Ford 6.7L Power Stroke Diesel :: Intermittent Squeak / Screech In Steering Column While Driving
So I've begun to notice an annoying intermittent squeak/screech in my steering column while driving, obviously aggravated by the rough roads we've got down here. I can silence it tho, if I push in/up real hard on the steering wheel, so I'm pretty confident there's some bushing or bearing in the steering column that needs some lube or maybe just outright replacement.
View 7 RepliesFord 6.7L Power Stroke Diesel :: 2016 - Rubbing Noise From Brakes After New Wheel?
I had a friend install 18" rims with 35x12.5 tires on my new 2016 F-250 CC SWB that had 18" stock rims. They came off my 2002 Ford 7.3. There is a "creaking" noise coming out of the brake calipers when moving forward slowly with the brakes applied. This never happened with the tires/rims on my 7.3.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Power Steering Lines Has Been Rubbing On Top Of Driver Side Front Shock Mount
Well about 4 days after my HPOP replacement, the ol Ford is at it again. Apparently, one of my power steering lines has been rubbing on the top of my driver side front shock mount. It let loose in a giant black plume of black smoke and grinding gears as I was pulling into the corner store. Limped her home and inspected it. From what I see, its not a terribly expensive hose and shouldn't be too terrible to replace. One thing after the other [URL] .....
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Rubbing Against The Battery Tray?
It appears mine is rubbing against the battery tray in my 04 6.0. It just flops around when I push on it. It's not bolted to anything.
View 8 RepliesFord 6.7L Power Stroke Diesel :: Tailgate Rubbing On Right Quarter Panel
I just identified an annoying squeak as the right side of the tailgate, right at the hinge, rubbing on the section of the rear passenger side quarter panel (one with FX4 decal) where it curls around to the rear. Any way to easily adjust the tailgate slightly to the drivers side? When the tailgate is up, the gap is noticeably smaller on the passenger side, and when down, the edge of the tailgate rubs the edge of the quarter panel, paint to paint.
View 1 RepliesFord 6.7L Power Stroke Diesel :: Squeak In Front Suspension
My new truck has developed a squeak in the front suspension every time you go over little dips and bumps in the road.Which is all the time.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Bang Noise When Speed Up While Driving
While driving I went to speed up and heard a bang. I lost all drive. I have no movement in any gear. I got the truck home and looked around. Trans fluid looked and smelled ok. I couldn't move the rear drive shaft by hand with engine in neutral. I drained the transfer case and that fluid looked fine also. What it could be or what else to look for. The truck is a 2006 f350 with 6.0 and 185,000 miles. Up to this point I had no trans issues.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Rubbing Sound Can Be Heard Through The Turn On Truck
6.0L Forum - I've noticed an unusual sound on my truck. Upon driving if I make a turn more than 15 degrees a "rubbing" sound can be heard through the turn, no "knocking" is not present. Once the steering wheel is straight the sound changes to a "whir". If I turn less than 15 degrees a noticeable sound can not be heard. As the RPM's vary, the sound will also vary. If I get out of the truck and listen for this sound in the engine bay I can not hear it. The sound is only distinct within the cab. It sounds like a weak motor trying to move something or a pump running low, my guess in the dark.
I've checked the oil level - good
I've checked the transmission fluid level - good
I've checked the power steering fluid level - good
I've checked the brake fluid - good
I have read that a master cylinder could wear and create a rubbing/unusual sound. What else should I check for? The truck has 238,000 miles.
Ford 6.7L Power Stroke Diesel :: Wheel Squeak - Brake Warning
Not persistent, but the squeak I had where peeps thought it was the brake warning is back, but not constant.
Seems to happen above 30, and not sure what the other conditions are (maybe hot brakes). but it sounds like only the front right this time.
I've new Rotors and pads. I am on the road right now, been since the 20th and wont be back till the 2nd or 3rd.
Ford 6.7L Power Stroke Diesel :: 2011 F350 - Squeak / Chirp From Front
2011 Ford F350, 69K miles... Just started, at about 30mph. I am hearing a Chirp from the front, speeds up when I speed up and goes away with brakes or slow below 30.
