Ford 6.0L Power Stroke Diesel :: 2004 F350 - Poor Acceleration When Engine Is At Operating Temp
I have a 04 f350 6.0 with about 195xxx miles on it. The other day my truck started acting up. It starts and idles without a problem and drives fine till the engine gets to operating temp once there I cannot accelerate quickly like getting onto the highway to get up to speed it just the motor just goes quiet and won't accelerate. It usually does this a little after 2000 rpm. I can let off the throttle and slowly get to speed as long as I don't go past 2000 rpm. No check engine light was not on scanned it and got p0611 for the ficm. I tested the ficm and it read 48v with key on. While truck was running I got 46.xx v then Started to climb to almost 48v. The truck was warm but not at operating temp where the problems starts(didn't have time to let it warm up all the way) could these symptoms be the ficm still? What else should I test?
View 5 RepliesFord 6.0L Power Stroke Diesel :: Black Smoke Only After Up To Operating Temp And EGR Opens
I have replaced the EGR over 1 month ago and also replaced the MAP sensor also as it was bad. I also have a Scan gauge, for monitoring.
The problem is once the truck gets to OT and the valve opens I have heavy black smoke on take off?
Ford 6.0L Power Stroke Diesel :: AC Blow Cold For 10 Minutes Until Everything Is Up To Normal Operating Temp
When I fire her up, the AC will blow cold for 10ish minutes until everything is up to normal operating temperature. Then it tends to blow warm, and that last for about 20 minutes, before finally settling back down and being cold AC again. I initially thought it was an issue with my compressor disengaging, but it doesn't seem to be...
View 3 RepliesFord 6.0L Power Stroke Diesel :: P2290 Code - Chugging At Operating Temp And Sometimes Even Die While Driving
I have a 2007 F250 6.0 L with 116000 miles. I have never done any modifications or changed anything on the truck. Now that the weather is starting to warm up I've noticed that once the truck is at operating temperature it starts to chug and sometimes even die while driving and while its doing this the truck has no power. It does not seem to do it when its cold. Here is a picture of my gauges KOEO operating temp at idle...
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 Starting Loosing Power / Wouldn't Even Go Up To 15 Mph
I have a 2003 Ford F-350 super duty 6.0. A few weeks ago it starting loosing power, it wouldn't even go up to 15 mph. It now won't even move. There is 0 power. When I press the gas the motor bogs down to a very low idle and wants to die. I also had recent trouble with it starting. It would wind up to a very very low idle and about a minute later it would crank up to full idle. I changed the fuel filters (on top of the engine and under the cab) and also changed the fuel pump under the cab. After that I still have no power when pressing the gas it will still act like it wants to die.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Fan Stays Engaged Until The Truck Hit Operating Temperature
I replaced my fan clutch... Not a bad job, did it a couple weeks ago. I don't drive the truck much, but took it out today for the second time in the two weeks since I replaced it. The fan stays engaged until the truck hit operating temperature it seems. Is that normal?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 Truck Revving Up Out Of No Where
So I'm having a problem with my truck revving up out of no where. Happens more when I'm driving. It only shoots up a little bit but sometimes goes up 1000 more rmps. Happens for a quick second then stops and does it again. I've had the ckp replaced and it has an egr delete. Other than that it's stock. I got home and let it idle for a minute. The rpms fluttered up and down in small increments and almost stalled out. What is causing this?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - ICP Defaulting To 875 PSI When Gets To Temp
I had this issue a few years back, but the problem disappeared. You can read about it at this link. Now the problem is back.
[URL] ...
2005 F350 6.0
New International ICP (two weeks old)
New pigtail
Truck starts and runs fine. When it gets up to temp, usually about 20 minutes into my 40 minute commute, the ICP psi at idle will go to 875 psi, steady. I believe the pcm is defaulting to 875 at idle. I still get a ICV reading (changing with RPMs) when in this condition. After driving like this for about 10 more minutes, the wrench light comes on and I throw code 2286 High ICP.
I have found a couple places in the wiring harness under the turbo where wiring got hot and melted the wires. I removed the portion that was melted and soldered in new wiring. Problem remains.
