Ford 6.7L Power Stroke Diesel :: Truck Has No Power Barley Moves / Codes PO113 And PO4DA
OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Lack Of Power / Truck Will Barely Move And Takes Long Time To Accelerate Under A Load
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Ford 6.0L Power Stroke Diesel :: Overdrive Stumble / Truck Barely Idling When Come To A Stop
So from what I have gathered online, it is an injector(s) issue. I've only had it happen to me twice at that speed but when I came to a stop afterward, my truck was barely idling.
I'm not sure if my sct programmer is able to show injector codes but it will show gp codes. I guess my question is are failing injectors that intermittent typically? Also, much luck with Rev X clearing that issue up?
Ford 6.7L Power Stroke Diesel :: 2012 F250 - Engine Bogging Down
I'm a new Ford owner and my 2012 F250 is my first diesel. Recently, my truck has been having a problem with the engine loosing power, bogging down, shaking-pinging, every once in a while, like 1-2 times a week. When it happens, I can barely get the truck to do 50 MPH. It sometimes happens when the "cleaning exhaust filter" message is displayed, but also happens when it's not displayed. I recently read on the internet about HPFD failures.
What may be happening to my truck? Could it need Cetane booster? Also, how about scheduled maintenance. The owners manual (diesel supplement) says to do the maintenance once the message center says to change oil soon. The dealers here in AZ are pretty much saying 5 months or 7,500 miles. On my other trucks (which were gas), I would stick to what the owner manuals said because I thought how could they deny a warranty claim if you're sticking to what the manual says.
Ford 6.0L Power Stroke Diesel :: Engine Bogging Down / Dying And No Response To Gas Pedal
Recently I have encountered another issue. Truck started up fine, at first stop light and truck was bogging down, RPMs jumping up and down slightly and sounded like it was going to die. Light turned green, gave it gas, no response. Gas pedal was dead. After restarting the truck I was able to give it some gas until I came to the next stop light and this repeated. Eventually a few moments later I got a check engine light. Drove home this way, seemed to be working fine as long as I was actually driving and not stopped.
All the parameters looked ok except for the battery, that jumped up and down in volts as the engine sounded like it was bogging down then eventually died. New batteries put in approx 2 months ago. The check engine light is showing "P0299 turbo/supercharger underboost". I have attached an image of this check engine light according to my monitor.
Ford 7.3L Power Stroke (1999-2003) :: Truck Constantly Bucked And Would Barely Reach 20 MPH
So I have had this occasional hiccup that has gotten more frequent. I figured since our weather has been extra cold (lows about 15 F, around 22 F in the morning), that the temperature had been contributing to the issue. My truck would hiccup and burp out some white smoke. At first it didn't throw a check engine or any codes. As of recently I would get a check engine light, but torque pro could not get any codes, they would be cleared when I cycled the key. Anyways, I finally got some codes yesterday because it happened again. The codes where P0603 and P0344.
So I ordered 2 new CPS from Riffraff yesterday (hoping that they will be here today so I can install one). Fast forward to this morning and i get the hiccup again except worse. Now my truck would barely reach 20mph and it constantly bucked. I limped my way to work (only 4 miles) and of course I got a check engine light but there were no codes that I could retrieve with Torque Pro again. I had read on another thread that the guy had an issue with a wire in the harness near the 42pin connector for the IDM. He replaced his CPS taped up the wire and it went away.
I'm at work and now I'm paranoid that I wont be able to make it home. Is there anything temporary I can do for the CPS, like maybe disconnect it and spray it with some contact cleaner, until I can replace it? I'm going to trace the wire harness to make sure there aren't any bare wires. I forgot to mention that the local stealership replaced the CPS for free due to recall less than 3000 miles ago...
Ford 6.0L Power Stroke Diesel :: Cranking But Barely Tries To Start
Finally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
Ford Ranger / B-Series :: 1988 - Transmission Fluid Leaking Badly / Truck Barely Moves
1988 ranger, its a automatic 4x4 v6 and is leaking tranny fluid real bad. Truck barley moves because fluid comes straight out...
View 1 RepliesFord 6.0L Power Stroke Diesel :: Stuttering On Acceleration / Fuel PSI At Idle Barely Move
I fear my truck may be stuttering on acceleration.
I hooked up a fuel pressure gauge tonight and the fuel PSI at idle and under acceleration... barely moved. Stayed between 60-62PSI.
I'm thinking this isn't normal... shouldn't the PSI be reduced especially when I accelerate hard ?
I'm thinking the "delivery" fuel line... perhaps there is a bottle neck somewhere which is causing constant PSI at the fuel housing ?
