Ford 6.7L Power Stroke Diesel :: 2011 F250 Won't Start After Getting Reduced Engine Power Message
I have a 2011 Ford F250 6.7 Powerstroke. It has 107,000 miles on it.
The other day I was driving it down the highway and it got a Reduced Engine Power message on the dash. It lost power and I got off the highway to the service road. Then it died on me.
Had to get it pushed to a station then towed home. It wouldn't start. The starter cranks over for a few seconds but engine won't start. Checked all the fluid levels and batteries. My DEF fluid was only a half gallon low.
What I have noticed is that the DEF level indicator hasn't reminded me that it was low for over 4-5 months now. I had been putting in about 2-3 gallons every 3 months or so. But it hasn't reminded me lately and I just forgot. This is my first diesel.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Engine Change Out Now The Truck Will Not Start On Hot Crank
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Crank But No Start
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - No Crank No Start
I have a 2006 F250 6.0 with 218xxx on it. Have had a ton of issues since day one, but I finally thought I had gotten a handle on all of them until the other day. Truck started sounding a little rough, no noticeable effect on performance, no codes on my Edge CTS (except one random CKP sensor code that went away). Was leaving work later that day to go home and it started up fine.
Got about a 1/4 mile from the shop and went to turn onto a busier road so I put into the pedal a little bit. Truck immediately lost power. Sounded like a turbo boot blowing and I had very little throttle response. Immediately pulled over and checked codes with truck still on, nothing. Got out and popped the hood with the truck still idling to check for CAC tube/boot etc. As I was looking at it, the engine started screeching. I shut it off as quick as I could get back to the cab.
Looked over everything, nothing noticeably wrong. Went to crank it to see what it would do. All i got was a noise from the starter engaging. Belt not turning over. Tried unplugging the fan clutch (read a thread with similar symptoms and that was the issue for them), connected the starter solenoid directly to battery, same issue. Removed belt and attempted to crank. Same thing. Removed all glow plugs to check for hydrolock. Motor slowly would turn with belt still removed and no glowplugs. Removed starter and tested outside of vehicle, solenoid and motor both seem to be ok.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Crank But Won't Start
I have a 06 6.0 f-250 it cranks but won't start untill I pull the secondary fuel filter cap off and seems to vent air in the system out then it starts right up. I can't figure out where it's sucking air. Here's my question I changed the fuel sending unit in the tank a few weeks ago and had a hard time seating the lid on top of fuel tank. If it is not completely seated will this cause air in the fuel system and give me the headache I've been dealing with?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Sputtering / Crank No Start
2005 Ford F250 6.0 Diesel (bought new). Never had a problem with the engine until about a month ago. Engine has 220,000 miles on it. Oil and filters changed regularly. Ran low (not out) of fuel, started sputtering badly but not killing. Filled up with diesel. Ran better, managed to get home. The next day it was dead. Crank but no start. Since then I have done the following (not in order):
- Changed EGR
- Changed ICP
- Changed IPR
- Changed the STC fitting
- Changed all seals in the HPOP
- Changed glow plugs and harnesses
- Tested each fuse and relay
- Installed new batteries
- FICM tested 48V
- Changed motor oil and filter
- Changed both fuel filters
- Checked for water in the fuel
- Purged air from fuel line
- Replaced dummy plugs
- No codes
- Prayed the rosary
One month later, still crank no start. Thinking about using it as target practice with the AR-15.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Intermittent Crank / No Start
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Crank But No Start - Low Pressure?
2005 F250 To date this has been done, some at different times. ARP studs, OEM head gaskets, heads machined, oil cooler replaced, new fuel injectors, reman'd HPOP w/IPR with STC fitting, EGR delete, 4" turbo back and SCT x3 tow tune.
We originally had a leaking injector that gave us issues (Thread is here) but we pulled the cab and went through the motor, installed studs etcetera.
After the rebuild we ran it approximately 1K miles and it ran great, then one day towing a '65 C10 on a 20' flatbed it shut off while cruising down the road, crank no start on the side of the road, scanguage showed ICP was too low to fire the injectors so we towed it back to the shop and replaced the HPOP, still low ICP.
What's the next step of diagnosis? I'll have ICP numbers by Monday, it's been several months since all this happened and I'm currently out of state trying to diagnose. If i remember correctly the ICP numbers were low teens or 20's. I don't know for sure but I don't think we replace the standpipe or dummy plugs when we had it apart, could that be the issue?
My thoughts are either we have a leak in the high-pressure side or low pressure isn't supplying enough oil to build pressure, so in theory, we would want to check low pressure first, correct?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Crank / Start - All Gauges Shut Off
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Struggles To Start When Crank First Time
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
Ford 6.0L Power Stroke Diesel :: 2003 F250 Crank But No Start - Popping Noise Out Of The Intake?
