Ford 6.0L Power Stroke Diesel :: 2006 Truck Will Start To Shudder
So my 06 6.0 4x4 is just about to break 200,000km and I've done most of the upgrades and work myself. (All the updates are in my Sig). My problem is that when I'm cruising and the engine is at full operating temp, if Im bellow 80-100km/h nothing but as soon as I break into that speed range about 2000rpm the truck will start to shudder. Almost feels like its not firing properly is the best way to describe it. Why this could be happening or causing it?
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 Truck Died On Highway / No Start
My truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Cooling Fan Does Not Kick On
I have a 2003 6.0 Exc. I have installed an external "Bullet Proof" oil cooler, and essentially all of the "bullet proofing" accessories with the exception of head studs. I also have installed a Mishimoto oil cooler, as the OEM cooler had a crack in the upper tank, My particular problem is that the cooling fan does not kick on (audibly) until about 230 deg or so. It quickly cools to about 215, and the fan kicks off (audibly). On the long uphills here in AZ, it will repeat this process, sometimes getting as high as 240deg.
(As monitored by my EDGE tuner) I have utilized the blue-wire-to-ground trick noted elsewhere, manually turning the fan on myself, and that works great. What I'm asking, is what sensor sends coolant temp to the ECU, ( and where is it located in the cooling system) which in turn determines how much to turn the cooling fan on? What typical level the sensor sends to the ECU to control the fan? I would like to put together a circuit that "fools" the ECU into turning the fan full "on" at about 210 deg, and stays on until the coolant temp reaches 195 or so. I would like to check that sensor first, and make sure it is working correctly before I try to band aid a fix.
Ford 6.0L Power Stroke Diesel :: 2006 Truck Would Not Crank At All
So I went to start my 2006 this morning and it would not crank at all. Like the battery was dead ( all the light in the cab and headlights were working fine. ) so I tried to jump it and still nothing no clicks not crank no nothing. Just for fun I went ahead and jumped the starter (using the same method as when I prime the hpo system) starter cranked no problem so I put the key in the on position and cranked the key again still nothing. So I put the key in the on position again and jumped the starter truck fired right up. So I went back in the cab and tried to start it with the key and it started right up like nothing ever was wrong. What was causing this? Also my voltage was at 11.5 with the key on and engine off when it was running the volts were at 12 to 12.5
View 5 RepliesFord 6.0L Power Stroke Diesel :: Truck Hard To Start / No Power At All
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Lost Power When Step On Gas And Truck Wouldn't Exceed 15 Mph
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start When Engine Warm
I have recently developed this problem with my 2005 F250 6.0L with 86,000 miles and don't quite understand it. If I drive my truck and then shut it off for a couple minutes, say to go in the store for a few things, when I try to start it back up it won't stay running. It chugs for a couple seconds at real low RPMs (300-400) then just stalls. When I was at the store the first time this happened, I went back in and bought a bottle of starting fluid and gave it a shot, (I know I know, shouldn't do that) and it started right up and got me home.
Thought it was a fluke as the next time I went to start it, it fired right up (sat over night). Drove a couple hours then shut it off, it sat for three or four hours. I went to fire it up to go to a wedding shower down the street about 20 minutes drive and it started fine. Shut it off to go in and pay my "respects" and was out in ten to fifteen minutes. Again Chug, Chug, Chug, stall. Tried to start it with the same results about ten times, then I said fine went back in and ate some free food and drinks for a couple hours and came back out and it fired right up again.
I drove home tonight and while in by drive way at home tonight I verified this again. Turned the truck off and tried to start it back up ten minutes after unloading the truck and same thing, no start. What could be the problem? Only other issue I've noticed was a lack of power on take off from a dead stop then a like a switch the power comes on in about three seconds.
Ford 6.7L Power Stroke Diesel :: Wipers Come On Every Time When Start The Truck
Ok I have this issue that I noticed on my new 2011. May sound weird but the wipers come on when I start the truck every time. Not sure if this is normal but I thought maybe I was bumping the lever thing but it does it anyway. I don't like that doing it cause of snow laying on the windshield in the morning will be a pain.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Truck Will Not Start
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
Ford 6.0L Power Stroke Diesel :: Truck Would Die After Starting Then Start Up Again After A Minute
2004 6.0 Diesel. First the truck would die after starting, then start up again after a minute. Then the truck wouldn't start at all.