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Shaking In Front End When Foot Is Barely On The Gas
I am new to the ford deisel. I have a 2005 F250 6.0 liter power stroke. it has been bullet proofed with EGR delete. Has an after market intake. An Edge TC tuner, and alot of extras. My question is why am I having shaking in the front end when my foot is barely on the gas. If i give it more gas it goes away as soon as the boost kicks up to around 2 or 3. It does this every time I take my foot on and off the pedal. It will only last for a second if i give it alot of gas. But if I barely touch the pedal it will shake the whole time until the boost kicks in.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Hard Steering / Can Barely Turn The Wheel When Stopped
I have an 8 inch lift with 37x13.5 inch tires and dual front steering stabilizers. when I'm stopped I can barely turn the wheel. my buddy has a 6 inch lifted excursion with 35 inch tires in his is easy, one hand no problem. Would the difference in tire size really make that big of a difference or am I having a steering pump issue?
View 9 RepliesFord 6.7L Power Stroke Diesel :: Barely Runs / Misses - Fuel Pouring From Underside Of Motor
So, after sitting for about 4 weeks, I go to start my 2011 F350, 16,000 miles, with a 6.7. Barely runs, "misses", fuel pouring from the underside of the motor, all over the ground. I figure out pretty quickly, #8 fuel injector was blown out of its hole. Clamp is busted.
Two days later (this morning), dealer calls and says we have all the parts we need to fix your truck, except the clamp. Guy says no ETA on the clamp from Ford. Truck will just sit, for an indefinite period of time. Asked him what they were going to do. He said, wait for the part to show up.
Putting aside the oddity of the clamp breaking, how is it that Ford doesn't have the part and doesn't know when it will? Is this a Ford problem or a lazy dealer? This really won't do. Its racing season and I need my truck!
Ford 6.0L Power Stroke Diesel :: Truck Started Chugging Like Going To Die And Had No Power
First post since I bought my powerstroke. I was looking for some diagnostics.
On my way to work this morning and the truck started chugging like it was wanting to die and had no power, the pedal was to the floor and I was barely moving. I was able to nurse it to a parking space at work and pulled the codes, using the Torque pro. This was what I pulled:
P0284 - Cylinder #8 contribution/balance
P0299 - Underboost
P0611 - FICM
P0401 - EGR
P0671 - Cylinder 1 glow plug
On the way home I didn't even hit 5 miles and started into the same symptoms. So I decided to call for a tow, because my commute is about 60 miles one way. In waiting for the tow truck I disconnected the batteries and reconnected them thinking that it might "reset" something. I started it up and the same thing occurred, so I tried revving it up, and starting it up and shutting it down on and off for about an hour. Thinking I picked up some bad fuel. Drove it for a short distance and found things were getting better. I was able to make it home and pulled the codes again. It came up with these:
P0284
P0603 - Internal Control Mod.
P0611
P1000
Also on the ride home I had excessive amounts of black smoke from the exhaust and found a couple of large drops of oil on the driveway where i normally park, larger than what I normally see.
So my question would be what is the cause of all of this?
A little about the truck. it is a F250 CCSB with about 139xxx miles on the clock. I bought it from my brother when he had it he had the FICM replaced (with the 58V option) and the Bullet proof EGR installed. I replaced the fuel spring with the blue one shortly after I bought it.
Ford 6.0L Power Stroke Diesel :: Truck Hard To Start / No Power At All
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesFord 6.7L Power Stroke Diesel :: Getting Code PO088 / Power Reduced When Truck Flashed
I just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 RepliesFord 6.7L Power Stroke Diesel :: Reduced Engine Power Message Came Up On Dash And Truck Died
2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
Ford 6.7L Power Stroke Diesel :: Truck Will Rev High In 3rd Gear Then Fall Into 4th / Losing Power For A Split Second
2011 6.7 with 3.55 gearing. Just got the truck. And it seems when its cold the truck will rev high in 3rd gear and then sort of fall into 4th gear sort of losing power for a split second. If I gas it hard, its not as bad. Usually only happens like I said when its cold. Check the trans fluid its full and looks clean. My guess is some sort of sensor or the computer???
View 7 RepliesFord 6.0L Power Stroke Diesel :: Truck Lost Power And RPMs Dropped Only Glow Plug Light Came On
It's a 2004 6.0 excursion with about 190,000 miles. At 185,000 I pulled the motor and did new oem head gaskets, Arp head studs, bulletproof egr cooler and oil cooler system, bulletproof 48v ficm, strictly diesel regulated return, and I've been running gear heads srl tune before and after the truck was rebuilt.
Recently the truck has been acting up at random times. While running the gear head srl tune, the truck will lose power, the boost gauge on my edge insight will get stuck along with Icp psi, the water in fuel light and glow plug light will come on, and then after a few seconds it will clear itself and run fine. Last night I was on a two lane road and putting my foot into it and the truck did the same thing where it loses power, but this time the truck actually died on me while I was cruising at 60.
Same lights were on but this time the cruise control light fluttered while the truck was in the midst of dying. I tried restarting it and it took two sets of cranking before it fired and stayed running. On the way home I babied it and the truck lost power and the Rpms dropped and only the glow plug light came on. Got home and ran codes and I got camshaft and crankshaft position sensor codes and I tuned it back to stock, drove it around, and the truck ran fine, but while on a stock tune I am getting a egr valve code.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Lost Power When Step On Gas And Truck Wouldn't Exceed 15 Mph
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies