Ford 6.7L Power Stroke Diesel :: Getting Code PO088 / Power Reduced When Truck Flashed
I just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 RepliesFord 6.7L Power Stroke Diesel :: 2008 - P0128 Code / Truck Will Not Go Into Regen
I just had my thermostats replaced in my 6.4, and I'm concerned about the regent process. I read that when the P0128 code is thrown, truck will not go into regen. Is this true? How can I manually start the regen process?
View 1 RepliesFord 6.7L Power Stroke Diesel :: Truck Idling High - Code P0087
This morning I went to go to the corner to buy something, I knew it was colder than usual, -12F. I did not plug in the pre-heater last night. I let the truck idle for 15 minutes before moving it. It was still idling high. The P0087 code is the only code popping- is this just because of the cold temp? I haven't owned a diesel since my '79 Rabbitt, and this engine is as different from that as night is day. this didn't happen yesterday but it only got down to -2F and warmed up to about 18F.
View 6 RepliesFord 6.0L Power Stroke Diesel :: Code P0237 - Truck Won't Build Boost Over 11 PSI
P0237 code. The truck is a 2003 f250 with an edge evo . The truck will run great then throws this code and won't build boost of over 11 psi. Now it even drops it right off to 0. I replaced the map sensor a month ago and doesn't seem to have fixed anything.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Truck A Bit Sluggish At Takeoff - P132B CODE
Can a bad or lazy VGT solenoid cause a P132B code? I just recently had the turbo cleaned and the VGT solenoid replaced about 3 months ago. The truck is a bit sluggish at take off. Is there anyway to check the solenoid to see if its bad?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / No Crank - Code P2285
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesFord 6.0L Power Stroke Diesel :: Truck Shut Down While Driving / Code P2614
So a few day ago my truck shut down while driving. I posted up and checked the ficm harness as suggested. Things were a bit lose so I zip tied my harness around the ficm. Thought it was all fixed and test drove it and it shut down again. I tried to start it a few times and my ICP was a tad low about 450 ,I have a brand new ICP and harness. Checked my scan gauge and I have code p2614. I cleared the codes and the truck started right up. I need to get this sorted out I was supposed bro go home tomorrow from working out of town all week about 100 miles from home...
View 3 RepliesFord 6.0L Power Stroke Diesel :: Truck Hard To Start Every Time - Code P0284
Earlier this week the truck was hard starting every time. Tested the batteries: 12v engine off, 14v engine running, all good.
The next day it threw a P0284 – Cylinder #8 contribution/balance, and was clearly missing on a cylinder. Despite the lack of a puff of smoke at start-up, I was pretty sure it was an injector. So I ordered one from White Bear Lake, and a fuel pressure test adapter from Strictly Diesel. Then I decided to do some testing with AutoEnginuity. Tried the injector buzz test first and got a note that the truck was not capable of performing the test. Tried starting truck and gauges swept and wouldn’t turn over. Tested batteries again: main battery 11volts, aux 12volts.
I got the batteries in and the stupid thing runs like new. Only codes are P1000 and P0603. Truck passed the injector buzz test, and cylinder contribution test graph is almost a flat line.
Take-aways:
1. Bad batteries can cause all sorts of havoc.
2. Always use a voltmeter that displays tenths of a volt, because if it’s only showing whole volts, it could be rounding up. The 12 volts from my first test was probably more like 11.6 volts.
3. Always do as much testing as possible before buying parts.
4. Costco does not sell Kirkland batteries anymore. They only stock Interstate, and the Interstate warranty has dropped from 36 months free replacement to 30 months.
5. The Walmart and Autozone batteries with the five year free replacement are “out of stock” and I’m guessing they won’t be back with Interstate dropping their replacement dates.
6. Most of the car batteries in the US are made by Johnson Controls.
7. Motorcraft batteries did not get very good reviews.
8. Interstate said that AGM (absorbed glass mat) batteries stand-up better to the additional vibration and heat experienced under the hood of a diesel, but they are significantly more expensive, and not all the brands offer an AGM with a better warranty than their best lead-acid offering. Also, the guy at Sears said AGMs are only beneficial for newer cars that continue performing electronic functions after the ignition is turned off. He said he’s seen lead-acid batteries outlast AGMs, but didn’t specify if those were out of diesels or not.
Questions:
1. Can I expect the P0603 to go away after the drive cycle is complete?
2. What should I do with the new injector? If I return it there’s probably a restocking fee. If I wait for a complete injector failure I don’t get the core charge back until then. With the FICM compensation, I don’t know of any way to identify weak injectors without IDS.
Ford 6.0L Power Stroke Diesel :: Truck Died And Refused To Start - Code P0603
So I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.
