Ford 6.0L Power Stroke Diesel :: Fan Stays Engaged Until The Truck Hit Operating Temperature
I replaced my fan clutch... Not a bad job, did it a couple weeks ago. I don't drive the truck much, but took it out today for the second time in the two weeks since I replaced it. The fan stays engaged until the truck hit operating temperature it seems. Is that normal?
View 1 RepliesFord 6.0L Power Stroke Diesel :: No Power At Operating Temperature?
This is my wife's daily driver so I've got to get it done this weekend. 05 Excursion with 04 motor, 95,xxx miles. No problems until Friday. My wife drove to Seattle for a physical therapy appointment for my daughter and when leaving she said it felt like it was idling a little weird. She was at a stop light and when it turned green she could barely move, no power. Called me and everything sounded good from the Edge. Had the truck towed from Seattle to our house, about 60 miles. Idles really rough in drive, smooth's out a bit when in neutral. Starts totally fine when cold or hot, but doesn't start acting up until at working temp. When I say there is no power I mean the truck won't even pull up our drive way that only has a slight incline and is the length of the Excursion.
Only code I get is a P1000, but that is always on the tuner for some reason. I pulled the upper fuel filter and I'm getting fuel. Checked all the fittings I can see and nothing electrical seems out of the ordinary. New IPR and ICP within the last year. Tried disconnecting the EGR and it ran the same, but threw a P0403 and P0405 code. I've tried researching this and can't seem to find anything having to do with loss of power when hot. Sitting in the street in front of the house with the truck running I show an ICP of 750psi IPR of 28% @ 680 RPM VGT is 64.6 and MAF is 44.0. I can hear the turbo whistle, but show 0 boost which I think is normal when no load. I tried pulling into the drive when at temp and the truck was hitting 1000 rpm with pedal to the floor and wouldn't move, shaking and rough the entire time. Before all this my delta on EOT and ECT were under 5*
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Poor Acceleration When Engine Is At Operating Temp
I have a 04 f350 6.0 with about 195xxx miles on it. The other day my truck started acting up. It starts and idles without a problem and drives fine till the engine gets to operating temp once there I cannot accelerate quickly like getting onto the highway to get up to speed it just the motor just goes quiet and won't accelerate. It usually does this a little after 2000 rpm. I can let off the throttle and slowly get to speed as long as I don't go past 2000 rpm. No check engine light was not on scanned it and got p0611 for the ficm. I tested the ficm and it read 48v with key on. While truck was running I got 46.xx v then Started to climb to almost 48v. The truck was warm but not at operating temp where the problems starts(didn't have time to let it warm up all the way) could these symptoms be the ficm still? What else should I test?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Take 10 Seconds To Crank At Operating Temperature?
I have a 2000 F250, 300k. Starts beautifully when cold, takes 10 seconds of cranking when at Operating Temperature. Did the injectors and plugs in September, kept doing it and now that it's summer it's getting harder and harder to start. Just replaced the ipr, still doing it. Gonna do an overdue oil change tonight or tomorrow, I'm hopeing that will improve it. I can understand 3 or 4 sec of cranking, but not 10. Truck hads no drivability issues whatsoever. Will an ICP fix it? Change to a heavy-duty 20w-50? (Last oil change was delo 15w-40) The code reader that I have is really basic, and only shows me RPM and map.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2011 - AC Blows Almost Warm When Idling
So, I pretty unimpressed with the air in my 2011 SC 250. I keep the climate at about 69, and seems like is work about half as good as my 2010 F150 with climate did. When idling it blows almost warm, only cools when the RPMs are up there. My F150 seemed to be the same no matter what.
View 14 RepliesCamry :: Hard To Start When Warm At Operating Temperature
My Camry has 185,809 miles on the 4 cylinder, it has recently started to be hard to start when it's at operating temperature, has code P0301 and p0302 replaced spark plugs at 185,000 miles no change, possibly ignition coils?
View 1 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start When Engine Warm
I have recently developed this problem with my 2005 F250 6.0L with 86,000 miles and don't quite understand it. If I drive my truck and then shut it off for a couple minutes, say to go in the store for a few things, when I try to start it back up it won't stay running. It chugs for a couple seconds at real low RPMs (300-400) then just stalls. When I was at the store the first time this happened, I went back in and bought a bottle of starting fluid and gave it a shot, (I know I know, shouldn't do that) and it started right up and got me home.
Thought it was a fluke as the next time I went to start it, it fired right up (sat over night). Drove a couple hours then shut it off, it sat for three or four hours. I went to fire it up to go to a wedding shower down the street about 20 minutes drive and it started fine. Shut it off to go in and pay my "respects" and was out in ten to fifteen minutes. Again Chug, Chug, Chug, stall. Tried to start it with the same results about ten times, then I said fine went back in and ate some free food and drinks for a couple hours and came back out and it fired right up again.
I drove home tonight and while in by drive way at home tonight I verified this again. Turned the truck off and tried to start it back up ten minutes after unloading the truck and same thing, no start. What could be the problem? Only other issue I've noticed was a lack of power on take off from a dead stop then a like a switch the power comes on in about three seconds.