Here are a couple snapshots of scanguage II, one at idle and one at koeo. I still think I have an intermittent open in my wiring harness.
Ford 6.0L Power Stroke Diesel :: Oil Temp Sensor Goes Right To Half Way When Truck Turned On?
Oil temp sensor - when I turn the truck on - it goes right to half way. I am guessing it is broken ? But then again, if it was broken, why would it go half way ?
View 5 RepliesFord 6.0L Power Stroke Diesel :: Truck Is Starting To Surge A Bit Like ICP Sensor Going Bad
I started having an issue with a rough idle soon after startup about a month ago. I thought it might have been stiction so I added some Archoil stuff the other day to my oil interval change and although I have not put too many miles on it, the rough idle is still there.
At startup the engine runs great. I did notice a few times a little longer than normal crank (~3 seconds) where other times it fires up in less than 1 second. This has happened twice in the last month. Once the engine runs for about a minute I get an uneven idle......I wouldnt necessarily call it a miss per say. I took some readings for the ICP and IPR and can provide them if someone needs them. Once the truck warms up it seems to idle better but still not 100%. I have no power loss, no hesitations jut a weird idle with intermittent surging while in gear.
The truck is starting to surge a bit like an ICP sensor going bad but not as pronounced as the last time this happened to me 4 years ago. Basically trying to get opinions as to what it might be or what to check next. I am leaning toward one of three things.....stiction, ICP or IPR valve (original). FICM voltage is good but my fuel pressure gauge broke, but the blue spring upgrade I did.
Ford 6.0L Power Stroke Diesel :: Truck Would Die After Starting Then Start Up Again After A Minute
2004 6.0 Diesel. First the truck would die after starting, then start up again after a minute. Then the truck wouldn't start at all.
Trouble codes indicated low voltage on all injectors leading me to conclude a dead FICM. Replaced the power module in the FICM and reinstalled, but still no start.
48V at driver's side screw under the cover. 12V at the next screw, the next appears to be ground. The passenger side screw is 0V. One post indicated that should also be 48V - is the true?
I probed the power coming in - logic fuse is good. 50A fuse in the cab is good. Relay seems good.
The Ford FICM diagnostic indicates 12V power should be coming in on FICM connector X3 on pins 7, 8, 4, 23, 24, 25. I have 12V only on pins 7, 9, and 27. When I pull the relay I lose power on pin 27.
Ford 6.0L Power Stroke Diesel :: Truck Dies Within A Minute After Starting
Parked the truck last night and all was fine. Went to start the truck today and let it warm up before hooking up the trailer and it dies withing a minute. Go to start it again and nothing. End up killing batteries. Checked for codes and had a bogus EGR code P0404. Bogus because the tune I run doesn't have the EGR enabled and it is deleted. Still plugged in though.
Hooked up dual battery chargers and sent the boy to pick up fuel and oil filters and oil. It was over due in both areas. Changed both and still no love. So I drag out the laptop and set up my AE to monitor FLP, FLM, IPR, ICP, ICV, Sync.
KOEO
FLP 11.00
FLM 47.0
ICP 0
ICV .24
IPR 14.25 odd right?
Synch 0
Cranking
FLP 9.6
FLM 47.0
ICP 800-1600 varied the longer I cranked
ICV 2.2
IPR 14.24
Synch 1
still no start.
Still no codes.
I then cycled the IPR through AE a few times and turned the key. Damn thing fired right up.
Idling
FLP 11.0
FLM 47.0
ICP 875
ICV 1.4ish
IPR 26.4
Synch 1
I pushed the RPMs up to 2500
FLP 11.0
FLM 47.0
ICP 2200 iirc
ICV 2.24
IPR 42.0ish
Synch 1
Turned the truck off and restarted it a few times. No issues. Turned it off and pulled the positive cables and put the chargers back on it.
So the question is .....Is the IPR sticking on me? I just replaced the HPOP in the spring along with the up pipes. Made sure everything was clean. I actuated the IPR and cleaned it out. Put a new screen on it had zero leaks.
