install it into the filter housing or the lift pump ... So I'm assuming I have to go the lift pump direction of installing it but where the lift pump is or how to install the sensor into it while not throwing a code or causin problems ... A step by step and even pictures.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: No Power / Zero Voltage To Fuel Pump
2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
Ford 7.3L Power Stroke (1999-2003) :: No Power To Fuel Pump / Fuse 30?
I have a 2003 F250 and dont have power at fuel pump, or fuse #30. I put power directly to fuel pump and it worked and truck fired right up.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Started Losing Power Then Slowly Die / Fuel Pump Bad?
I was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranks But Won't Start - Fuel Pump Not Pumping Fuel
01 7.3. Cranks, won't start. Tank was at 1/4 but is full now. The lift pump runs, I can feel and hear that the motor is spinning when I cycle the key. I removed the fuel filter and cycled the key and get no fuel into the bowl. It looks like the lines are stainless from the pump to the tank so I doubt it is sucking air. I pressurized the tank with a shop vac and I get fuel coming into the filter housing. Am I missing something obvious? I have never seen an electric pump that would run and not pump fuel. I removed the suction line at the pump and don't feel any suction there.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To PCM Fuse
I just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To Reverse Light Sockets
I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Lost Power And Suddenly No Throttle
Comming back from hunting today my truck suddenly lost power and stepping on the accelearator had no effect at all. We were on the highway thru the mountains but on a fairly level stretch for a few miles. Managed to pull the truck and toy hauler over and the engine was running fine but stepping on the accelerator had no effect. The check engine light came on every time I stepped on the throttle and went out when I released it. It started fine but no throttle response. Switched around a bunch of relays and checked the fuses and still nothing.
Not liking my parking spot i tried to see if it would move down the road at an idle but it would not. Then I thought to try it in 4 wheel low and as the shoulders were soft it wouldn't move forward so tried reverse and went back a foot, forward again and moved a foot and a half. did this several times and all of a sudden the throttle responded, took it out of 4 wheel and it ran fine all the way home. What would have caused this? I was ready to call a tow truck which would have been several hundred dollar bills for where we were and with the trailer
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 7.3L Power Stroke (1999-2003) :: Relay For Fuel Pump Keeps Going Bad
The relay for the fuel pump keeps going bad. Is this a sign my fuel pump is going ? I just replaced my 2nd relay ( lasted about 1 week ) 1st lasted 16 years. Or is there another issue to look at ?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes
I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Fuel Pump Fuse Blown
So the other day my 20amp maxi fuse for my fuel pump decided to blow, put a new one in & everything has been going good since. Is it just a fluke or is this an indication my pump is going out? I inspected wires off the pump & connections for corrosion & that's good, fuel filter is also new about 2 months ago & I always run #1 diesel with a little additive in the winter.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Electric Fuel Pump Conversion
I was wondering if it is possible, due to budget, to perform the electric fuel pump conversion in steps. By that I mean could I remove the mechanical pump and install the electric pump on the frame, but retain the stock filter housing and regulator? I would use high pressure hose and run from the stock pump supply line on top of the engine to the fuel bowl inlet and then use high pressure to run to a three way fitting, and a bit more hose to join the fitting to the stock lines running to the head. later as budget allow I will replace the filter assembly and regulator and then the lines to the heads.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Water Pump Replacement
How hard is the water pump to replace on 1999 f250 7.3 ...
Any thing special i need to know before tackling this job ...
Also is there any step by step instructions ???
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Fuel Pump Location?
Where the fuel pump is located on a 2000 F-350 7.3L Diesel? Also, how complex is replacing this?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Fuel Pump Runs Only When Low Beam Lights On?
Went to start my truck (2003, 7.3 F250) one evening and I found the headlights on. No keys in the ignition and the truck hadn't been driven for 2 days. There was a strong smell of plastic and or electrical components burning in the cab. The truck started without a problem. I shut it off and the lights remained on. Cycling the MFS and light switch would not turn the lights off. I had to disconnect the batteries and leave it till time allowed for trouble shooting.
I've had it in my shop for three months now and this is what I've found so far.
-Source of the burn smell is coming from the fuse panel. More specific it's coming from a bulkhead that plugs into the panel. One pin connected to a White wire with 2 purple traces. I've traced this wire to one of 2 small relay packs in the engine compartment next to the driver side fender. I've replaced the relay this white/purple wire connects to as a precaution. This did not remedy my trouble.
-The local ford dealer told me this relay was for the A/C clutch. I located a 10amp fuse in position 10 and removed it. The headlights finally turned off.
-I started the truck and the A/C compressor clutch still engaged and ran. Smoke began to pour from the fuse panel once again. I killed the truck and head lights remained off. All done with the fuse in position 10 removed.
Here's where it gets weird!
-With the key/engine off and I turn the headlight switch on and MFS to low beam the fuel pump is running. Change the MFS to high beams and the fuel pump turns off.
I've looked over the wiring harness and there are no noticeable problems indicating multiple wires being shorted. How are all these issues related?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - No Start After Changing Water Pump
I have a 2001 F250 Super Duty V8 7.3 L. I removed the water-pump then waited five days for the oring for the new pump. I installed it and now the truck will not start. I have drained the fuel water separator and replaced the filter. On the passengers side through the kick panel I found that button popped out so I pushed it back in and still it will not run. It acts like its not getting fuel but if my fuel water separator is filing up I'm assuming mu fuel pump is working??
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Vacuum Routing From Pump To Hubs?
I am in the process of replacing the complete front end on my 02 CC 4x4. Im replacing the hubs the lockers all seals and spindle axles. complete brakes with power stop and stainless brake lines ......I am going to switch back to the original automatic lockers. I am curious if has a simplified one line for the vacuum routing from the pump to the hubs?
View 7 Replies