Ford 6.0L Power Stroke Diesel :: 2003 Will Not Restart Again After Engine Gets Warm / Bad HPOP?
2003 with hot no start issues. It starts fine in the morning however will not start again after the engine gets warm, after an hour or so of cooling off it will eventually go. Not sure if I should start with.... Readings below ....
FICM L 13.5v
FICM M 48v koeo and 47 running
IPR 14.7% koeo
IPR 74.6% cranking (no start while hot)
IPR 40% (after cold start while running
ICP 737psi cold start
ICP 1600psi engine running 2k rpm
ICP 360 hot while cranking
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Engine Gets Warm / Hard To Restart
I have s 2007 f250 superduty with a 6.0. Recently after the engine gets warm I have a problem restarting it. I have to turn the key to the run position until all sounds have stopped then I have to pump the accelerator to get it to start. Sometimes I have to repeat this three or four times before it starts. I have had the fuel pump rebuild and installed two new batteries. What I should be looking at.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Engine Idles Rough When Warm - No Codes - Fan Speed 0 Rpm?
Like the title says I'm having an issue the past few days where I can't drive this truck more than a few miles before it starts acting up with rough idle at stoplights/sign and sluggish acceleration until it gets over 1200+rpm.
Cold starts fine, drives good till engine warms up to around 130+ECT then it starts acting up. Stumbles on acceleration for little bit and puts out a little black smoke until it gets moving. No check engine light or codes found.
However a month ago I had the check engine light come on with a P0404 & P0405 and it still started & ran/drove great even towing. If I reset the code it would stay off until I restarted the engine the next time. I replaced the Dorman EGR because it had a lifetime warranty and only had 5,000 miles on the first one. The code did not go away until about two weeks ago the light went off on the dash and has never come back but I had not erased the code? So I'm not sure if this is still lingering issue or what.
I was checking my ScangaugeII when I came back home today while the engine was still idling rough and this what I saw for Numbers:
Low idle in Park
ECT 193
EOT 191
FICM 49.0
IPR 21.4
ICP 582
ICV 0.81
V 13.8
TFC 1.91
VSS(fan speed) 0
(This one doesn't seem right in the past is 500 or more rpm from what I remember?) What am I missing to check over?
Ford 6.0L Power Stroke Diesel :: Black Smoke Only After Up To Operating Temp And EGR Opens
I have replaced the EGR over 1 month ago and also replaced the MAP sensor also as it was bad. I also have a Scan gauge, for monitoring.
The problem is once the truck gets to OT and the valve opens I have heavy black smoke on take off?
Ford 6.0L Power Stroke Diesel :: 2003 - When Engine Get Warm It Starts To Smoke Unburnt Fuel
I have a may 2003 6.0l f350 4x4 ,autoenginuity scanner, recently bought the truck starts fine and idles well then when engine get warm it starts to smoke unburnt fuel (white) volume of fuel desired on scanner goes from about 14 mm~3 to 27mm~3 and starts to run rough if you depress the acellerator the motor smooths out and the fuel desired goes down. No coolant smell. egr cooler removed ,oil cooler replaced, exhaust back pressure sensor and tube cleaned .ebp sensor koeo 14.2, eo 17 but jumped to 54.0 when map was at 17, bp 31.20 .... The AE is new to me Also found a superchip tuner under the back seat ...
View 14 RepliesFord 6.0L Power Stroke Diesel :: Smoke From Tail Pipe - Haze At Idle When Engine Is Warm
Have a lot more smoke from the tail pipe when they are running their tow tune vs their street tune? For me it seems like a lot especially right now being cold out but I still notice a haze at idle when the engine is warm. Also can smell a difference.
Getting a ficm tuner from php tomorrow so interested to see what that does for things.
Ford 6.0L Power Stroke Diesel :: AC Blow Cold For 10 Minutes Until Everything Is Up To Normal Operating Temp
When I fire her up, the AC will blow cold for 10ish minutes until everything is up to normal operating temperature. Then it tends to blow warm, and that last for about 20 minutes, before finally settling back down and being cold AC again. I initially thought it was an issue with my compressor disengaging, but it doesn't seem to be...
View 3 RepliesFord 6.0L Power Stroke Diesel :: P2290 Code - Chugging At Operating Temp And Sometimes Even Die While Driving
I have a 2007 F250 6.0 L with 116000 miles. I have never done any modifications or changed anything on the truck. Now that the weather is starting to warm up I've noticed that once the truck is at operating temperature it starts to chug and sometimes even die while driving and while its doing this the truck has no power. It does not seem to do it when its cold. Here is a picture of my gauges KOEO operating temp at idle...
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - Truck Not Starting When At Operating Temp
The other day, I started having problems with the truck not starting when at operating temp. Went for a drive and stopped a a scenic overlook, and spent about 30 minutes taking pictures. Went back to the truck, and it wouldn't start. Outside temp was about 95 degrees.