Ford 6.0L Power Stroke Diesel :: Filled Up With Diesel And About A Hour Later The Truck Is Knocking And Idling Rough
Wtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 RepliesFord 6.0L Power Stroke Diesel :: Glow Plug Code And CEL Code P0675
Truck has been running very well while in the warmer North Carolina climate pulling trailers with no limp mode or wrench light. However, when daughter started the truck this morning, SGII showed one DTC and when she pulled it up it was P0675. OK, glow plug num 5 maybe or the module. No issues starting or rough cold idle. I told her to clear the code and we'll see if comes back.
She did ask if it is something she should have it repaired before the trip back to Vermont. So I thought I'd ping the group here since reading posts, they seem to be fairly easy to replace (and assuming it isn't a chafed wire) and I could probably save her some $. Just want to make sure there isn't any chance of real engine damage.
Ford 6.0L Power Stroke Diesel :: No Power / Bogging Down / Truck Barely Moves
My 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Truck Started Chugging Like Going To Die And Had No Power
First post since I bought my powerstroke. I was looking for some diagnostics.
On my way to work this morning and the truck started chugging like it was wanting to die and had no power, the pedal was to the floor and I was barely moving. I was able to nurse it to a parking space at work and pulled the codes, using the Torque pro. This was what I pulled:
P0284 - Cylinder #8 contribution/balance
P0299 - Underboost
P0611 - FICM
P0401 - EGR
P0671 - Cylinder 1 glow plug
On the way home I didn't even hit 5 miles and started into the same symptoms. So I decided to call for a tow, because my commute is about 60 miles one way. In waiting for the tow truck I disconnected the batteries and reconnected them thinking that it might "reset" something. I started it up and the same thing occurred, so I tried revving it up, and starting it up and shutting it down on and off for about an hour. Thinking I picked up some bad fuel. Drove it for a short distance and found things were getting better. I was able to make it home and pulled the codes again. It came up with these:
P0284
P0603 - Internal Control Mod.
P0611
P1000
Also on the ride home I had excessive amounts of black smoke from the exhaust and found a couple of large drops of oil on the driveway where i normally park, larger than what I normally see.
So my question would be what is the cause of all of this?
A little about the truck. it is a F250 CCSB with about 139xxx miles on the clock. I bought it from my brother when he had it he had the FICM replaced (with the 58V option) and the Bullet proof EGR installed. I replaced the fuel spring with the blue one shortly after I bought it.
Ford 6.0L Power Stroke Diesel :: Truck Hard To Start / No Power At All
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesFord 6.7L Power Stroke Diesel :: CEL Code P02E1 - Diesel Intake Air Flow Control Performance
My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.
P02E1 - Diesel Intake Air Flow Control Performance
The air box gauge is green and it doesn't reset when I push it so that appears to be fine.
The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.
Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.
I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.
I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.
Ford 6.7L Power Stroke Diesel :: Truck Has No Power Barley Moves / Codes PO113 And PO4DA
OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 RepliesFord 6.7L Power Stroke Diesel :: Reduced Engine Power Message Came Up On Dash And Truck Died
2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
Ford 6.7L Power Stroke Diesel :: Truck Will Rev High In 3rd Gear Then Fall Into 4th / Losing Power For A Split Second
2011 6.7 with 3.55 gearing. Just got the truck. And it seems when its cold the truck will rev high in 3rd gear and then sort of fall into 4th gear sort of losing power for a split second. If I gas it hard, its not as bad. Usually only happens like I said when its cold. Check the trans fluid its full and looks clean. My guess is some sort of sensor or the computer???
View 7 RepliesFord 6.0L Power Stroke Diesel :: Truck Lost Power And RPMs Dropped Only Glow Plug Light Came On
It's a 2004 6.0 excursion with about 190,000 miles. At 185,000 I pulled the motor and did new oem head gaskets, Arp head studs, bulletproof egr cooler and oil cooler system, bulletproof 48v ficm, strictly diesel regulated return, and I've been running gear heads srl tune before and after the truck was rebuilt.
Recently the truck has been acting up at random times. While running the gear head srl tune, the truck will lose power, the boost gauge on my edge insight will get stuck along with Icp psi, the water in fuel light and glow plug light will come on, and then after a few seconds it will clear itself and run fine. Last night I was on a two lane road and putting my foot into it and the truck did the same thing where it loses power, but this time the truck actually died on me while I was cruising at 60.
Same lights were on but this time the cruise control light fluttered while the truck was in the midst of dying. I tried restarting it and it took two sets of cranking before it fired and stayed running. On the way home I babied it and the truck lost power and the Rpms dropped and only the glow plug light came on. Got home and ran codes and I got camshaft and crankshaft position sensor codes and I tuned it back to stock, drove it around, and the truck ran fine, but while on a stock tune I am getting a egr valve code.