Ford 6.0L Power Stroke Diesel :: Non Flashing Wrench Light On Dash
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
Ford 6.0L Power Stroke Diesel :: Wrench Light Came On
This morning on my 15 min drive to work my wrench light came on. i don't get over 30mph the whole time. I tired to get the code before i shut the truck off with my sct livewire but it showed no codes with the light on. It didn't drive any different no loss of power. When i checked memory codes with our shops modis scanner nothing unusual came up besides the fuel circuit fault, which i know about the gauge cluster needs repaired every now and then i cant listen to the radio or roll down the windows.
All my numbers on my livewire looked normal. This is the first time it's come on since ive had the over boost issue fixed. What it could be. Kinda of a kick in the pants after i just saved myself a few hundred on wheel bearings and ball joints. Had a grinding noise at different speeds. Couldn't find anything lose on the front end but still had a grinding noise. Ended up being the exhaust shifted and was rubbing up against the frame.
Ford 6.0L Power Stroke Diesel :: EGR Failure - Wrench Light Comes On
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On But No Codes
Today on the way home after about 45 min drive my wrench light came on but when I checked for codes on my sct I get no codes. Is that weird or common?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Wrench Indicator Light Comes On Every So Often
6.0l oil cooler going - My wrench indicator light comes on every so often so I after about 40 min of highway driving. So I figured my oil cooler might be going out so here are my temps ....
View 8 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On - Small Oil Leak
I have a problem when I have been on the road for about an hour or more the wrench light comes on. There is no change in how the truck runs, and when I run a systems check it says that all of my temps are good to go. The one think I have noticed that the next morning I have a small oil leak on the ground on the days that the wrench has come on. The egr valve was just cleaned. I am getting ready to make a trip across the country with a 10,000 lb trailer so I am a little worried about this. Can I take it in to a shop and have them get a code when the light isn't on? Also I am replacing all of the glow plugs this weekend but from what I have read it shouldn't have anything to do with the wrench light.
View 9 RepliesFord 6.0L Power Stroke Diesel :: No Response When Hit The Gas Pedal / Wrench Light Came On
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On Pulling Even A Light Load Up A Grade
The thing is the truck seems to run fine. But, when it hits 30 pounds of boost it goes in to limp mode. Good way to get yourself run over on a highway. I'm wondering if the computer or whatever has gotten off somehow and is sensing a problem too early ? Would a re-flash possibly correct this ? BTW, it is a 2005 with 63,000 miles.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Wrench Light Keeps Coming On Mostly When Doing Highway Driving
I have ran 05 f250 and the wrench light keeps coming on mostly when I'm doing highway driving or when I go to pass someone. iv putt code readers on it(autoparts store readers and the good expensive ones)and i keep getting bad egr and some other codes but when I have the truck looked at everything is prefect I had a flush done on the truck and and it still comes on randomly . Could the fact that it needs an oil change cause the light to come on intermittently or is something else going on??
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Wrench Light Came On While Driving On The Highway
2007 f250 6.0 .... I just had the wrench light come on while driving on the hwy. wasn't towing, or hauling anything. Just traveling around 70mph for an hour or so. I didn't notice any change in power. Got to my destination and cut the engine off. Couldn't pull any codes with an OBD II scanner. When I started it up again, light was gone. Owner's manual points to electronic throttle control, not much else.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Size Of Wrench For Battery Terminal?
I'm not near my stuff--is the battery cable terminal bolt 8mm?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Dash Lights Don't Stay On All The Time
I painted the senser on the dash black on the inside so the headlights stay on all the time. My question is the dash lights don't stay on all the time, I assumed they would with the headlights on and senser cover painted, drives me nuts with the dash lights coming on and off. How to make dash lights stay on.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Multiple Lights Won't Showing On Dash?
I have a 2006 F250 6.0 Powerstroke which i bought in May (My first truck and also my first diesel) that I am trying to diagnose a couple problems before it gets into the colder weather. One problem being that my glow plug/WTS light does not come on. What is the possible cause for this? My glow plugs and GPCM all work fine so if there's a bulb that would be out or where the problem would be? I'd like to have this light working before winter time for obvious reasons... and another light that doesn't work that I'd like to try and figure out is the brake light that should come on when you put on your emergency brake.
View 10 RepliesFord 6.7L Power Stroke Diesel :: Wrench Icon Displaying In The Instrument Panel - Communication Codes
Couple of weeks ago, the display in the instrument panel displayed a large orange wrench. No accompanying text or chimes, just the damn wrench. Checked for codes, nothing out of the ordinary (I occasionally get communication codes, but they usually show up when I do not wait to start). Long story short, the damn thing showed up one more time the same day, then never again.
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2013 - Dash Lights Flashing / No Restart After Shut Off
6.7 with 19k . Drove about 2 miles and noticed dash lights were flashing and ac was not working correctly . Pulled into garage shut off and truck wouldn't restart, no crank ! All my dash lights were flashing & dash was giving numerous messages.. At least I wasn't on my road trip 2 weeks ago! 3400 mile round trip. Truck was towed to dealer! My 6.0 never left me stranded & I had 3 of them..
View 14 RepliesFord 6.0L Power Stroke Diesel :: Blue Light On Dash?
Simple question for the group as I learn about my new B.O.A.T 6.0 diesel.
What is that blue light left of the steering column yet on the dash?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - 4x4 Will Not Engage / Lights On Dash Don't Even Light Up
I have a 2002 7.3 4x4 truck. The 4x4 will not engage, the lights on the dash don't even light up. I took it to the ford dealer and they said the fuse box and gem module. (800.00 to fix). They said the windshield leaked and shorted then out, so I needed to be replaced? I have replaced the windshield and fixed the leak, my question is the fuse box and gem a plug and play and do different years work?
View 5 RepliesFord 6.0L Power Stroke Diesel :: When Turn The Key Clicking Under Dash And Cruise Light Flickers
I have been trying to diagnose my truck for 2 weeks now. Truck basically died at light. Towed to a friends shop, had ficm low voltage and crank and cam codes. He replaced crank and cam sensors with aftermarket ones from his parts supplied. I also purchased a ficm, still no start. When i turn key I get a clicking under dash and cruise light flickers, it does flash it flickers. If I unplug ficm relay or icp it will stop and crank over.i am getting a weird random off and on ficm sync.as well as cam crank sync.
If I unplug icp it will start for about 30 seconds then dies and as i am watch ficm and cam sync,when it says no is when it dies. Key on Icp unplugged. Here is Icp plugged in you can see cruise light flickers and check engine goes on and off but this is when it will grind starter. I'm starting to think maybe the motor fires briefly and then dies and starter is trying to engage moving flywheel.
Ford 6.0L Power Stroke Diesel :: Battery Light Lit Up On Dash - Voltage Drop And P0528 DTC
My Battery light came on on my dash and my scangauge 2 was reading 11.5/11.4 volts yesterday afternoon, I ran for codes on my obd-2 and P0528 came up. I picked up one new battery and put that in to see if that would bring my voltage up at all. Today it was reading 11.3/11.2 volts. From what I've gathered the P0528 is most likely the fan clutch or the harness connecting the fan clutch to the PCM.
I've seen the water pump replacement write up that shows how to pull the fan assembly. My questions are - can the fan clutch be replaced without draining/pull the radiator? or is it better off to just do the coolant flush and pull the radiator. And would the fan clutch/harness issue drop the voltage or would that just be two bad batteries?