I tried for about half an hour to start it, but all it would do is turn over. There was a work crew there with their heavy machinery, and I was able to borrow their starting fluid. One quick squirt into the intake, and it fired right up.
Although I do have an oil leak from the right valve cover, when I checked the oil, it was just off the full mark. The truck was parked on a slight angle with the driver side being about a foot higher than the passenger side.
2003 F350 w/6.0, 180,000 miles
Ford Ranger / B-Series :: 1997 - Engine Will Not Reach Proper Operating Temperature
I have a 97 Ranger 2.3 standard shift, No A/C, a pretty simple Ranger with 158,000 miles. About a month ago while do some checking around under the hood I noticed my coolant overflow tank was empty, so I filled it up to the proper level with some anti-freeze mixture. Thinking if the system was low on anti-freeze it would suck what it needed from the recovery tank, wrong! About two weeks ago I noticed that my temperature gauge was NOT registering in its normal position and was considerably lower towards the Cold mark. Heat coming out of the heater was normal.
I opened the radiator cap and everything looked okay. After a few days this would not go away and replaced the thermostat thinking the thermostat was stuck in the open position, wrong again! I burped the system by letting the engine run with the radiator cap off and filled the radiator with anti-freeze mixture every time some of the air was expelled. I did this for a few days and noticed that the engine would not reach normal operating temperature at idle speed! I had to put something on the gas pedal to increase idle speed so the engine would get hot, this is not normal. Finally I got to a point where the radiator would not take anymore anti-freeze mixture, but the problem still exists.
Two things I noticed that will get the engine temperature up to normal, engine speed (RPM's) and not having the heater on. Let me explain, at normal idle the engine will not reach its proper temperature, but when driving down the highway the temperature goes up to normal (about halfway on the scale) no matter if the heat is on or not. When stopped at a light or just idling I can watch the gauge slowly go down towards the cold mark, if I turn off the heater it takes longer to go down to cold. I do know the heater fan is cooling the coolant to a degree (no pun intended), but it shouldn't cool it so much as to make the temperature drop so dramatically. Okay, heater off, riding down the highway, everything normal, come to a stop and idle temperature starts falling slowly, but when I turn on the heater the temperature starts falling faster.
My diagnosis: I have no leaks of anti-freeze, checked and re-checked. I have no symptoms of a blown head gasket, no milky white appearance on dip stick indicating anti-freeze mixing with engine oil, no clouds of white smoke coming out of exhaust, checked tail pipe for anti-freeze, none found, no loss of power and no loss of gas mileage. I changed the thermostat, like I said. Do not think it could be the radiator pressure cap, normally if the cap goes bad the system will have no pressure and the engine will overheat, the opposite of the problem. Water pump, normally if the water pumps goes the coolant will not circulate through engine and will over heat, again, not the problem I am having. Could it be:
1. A long shot, I bought a defective thermostat and it is still staying open.
2. The temperature sending unit has gone bad, very improbable since it does register the correct temperature when truck is moving down the highway.
3. The coolant is spent, again unlikely, it has been in the engine only for about 3 years and still looks clean and green.
4. Have to have a cylinder pressure check to determine actually if the head gasket is really blown or not, which I doubt.
My conclusion is that I still have a huge air lock somewhere in the system and the engine is still not completely filled with coolant and when the rpm's drop not enough hot coolant is reaching the temperature gauge sending unit, but if that much coolant is not in the system, why am I still getting lots of heat blowing from the heater? The vehicles cooling system is not that complicated and there are few parts involved in its proper operation, I think I have covered them all, but somewhere I am missing something to pin point my problem.
Ford 6.7L Power Stroke Diesel :: 2011 F250 Won't Start After Getting Reduced Engine Power Message
I have a 2011 Ford F250 6.7 Powerstroke. It has 107,000 miles on it.
The other day I was driving it down the highway and it got a Reduced Engine Power message on the dash. It lost power and I got off the highway to the service road. Then it died on me.
Had to get it pushed to a station then towed home. It wouldn't start. The starter cranks over for a few seconds but engine won't start. Checked all the fluid levels and batteries. My DEF fluid was only a half gallon low.
What I have noticed is that the DEF level indicator hasn't reminded me that it was low for over 4-5 months now. I had been putting in about 2-3 gallons every 3 months or so. But it hasn't reminded me lately and I just forgot. This is my first diesel.
Ford 6.7L Power Stroke Diesel :: 2011 F250 Crank But No Start / Reducing Engine Power
My 2011 6.7L F250 Superduty died on interstate the other night. Picking up throttle pulling onto interstate when a message came on the dash "reducing engine power" and the truck died. It will crank but will not start. It will start on ether but dies when that runs out. Has the following codes... p1249 Wastegate control valve, p0087 fuel rail/system pressure too low, p1291 & p1292 injector high side short to ground or battery (bank 1 & 2), p2291 injector control pressure too low-engine cranking. The codes are telling me I don't have enough fuel pressure but scan tool says I have 4000 w/ key on and 6370 while cranking and I thought 5000 was the pressure needed.
View 9 Replies