Ford 6.7L Power Stroke Diesel :: 2013 - Install Flashing LED Lights To Work In Conjunction With Hazard Lights?
I have a 2013 6.7l super duty Lariat. I want to install flashing LED lights to work in conjunction with the hazard lights. The leds have their own controller and will be separate from any other lights/wiring. What I need is some way to trigger a relay to turn on the led's. Was hoping to tap into the hot lead off the hazard switch itself but that's not an option!
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Will Not Restart If Shut Off After Getting Up To Temperature
I have a 2004 f350 6.0 and it makes 550 horsepower and lately when I go to started in the morning it'll start at once everything gets up to temperature if I shut it off it will not start again without starting fluid into the air box if it's warm...
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2013 - CEL Won't Shut Off With 2 Codes?
Alright so I'm a little frustrated at my truck for the last month. I have a 2013 f350 with 2 codes comming up. P0100-mass or volume air flow circuit and a U0106-lost communication with glow plug control module. I have an H&S tuner with the delete. I changed the MAS and it's still lighting up. The dealer is looking into it cause they didn't foresee any problems with the glow plugs either. I erase the code, shut the truck off and once I start it it's right back on! Frustrating!
View 14 RepliesFord 6.0L Power Stroke Diesel :: Non Flashing Wrench Light On Dash
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
Ford 6.0L Power Stroke Diesel :: Gage Fault And Tow Haul Flashing On Dash?
Have a Gage fault and tow haul flashing on the dash have no clue what is going on?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: E350 Lost Power / Shut Down And Won't Restart
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
Ford 7.3L Power Stroke (1999-2003) :: F250 Shut Off And Does Not Want To Restart
Truck is an early 1999 F250 Super Duty ext cab long bed, ZF6 swap. 164k miles on the dash, has the newer injectors and hpop from what I was told. It does have a 6 position switch, I typically keep it at the daily 70 horse gain tune. I do not beat the truck often. I don't tow often either.
Truck always took a few seconds longer to start than other 7.3s I have seen. So two days in row, after 8 hours of sitting in the sun, my truck did not wanna start right. Took about 5 minutes of cranking both days to get it to start. Then today on my way to work in the morning I started truck let it idle, everything seemed fine, Started driving and the engine just didn't sound right, but I figured maybe it was still a little cold. Continued driving, and it stalled out ( zf6) , I tried pop starting it but that only got me another block or two, after 10 minutes of cranking I got it to start up made it a half mile it shut off, same thing started and got it home. It cranked longer than normal but started at home after it I turned it off.
At work now so I have yet to check anything. Replacing CPS after work No smoke out of tailpipe, It is getting fuel, I checked the filter. I am no master mechanic, I do basic maintenance like oil changes, brakes, filters and censors my self. Anything more intensive I have not done. If it is not the CPS what else could it be, and how would I go about checking?
Ford 6.7L Power Stroke Diesel :: Dash Lights Don't Stay On All The Time
I painted the senser on the dash black on the inside so the headlights stay on all the time. My question is the dash lights don't stay on all the time, I assumed they would with the headlights on and senser cover painted, drives me nuts with the dash lights coming on and off. How to make dash lights stay on.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Multiple Lights Won't Showing On Dash?
I have a 2006 F250 6.0 Powerstroke which i bought in May (My first truck and also my first diesel) that I am trying to diagnose a couple problems before it gets into the colder weather. One problem being that my glow plug/WTS light does not come on. What is the possible cause for this? My glow plugs and GPCM all work fine so if there's a bulb that would be out or where the problem would be? I'd like to have this light working before winter time for obvious reasons... and another light that doesn't work that I'd like to try and figure out is the brake light that should come on when you put on your emergency brake.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On Initially / Click Under Dash And Cab Lights Go Off
2006 F-250 6.0l,Auto, 175,xxx mi
When I turn the key to on, I hear the vacuum pump cycle (passenger side fender), but don't hear the glow plugs or injectors cycle. Glow plug light comes on and stays on for 30secs. Wrench light comes on initially, but goes off after 3 secs, but then comes back on after about 8-10 seconds. When the wrench light comes on, I hear a click under the dash and my cab lights go off.
When I turn the key to start, nothing happens. If I jump the starter, engine turns over, but doesn't start. I have check numerous fuses, disconnected the fan clutch, tried moving the shifting lever to neutral, wiggled wires around the FICM/PCM/GPCM with no success.
I tried checking for DTC codes, but my scanner (300 reader) doesn't get any power. I have checked my light, it has power.
Twice before, the truck failed to start like this, but after removing & inspecting fuses/relays (all were good), it started back up. Also, occasionally the truck would stall, (just like someone turned the key off), but would start right backup. But when it stalled, the glow plug light would illuminate for a second,then go off.
Own truck for 8 months, replaced the batteries & injectors 6 months ago. Very light puff of smoke when starting up otherwise ran well when shut off.
How to proceed? My first diesel so I may need some extra details.
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Lost Power Then Stalled And Would Not Restart
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
Ford 6.7L Power Stroke Diesel :: No Power When Accelerate Quickly While Driving - Low Boost Until Restart
I was driving and went to accelerate quickly and had no power, checked the boost gauge and it had very low boost. Continued like this the rest of the drive, all gauges normal, no check engine light, not towing or hot. Got home then next time out it was back to normal.
Someting to be concerned about? Or just a computer hiccup. Truck is '13 with 66k.
Ford 6.0L Power Stroke Diesel :: 2007 F350 - Power Loss After 10 Miles And Dies But Will Restart?
I have a 2007 F350 6.0 Diesel. Truck starts and runs great for about 10 miles and then loses power and slows down til it dies, it does this without any kind of warning and does not rattle or anything. If i let it sit for about 15 min it will start right up and drive fine for another 10 miles or so and do the same thing.
It did the same thing in December but would not restart at all and the ficm was the cause at that time so i went ahead and replaced the ficm just to eliminate it. I also replaced the fuel pump and the ipr and icp valves are good. The only engine code has to do with the fuel level sensor and that has been on for a year. The egr was recently replaced, the hpop is putting out the psi that it is supposed to and there are not any internal air leaks.
Ford 6.0L Power Stroke Diesel :: Won't Restart FICM Drops To 0?
This is the second time this has happened to me . Truck runs fine shut it off go to re start and it's a no start. I can watch the ficm volts drop to 0 from 48.5. Then it's 0 until it decides it gets power again?
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 - No Hot Restart / Now No Start
04 Excursion with 03 motor. I had been getting a no hot restart problem. Now it won't start at all.
FICM 48
rpm around 155-175
ipr goes to 77
icp jumps to 475 and drops back to 400-425
My problem started in Virginia, so I got it started cold and drove all the way home to Indiana without shutting it off. Pretty much been parked since. I've driven it 4-5 times. Now it won't start at all.
I have some LPO problem: I posted it November 2013 [URL] ....
After that I replaced LPO regulator, front cover gasket set, LPO cover (Ford tech said my gearator was fine). I don't think this problem is fixed still
We tried to do a leak down air test. Honestly couldn't hear much of a difference with IPR on vs off. Pulled IPR, found the screen in tact but the plastic pieces that hold it on were all rotted away and broken. I replaced with a brand new IPR to be safe.
I'm not real sure what to look into next. Right now I have both valve covers off and tried to look for a HPO leak in valve covers while cranking. I don't see any oil anywhere coming into the valve train. Shouldn't there be LPO somewhere?
My oil is old now but it was T6 and brand new when this problem first occured. Motorcraft filter but the cap is river city diesel billet cap [URL] ....
Could it be as simple as the oil screen to the HPOP or the check ball in the pump? Can the LPO gauge dropping be related to the no start now? Are there any techs that live in Southern Indiana and want to make some side cash? Last thing I want to do is bring this to the local shop or even worse the dealer. Last time the dealer said they wouldn't touch it because the tuner and EGR delete and the local shop left it sitting for a month and hadn't even touched it.
Ford 6.0L Power Stroke Diesel :: 2005 6.0 Died And Won't Restart
So... Tonight I had just stopped at the bank to deposit a check, hopped in the truck and started her up (started great with no problem), drove the truck through the shopping center and was about to turn on the main road when she died. I coasted into a parking spot and tried to restart her... But all I get is cranking, no firing up or any signs of trying to fire up. Any thoughts?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Died While Driving - Won't Restart
My Brothers truck died while driving and won't restart. I am going to be getting IDS on it tomorrow night and just wanted some feedback on things to watch. I am planning to watch FICM sync, ICP pressure, IPR %, FICM voltage, and fuel pressure(not in IDS). Anything else I should watch while testing?
Edit: this truck is a 2005
Ford 6.0L Power Stroke Diesel :: 2006 - Stalls When Warm Then Restart
My 6.0 stalls when its warm and it restarts no problem. no codes are given with scan gauge. No changes on icp or ipr when it happens. At idle icp ranges 577 to 737, fmp 47.5 to 48v, ipr 23 to 28, map 14.9, tfc .32. all at idle. all increase when rpm goes up. ive done the d plugs, sct plug ficm replaced 2 yrs ago. done egr delete, need to trouble shoot? Again no codes given...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Power Stroke Malfunction - In Reverse / With Lights On Engine Shut Off
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.