Trouble codes indicated low voltage on all injectors leading me to conclude a dead FICM. Replaced the power module in the FICM and reinstalled, but still no start.
48V at driver's side screw under the cover. 12V at the next screw, the next appears to be ground. The passenger side screw is 0V. One post indicated that should also be 48V - is the true?
I probed the power coming in - logic fuse is good. 50A fuse in the cab is good. Relay seems good.
The Ford FICM diagnostic indicates 12V power should be coming in on FICM connector X3 on pins 7, 8, 4, 23, 24, 25. I have 12V only on pins 7, 9, and 27. When I pull the relay I lose power on pin 27.
Ford 6.0L Power Stroke Diesel :: Truck Struggled To Start After Filling Up - Low ICP
Today the truck struggled to start after filling up, even harder the next time, and now it's in my driveway dead and I have a job at work that requires me to go to Michigan next week that I can't afford to lose. On to the issue...
When cranking, my icp won't go above 400psi now, and I understand I need Atleast 500 to fire off. I'm mechanically inclined but new to diesels, so don't be afraid to dumb it down...can't be cocky when your learning. Where should I start my troubleshooting?
Ford 6.0L Power Stroke Diesel :: 2006 - Truck Cranks Over Fine But Does Not Fire
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Missing Until Truck Warms Up
I have a 2006 F250 6.0L. Just had a used motor with 108k miles put in. Had the motor studded, fire ringed, new injectors, new glow plugs, new radiator fluid filter system installed, had egr delete done, ficm board replaced, fuel pump replaced, a few other small items replaced as well. The problem I'm having is the truck runs like it has a miss until it warms up.
After that, it runs fine. It takes about 10/15 miles of driving before it runs like it should. Letting it run in the driveway for 10/15 minutes to warm up doesn't make a difference. When the truck starts, it lopes at an idle for about 5 mins before turbo kicks in & starts whistling. When I start driving it shakes & feels like it has no power until it warms up. Then you'd never know anything was wrong. Put way too much $ into the truck so far and can't keep going.
Ford 6.0L Power Stroke Diesel :: 2006 Truck Shuts Off In A Hard Pull
I have a 2006 that shuts off in a hard pull, if I wait 3 minutes it starts again. I hooked up my scan tool and when it dies and I crank it it only builds 200psi oil pressure, let it sit it builds enough pressure to run fine. If I dont push it over 3500psi for more than minute it wont die pull a hill it dies again. Is it the hpop or an o-ring.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Truck Would Not Start And Threw FICM Codes
My f250 was parked this winter to get work done. I had put a new exhaust on and while crawling on the engine bay it had kicked the fuel reset by the passengers kick panel. After pressing that button the truck would not start and threw FICM codes. (Power low to FICM) and my Scanguageii had said that power was very low (27 volts) during cranking. I sent the FICM to FICMrepair.com. Today I had put the FICM back into the truck and went to start it. I cycled the plugs 3 times and started on the 4th. The truck did not start after this and had thrown more ficm codes. What it could be?
View 12 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / Crank After Oil Cooler Rebuild
Had to do the icp sensor originally. went in from the top and discovered my oil cooler was failing too. so i did that. with weather (too tall to fit in the garage) and life getting in the way it's taking me 2 months a little here n there to actually get it done so she's sat for a while. yesterday was moment of truth to get it started again. the batts were old before i started working on it. so i replaced those yesterday.
I've tried and tried to get it to start and it won't turn over. it did for one tenth of a second try. nothing since. I saw that my shifter wasn't exactly in park so i wiggled it and tried to crank it again and now it won't even crank. I have a feeling somehow the transmission isn't reading in park or neutral so it's refusing to crank. I really don't want to tow it.
Ford 6.0L Power Stroke Diesel :: 2004 Truck Died While Running / Won't Start
Last friday, my truck died while running. I let it sit for a few hours, went out and it started right up. Went to get pizza for my kids and I got 5 blocks from my house and I barely had any power. Truck died again while getting pizza and had to tow it home. Now it will not start. I have checked fuses, taken apart the fuel pump on the motor and cleaned the water from it, added a fuel treatment and also did an old truckers trick with the fuel (10% gasoline). the truck will crank and make an attempt to fire but it will not start. I have 3 kids and this is my ONLY transportation. I need to get this thing running STAT.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / Cranks Just Fine Just Doesn't Try To Run
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Truck Only Cranking And Refuse To Start
I need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 Replies