Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Shuts Off For No Reason / Codes P0606 And P0341
I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
Ford 6.0L Power Stroke Diesel :: P0470 And P0069 Codes - No Boost
Got a P0470 code check engine light on. It's - 12 outside. Having problems with this in the cold? I seen something awhile back about a TSB about ice forming on the sensor on 06-07 engines. It's the second time thus winter it has come on both times it was - degrees out.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Power Loss - No Boost And Codes?
Truck = 2011 F250 150,000 miles, no modifications, stock.
Truck lost power yesterday, no boost, and no codes. When driving on Friday, I started moving from a red light. The truck seemed very sluggish. Then I noticed it downshift going up a small hill that it never downshifts before. I looked, and noticed the turbo gauge at 0, no boost. I pulled over, turned it off, then restarted it, but still no boost, and the truck is very under-powered. I looked over the area, and do not notice any leaks, also no leaks underneath. I hooked up my OBD reader, and no codes., the boost gauge is on zero, and the truck has lost significant power. I no longer hear the turbo spooling.
I have spent the past several hours searching sites and forums (Started with FTE ), and it seems that most believe a restart of the truck has solved it for them. However, this is not the case for me, a restart, even after letting it sit overnight did not resolve the issue.
I did see one reference that replacing a NOX sensor solved their problem. This brings up some interesting truck history. Back in June 2017, my truck threw the following codes, P207F and P20EE.
P207F - Reductant Quality Performance
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
The message said I have 200 miles until reduced power. Since it was a Friday, not much I could do at the time so I let it sit overnight, and then the next morning the message was gone. I plugged in the OBD reader and cleared the only remaining code (P20EE), and its been a very happy truck until yesterday.
So my question, can a bad NOX sensor cause the issue of loss of turbo boost, with no codes? Is there another possible cause?
Ford 6.0L Power Stroke Diesel :: Code P0237 - Truck Won't Build Boost Over 11 PSI
P0237 code. The truck is a 2003 f250 with an edge evo . The truck will run great then throws this code and won't build boost of over 11 psi. Now it even drops it right off to 0. I replaced the map sensor a month ago and doesn't seem to have fixed anything.
View 2 RepliesFord 6.7L Power Stroke Diesel :: Truck Making A Lot Of Noise When Tried To Accelerate - Boost Gauge On Dash Stuck At 35 PSI
Was driving back home from shopping tonight and my truck was making a lot of noise when I tried to accelerate. I noticed the boost gauge on the dash was stuck at 35psi but the MiniMaxx showed 0psi.
No engine light so I babied it home which was about 30mins driving and managed to accelerate slowly to avoid the engine rattling. I didn't want to shut it down and restart in case it wouldn't start again for some reason.
When I got home I idled until EGT was <300F like I normally do (it never went over 700F when I was driving home) and then restarted it. The gauges worked fine, MiniMax showed boost and the engine revved freely with no rattling noise. I haven't taken it out for a road test, I'll do that when it's daylight.
Bad sensor somewhere? I would think if the turbo had failed it wouldn't have been fine after a restart.
Ford 6.0L Power Stroke Diesel :: 2005 - Low Boost No Power
I've got an 05 EX 4x4 150k miles. Stock tune, EGR delete only ....
Driving along and everything was good plenty of boost no power issues. Got off the freeway and truck just stopped making boost. So I messed with it for a couple days. Cousin with a Mac scanner flaked on me so I was stuck using Edge gauge cluster and trying to trouble shoot.
NO CODES, No smoke, EGT's rise and truck seems like it is lean. Boost has fluctuated between 4psi to 11 psi. What should MAF be at idle?
ICP has been consistent with whatever boost levels were being made.
FICM 47.5
New MAP tube/nipple cleaned
New MAF
Clean Air filter
New fuel filters
VGT actuates
Accel ped in spec
Turbo spins free
New hot side CAC boots
Ford 6.0L Power Stroke Diesel :: 2005 - Code P0299 Under Boost Condition
I'm having a little trouble with my 05 Excursion 6.0L .... We took off camping the other day pulling our 30' camper and the engine light came on pretty much as soon as we hit the highways. I checked my Dash boss and it came up as P0299 under boost condition. The truck never skipped a beat. The boost gauge never dropped and it seemed to have lots of power. Actually I've noticed too much boost while pulling. It's climbed up to 36psi before and was still climbing when I backed off the throttle. I'm thinking the turbo is fine but not sure what to check next.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Lack Of Turbo Boost At Startup
I've been having issue with my truck lacking boost over the past month or so. The psi levels are normal in the morning when I start it up cold, the problem almost always occurs at start-up when the truck is somewhat warm and has been sitting for an hour or more after use. I've had boost levels at idle from -0.14psi to -0.56psi and as low as -1.2psi when driving as the problem is occurring, but it eventually kicks on and goes to normal levels after several minutes of driving. After originally taking the truck to a local diesel mechanic I was told it had EGR codes and they recommended installing an SCT tuner and cleaning the EGR valve to solve the problem. I had them install an SCT 5015 tuner and clean the valve but I've still been having the problems with boost.