Friend thinks its the brake warning telling me its time for new. Bugging me. Just started. Never changed brakes.
Ford 6.7L Power Stroke Diesel :: 2012 - Squeak In Pillar Between Driver And Passenger Door
My 2012 Ford F350 Super Duty Crew Cab has a squeak in the pillar between the driver and rear door. Or at least that is where it seems to be coming from. It gets better and worse but it's driving me nuts. Any potential fixes?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Squeak / Rattle Type Sound Coming From Front Driver Side Wheel
I'm having a squeak/rattle type sound coming from my front drivers side wheel (more rattle). It only happens when I go over a quick bump and happens going straight and while turning. 2012 f250. 87k miles. 4x4. I have a two inch block level (southern truck) up front..
View 14 RepliesFord 6.0L Power Stroke Diesel :: A/C Leak Found - Rubbing Metal To Metal Caused The Pinhole
Getting the RV ready to go for the summer, and no a/c. I started to add freon, and found the leak right away.
It's on the 3/4" pipe that goes right over the upper radiator hose; obviously rubbing metal to metal caused the pinhole. Now I know where that mystery green snot came from all over my radiator hose coming back from Yellowstone last fall.
First thought was to replace the entire pipe. There's an easy threaded connector on the upper end, but way down on the compressor is a strange fitting that looks like a triangle stuck against a cube. I can't see how I'd get a wrench in there very easy anyway. What is that fitting?
I bought a Dorman 3/4" repair kit, but until it arrives in the mail I don't know if I've got enough straight pipe to work with. Do I need to add oil as well as freon once I charge the system again?
Ford 7.3L Power Stroke (1999-2003) :: Light Metal Rubbing Noise Coming From Front Left Wheel
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
Ford 6.0L Power Stroke Diesel :: Brief Loss Of Power When Accelerate While Driving - Bad Injector?
Occasionally when I'm driving, I'll accelerate and get a brief loss of power, then it'll pick back up, followed by a puff of white/blue smoke. This usually happens when the oil is over 120*, but not quite to full operating temps. It doesn't happen every time either. Only 3 times in the past week. Otherwise, there is a very faint haze of white smoke that seems to be constant. It is very difficult to see unless against a dark background. Oil level is good, I check it once a week, no rising or lowering levels.
I pulled the EGR yesterday, all good, although a tad dirty. Cleaned up no problem. Haven't had a chance to do a bubble test yet. There are some DTCs, but I can't remember off the top of my head what they were. I'm about to go clean the inside of the truck, so I will pull those and update in a few minutes.
Truck has about 148,500 miles.
Torque Pro lists these codes: C1145, P0299, P0677
Ford 6.0L Power Stroke Diesel :: No Power - Only Accelerate At One Constant Speed While Driving?
My f350 6.0 has seem to have lost its power, while I was driving home it would only accelerate at one constant speed, and driving up hill it would not accelerate at all, I also noticed an elevated exhaust temperature.. There are no warning lights or dash lights indicating any problem.....
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Hesitates / Low Power Driving / Idle
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
Ford 6.7L Power Stroke Diesel :: No Power When Accelerate Quickly While Driving - Low Boost Until Restart
I was driving and went to accelerate quickly and had no power, checked the boost gauge and it had very low boost. Continued like this the rest of the drive, all gauges normal, no check engine light, not towing or hot. Got home then next time out it was back to normal.
Someting to be concerned about? Or just a computer hiccup. Truck is '13 with 66k.
Ford 6.0L Power Stroke Diesel :: 2005 - Engine Lost Power When Driving Down The Road
My uncle bought an '05 that stopped running one day. He was driving down the road and engine lost power. He was able to coast into his driveway. Unfortunately, it's been 10 years since I've work on a 6.0 and no longer have any of my computers.
He did state there is no check engine light. He's going to change the filters today / tomorrow. I'm hoping to make it down there this weekend to look at it, but what to look for. Even more unfortunately, we really don't have any specialty tools or gauges.