Ford 6.7L Power Stroke Diesel :: F350 - Truck Shut Down While Going At About 25 MPH
I am getting ready to go on vacation this weekend with my f350 and I was driving today when suddenly the truck shut down while going at about 25 mph. I tried to start it and it just kept cranking. I got it started 5 mins later and it threw a P0069 code. I drove for about 2 more miles and it shut down again, and started right back up. I'm guessing map sensor? This was the last thing I needed to happen!
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 Not Starting / No FICM Sync
I have a 2006 F350 with around 208k mikes, automatic with a no start, 0 No FICM Sync.
The CMP and CKP has "no / 0" for synchronization and a "NO" synchronization from the FICM. Should this be "yes / 1" when trying to start?
The camshaft position sensor status indicated "yes fault".
FICM is at 48V,
DTC currently on
P2614 camshaft position signal output/open circuit - CMP
Glow plug circuit cylinder 2, 4, 5, 6 (these have been on for 12months and 1,000 miles and never had an issue starting)
B1352 - left front temperature damper motor
B1360 - left rear temperature damper motor
U1900 - CAN - communication BUS fault
I am running all OEM filters
Ford 6.0L Power Stroke Diesel :: 2007 F350 - Driveline Vibration Starting At About 45 Mph
Truck is an '07 F350 Supercrew, 8ft bed, SRW, 2wd. I bought the truck last month and noticed a low frequency driveline vibration starting at about 45 mph and is noticeable to about 65 mph. Feels like a bad u-joint. So I pulled the drive shaft (two piece) and checked the joints. They seemed find so I sent it to a commercial truck shop that does driveshaft work. Had the joints replaced and the shaft rebalanced.
Re-installed drive shaft and went for a test drive. No real change in the vibration. The hangar bearing seemed fine so it wasn't changed. Doesn't feel like a wheel out of balance. My experience tells me its a drive shaft.
Ford 6.0L Power Stroke Diesel :: 2007 F350 - Crank For About 3 Seconds When Starting
2007 350 the truck sat overnight (15 hrs) I went to start the truck and it had to crank for about 3 seconds which is abnormal for my truck?? It was about 80 degrees outside. Is there any reason for that?
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Truck Will Not Start
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
Ford 6.0L Power Stroke Diesel :: 2005 F350 - GPCM Getting Hot With Truck Off
I've got a problem with an '05 f-350 with the 6.0. Initially I had a code for the #1 glow plug so I replaced the plug and the code was still there. Next I tested the harness and the rest of the plugs on the same harness and everything checked out fine. This lead me to the Gpcm which I then replaced. The first thing I noticed was when removing the old Gpcm I got a spark when removing the mounting nuts.
When I installed the new Gpcm the truck started fine and no codes came up so I thought all was good till I went to start the truck the next day and the batteries were dead. I thought I possibly left something on so i started charging the batteries but noticed they seemed to have a draw on them. I put my hand on the new Gpcm and it was very warm with the key off so I have the batteries disconnected till I can figure this out.
Ford 6.0L Power Stroke Diesel :: 2007 F350 Not Starting - Running Rough - FICM?
I just bought a 2007 F350 6.0 two days ago, so I was giving the truck a good wash today using a electric pressure washer. The engine bay was pretty dirty so I decided to take some soap and a brush to it. After cleaning it I let it sit for a while in the sun to dry. (engine was stone cold). After it had completely dried out I go in and it cranked right up. I let it idle for a good minute-minute and a half put it in drive and pulled away slowly, right when I touched the accelerator it started running rough, so I popped it into neutral and let it idle for a sec but it was still running really rough so I cut it off not wanting to damage anything worse.
I let it sit and tried to start it again, it just turned over and over. I checked the oil level it was good. So I pushed it back into my driveway to figure it out. I took ICP connector out and tried to start it, just turned over and over. took fuel filter out it was just replaced 2K miles ago it looked a little dirty but not super bad. I put that back in. took icp out again and tried to start it and it started but ran super rough and was dumping black smoke out.
I checked back all ficm connectors and they were all connected. I haven't checked the voltage on that yet, but plan to do that tomorrow. the previous owner had the ficm go bag about a year ago and he sent it off to ficmrepair.com and they fixed it for him. also he had the stand pipes and dumby plugs done as well as the stc on hpop. im kinda at a loss on where to go now other than to check voltage on ficm.