View 2 RepliesFord 6.7L Power Stroke Diesel :: Truck Has No Power Barley Moves / Codes PO113 And PO4DA
OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Truck Would Not Start And Threw FICM Codes
My f250 was parked this winter to get work done. I had put a new exhaust on and while crawling on the engine bay it had kicked the fuel reset by the passengers kick panel. After pressing that button the truck would not start and threw FICM codes. (Power low to FICM) and my Scanguageii had said that power was very low (27 volts) during cranking. I sent the FICM to FICMrepair.com. Today I had put the FICM back into the truck and went to start it. I cycled the plugs 3 times and started on the 4th. The truck did not start after this and had thrown more ficm codes. What it could be?
View 12 RepliesFord 6.0L Power Stroke Diesel :: Truck Turns Over Just Fine But Won't Fire With Codes
Got up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
Ford 6.0L Power Stroke Diesel :: 2005 - Puking Coolant - No Codes?
Ok so I have a 2005 f250 6.0L. It is fully bulletproofed with ARP head studs. I am running a sct anarchy on street tune. My problem is that sometimes it is "puking" coolant from the degas bottle but only a drop every now and then around the cap; it drives fine, no trouble codes, the engine and trans temp is fine and it's not blowing white smoke it still blows black smoke, and there is no coolant smell just straight diesel. What might be causing it to puke a drop of coolant every now and then?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Codes P0279 And P0281 / Injector 7 Bad
I have a problem with my 2005 F250 6.0 with about 156,000 give or take. Started having a problem a few weeks ago started missing and fuel mileage went south and had it scanned. Codes pulled was P0279 and P0281, I was told probably #7 injector bad so I replaced it cleared the codes and Cranked right up no problems until a few moments later the truck started acting up again. Run smooth than rough idle, smooth, rough idle. Same codes! Tested the FICM while on the truck, it showed like 47.5 volts before cranking and 48 volts when cranked.
I have tested the Ohms between the Injector harness end and FICM end. Pin #2,3,4 all showed 0.3 Ohms, #1 did not even register like 0.L on my Ohmmeter. Took FICM all the way off and it made a rattling sound inside, took it apart and about 4 pieces of what a buddy says where resisters. SO I guess my question would be , is FICM bad? Did something short it out, and/or is the number 1 injector wire bad. Plus the when I took the FICM off the back 2 bolts where loose, so I guess the FICM was bouncing up and down maybe. The front 2 where tight.
Ford 6.0L Power Stroke Diesel :: 2005 - Truck Stalled / Shut Off When Going At 55 Mph
Just got this injectors done. Filled the tank up. Drove for 1/4 of a tank. Went to leave out yesterday. Made it out of my subdivision and down the road 3 miles or so. I was going 55 when the truck stalled. I tried to start the ignition it would turn over, but wouldn't catch to stay running. I did this at least 8 times. Friend came with Ether. Tried 3 separate times, truck started going dead. So i was about to give up... Tried it 1 last time, it fired up like a champ!
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 Truck Dies Under Load?
So pulling my trailer and 4x4 and the truck dies without any other symptoms. No check engine light all other electrical remains working. This happened 6 times this trip always while pulling a grade but only after the truck has been running for a few hours. Each time, no warning and once the truck has set for 5 to 10 minutes it start up like normal. The longer i let it set the longer I can run before it does it again. ICP is 550ish at idle, 200ish while cranking. Check the FICM before the trip and it was at 47.5 to 48.5v key on engine off and running. STC, stand pipes, dummy plugs, ball cups have all been done.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - GPCM Getting Hot With Truck Off
I've got a problem with an '05 f-350 with the 6.0. Initially I had a code for the #1 glow plug so I replaced the plug and the code was still there. Next I tested the harness and the rest of the plugs on the same harness and everything checked out fine. This lead me to the Gpcm which I then replaced. The first thing I noticed was when removing the old Gpcm I got a spark when removing the mounting nuts.
When I installed the new Gpcm the truck started fine and no codes came up so I thought all was good till I went to start the truck the next day and the batteries were dead. I thought I possibly left something on so i started charging the batteries but noticed they seemed to have a draw on them. I put my hand on the new Gpcm and it was very warm with the key off so I have the batteries disconnected till I can figure this out.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Wandering To The Right
My 05 F250 CC 4x4 had a problem where it was wondering to the right.
I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).
Had two new front tires installed/balanced and the problem seemed to go away for a few months.
Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?
Ford 6.0L Power Stroke Diesel :: 2005 - Rough Idle - Codes P0672 / P0674 / P0678
I have a 2005 f350 6.0 power stroke. I had a crank no start when hot issue. I bought an obd scanner with the torque app. IPR was at 85%. ICP pressure was low. I got the IPR out and bought a new screen because it was clogged. Upon putting in I broke the injector female side plastic connection.I bought the injector connector piece and installed it. After putting everything back together it starts but runs very rough,low power. The IPR was fixed. ICP,ipr and ficm are at good levels now.
IPR=14.7%-30%
Fcim sync=1.0
Fcim voltage=48.5
ICP pressure (idle)650-850psi
My fault codes are:
P0672 (glowplug)
P0674 (glowplug)
P0678 (glowplug).
Why it would be running/idle rough?
Ford 6.0L Power Stroke Diesel :: 2005 - Truck Only Cranking And Refuse To Start
I need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 Replies