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2011 F450 Crank But No Start - Codes P0087 / P2291 And P2539
I have a 2011 F450 with a 6.7. It has 99K. The whole fuel system was replaced about 10K miles back. I installed a dieselsite aux fuel filter/water separator after that. Has been running like a top till this am on the way to work. Right before I get to my biz the reduced power warning came on, fortunately I made it into the parking lot at my biz. Then the engine died and it would not restart. Hooked it up to auto ingenuity and I got the P0087 code. I changed the diesel site fuel filters and the stock primary and secondary fuel filters.
The diesel site had a little bit of sediment but no water whatsoever. The Ford filters were very clean and had no trace of sediment or water, but I replaced them anyways. I cleared the code and tried to restart the engine but it will not start. Checked for codes again and now has P0087, P2291 and P2539. The pump is kind of loud when trying to prime the system but there is pressure to secondary filter on engine. I do not have a gauge and adapter to check the pressure yet. I did pick up a replacement pump before the parts dept closed. Could the pump still be bad even tho I do have pressure at the secondary filter?
Ford 6.7L Power Stroke Diesel :: 2011 F250 FX4 - Whining Noise On Cold Start Up
When I start the cold engine mine makes a loud whining noise. I took it to the Ford dealer and they said that the sound is normal and that it's the turbo's. I think I'll take it to another ford dealership and get a second opinion, The service guy has the same truck as me and his was making the same noise on cold start up and they told him it was the turbo's also. Something's not right about the noise.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2011 F250 Oil Leak On Underside Of Engine
Noticed oil on the underside of the engine last oil change, took to Ford dealer for repair under extended warranty. Got a call back today, stating the the oil leak is coming from a injector on the drivers side, and that the injector seals is not covered under warranty. I'm having an issue understanding that oil leaking out from around the injector is not covered under a power train warranty.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Crank But No Start - Check Engine Codes P0299 And P2262
I just got a new 2006 E-350 van about 4 months a go (my previous 2004 got scraped - found out the fuel line leaving the secondary filter into the engine with clogged with bits of paper (wtf?)... after I decided salvaged it for parts for my new van...).
New van drives beautifully in the last 4 months without problem, but shut down on me on the highway yesterday. No strange noise or anything when it went out. I managed to coast safely to the side of the highway. Unfortunately, I cannot seem to start the truck again and had it towed home. It cranks, but doesn't start.
I have a scan gauge ii this time and it shows the following:
KOEO:
FICM ~48.5V
ICP 0
IPR 14.8%
Sync 0
Cranking:
FICM ~48.5V
ICP ~8PSI
IPR 84.7%
Sync 1
I still have a P0299 and P2262 check engine code from 2 days previous to the above, but this doesn't seem to be related to the no-start conditioning (both turbo related)
So, pretty much, I'm looking at a very low ICP. Some research indicates this is is due to a bad HPOP, bad STC fitting, or a massive leak. Given the really low ICP, can I rule out the STC fitting and leak? Looks like only the LPOP is providing pressure. Is there anyway to tell if the HPOP is dead or not once I remove it?
Anything I should shot-gun replace first? I have a bunch of salvaged parts from my old van in my garage, which doesn't include the HPOP unfortunately.
Ford 6.7L Power Stroke Diesel :: 2011 F250 - Leak Coming From Back Of Engine Running Down To Oil Pan
I recently purchased my 2011 F250 Powerstroke a week ago today with 87000 miles on it. the dealer assured me they did all the maintenance on the truck before i was able to drive it home. I noticed on my dash that it kept popping up i needed to change oil soon.. so i got out to investigate and realized i was about a quart low on oil so i looked around more and am seeing that i have a leak coming from the back of the engine running down to the oil pan.. I have not noticed any on on the ground at all but what this leak is coming from...
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2011 F250 Running Sluggish - Check Engine Light Came On
I have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2011 F250 - Oil Leak On Right Side Of Engine Above Valve Cover In The Middle
I have a oil leak that I can't seem to find it appears to be leaking down above the passenger side valve cover and then goes under the engine cover. I don't notice much oil in the valley. This is a 2011 f250 6.7 with 116000 miles on it. I have had no other problems with this truck. Could this be the turbo lines? I am on a RV trip several hundred miles from home so I have very limited tools. The leak doesn't appear to be bad at this point the valve cover is wet with a small drip but it's only in the middle. I just changed my oil prior to the trip when I noticed the leak. I did have a leak on the new filter but a new filter fixed that but still have this one higher up.
View 14 Replies