Ford 6.0L Power Stroke Diesel :: 2005 Truck Buck / Miss Not Just Under Load
Truck has not been bullet proofed and has aftermarket air intake. Truck has 185km on it (purchased at 160km a year ago). For the Ham Radio guys out there, this is the most electrically noisy vehicle I've owned with S9+ noise while accelerating and S7 going down the highway ...
The faults show up as:edit Can be hard to start cold, takes couple of tries if it's been sitting for a bit (week or more)
No power when cold, that is a lot of pedal results in little power
Misses a lot when cold
Light blue smoke when missing when cold
When fully warmed up which takes 15 minutes of idling regardless the time of year:under load (heavy acceleration while loaded or not, or just in towing, or carrying) it misses a few times a minute, otherwise runs well
It feels like it just doesn't fire a cylinder if it were a gasser, or as if the spark plug weren't connected, but it's not a constant miss, it is intermittent. No load means hardly any misses. Load means lots of misses even running down the road. Should be pulling hard up a hill where it misses lots more.
What I've looked at :
FICM voltage 47.8 standing, 47.6 cranking and running.
FICM is aftermarket and there are no cold solder joints.
Added Archoil 9100 with no change
Wires to FICM are tight and connectors aren't cracked
edit Wires to Injectors are tight and connectors aren't cracked
Exhaust temps range between 500F and 800F during any of these events
Basic ODB reader shows no codes
I'm looking for a couple of things - I'm not much of a mechanic so this has to go to a shop for diagnosis and repairs. Before I run it someplace, what sort of diagnostic tools should that shop be equipped with to find out what's going on? Also, given what you know of the problem, am I likely to damage things if I continue towing activities?
Ford 6.7L Power Stroke Diesel :: Will Airbags Make The Truck Less Bouncy Under Load?
2015 F350 CC LB FX4. I routinely haul 2-4k of cargo in the back of my truck for 375 mile jaunts.... I do this at least once a week. Most I've ever hauled in the bed was 5k and it rode better than it does with 2k in the bed.
The ride is awful and the bounciness and instability driving on uneven roads or corning at speed is starting to really annoy me. Would a set of good airbags cure this problem? Hit a pot hole while corning on the highway around 60-70mph and you better hang on... feels like the back end is going to jump off the ground.
On my last trip down it was so bad I actually pulled off the side of the highway to see if one of my rear springs was broken. And yes... the cargo is evenly distributed under my truck ARE canopy. E rated tires set at 80 PSI rear, 65 PSI front.
Ford 6.0L Power Stroke Diesel :: Truck Dies Within A Minute After Starting
Parked the truck last night and all was fine. Went to start the truck today and let it warm up before hooking up the trailer and it dies withing a minute. Go to start it again and nothing. End up killing batteries. Checked for codes and had a bogus EGR code P0404. Bogus because the tune I run doesn't have the EGR enabled and it is deleted. Still plugged in though.
Hooked up dual battery chargers and sent the boy to pick up fuel and oil filters and oil. It was over due in both areas. Changed both and still no love. So I drag out the laptop and set up my AE to monitor FLP, FLM, IPR, ICP, ICV, Sync.
KOEO
FLP 11.00
FLM 47.0
ICP 0
ICV .24
IPR 14.25 odd right?
Synch 0
Cranking
FLP 9.6
FLM 47.0
ICP 800-1600 varied the longer I cranked
ICV 2.2
IPR 14.24
Synch 1
still no start.
Still no codes.
I then cycled the IPR through AE a few times and turned the key. Damn thing fired right up.
Idling
FLP 11.0
FLM 47.0
ICP 875
ICV 1.4ish
IPR 26.4
Synch 1
I pushed the RPMs up to 2500
FLP 11.0
FLM 47.0
ICP 2200 iirc
ICV 2.24
IPR 42.0ish
Synch 1
Turned the truck off and restarted it a few times. No issues. Turned it off and pulled the positive cables and put the chargers back on it.
So the question is .....Is the IPR sticking on me? I just replaced the HPOP in the spring along with the up pipes. Made sure everything was clean. I actuated the IPR and cleaned it out. Put a new screen on it had zero leaks.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Lack Of Power / Truck Will Barely Move And Takes Long Time To Accelerate Under A Load
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Ford 6.0L Power Stroke Diesel :: 2005 Randomly Chugging Under Load
While i am pulling a loaded trailer we have been experiencing a random Chug that only last about 1 second we have no lose of power during when it happens. We Recently just replaced all fuel Filters. We have an updated EGR on it with a cold air intake and muffler delete. It has about 180000 miles on it it runs awesome and starts right up just trying to figure what this problem could be..
View 11 RepliesFord 6.7L Power Stroke Diesel :: 2016 F350 - Flutter Comes On When Truck Goes Under Load For A Short Period Of Time
I have a 2016 F350 Powerstroke fully deleted for about 3k miles. Truck was running perfectly then out of no where started running like crap and had very minimal power 500-2000rpm. Once 2000rpm hit, turbo spooled up and made power. Very odd. I cleaned out back pressure sensor, map sensor and hoses. No fix. Did a hard reset and the truck ran fine again and had low end power.
Ever since then I started hearing very odd fluttering sounds coming from what I think is the turbo. Also noticed my OEM boost gauge doesn't work. No reading from it.
The flutter only comes on when the truck goes under load for a short period of time and then I let off the throttle. It seems to running fine other then that and maybe a little bit more sluggish then normal. Any things I can check before I put it back to stock and bring it to the dealer?
MODS:
NO Limit EGR Delete
Flo-Pro 5" Straight
S&B Intake
SCT Livewire w/ custom tunes
Also, I had a lot of problems with my live wire software. I have to send it back to SCT to get warranty problems fixed which I'll be sending out Monday. They think my tuner is stuck in demo mode for some off reason.
Ford 6.0L Power Stroke Diesel :: 2005 F350 Dies While In Gear?
I have a 2005 f350 king ranch,I have a kinda weird problem.the truck starts up and runs great as long as I let it get to normal temp.but if the motor is cold it will idle fine but if I goto put it in gear it just dies.sounds like tc is locking but I don't get any codes.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Starts And Dies Numerous Times
I've got an '05 F-250 starts and dies numerous times, have to rev throttle to keep running then it stays running. I've replaced FICM, PCM, Eng. harness, IPR, CMP, what else is there to do?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Truck Stalled / Shut Off When Going At 55 Mph
Just got this injectors done. Filled the tank up. Drove for 1/4 of a tank. Went to leave out yesterday. Made it out of my subdivision and down the road 3 miles or so. I was going 55 when the truck stalled. I tried to start the ignition it would turn over, but wouldn't catch to stay running. I did this at least 8 times. Friend came with Ether. Tried 3 separate times, truck started going dead. So i was about to give up... Tried it 1 last time, it fired up like a champ!
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - GPCM Getting Hot With Truck Off
I've got a problem with an '05 f-350 with the 6.0. Initially I had a code for the #1 glow plug so I replaced the plug and the code was still there. Next I tested the harness and the rest of the plugs on the same harness and everything checked out fine. This lead me to the Gpcm which I then replaced. The first thing I noticed was when removing the old Gpcm I got a spark when removing the mounting nuts.
When I installed the new Gpcm the truck started fine and no codes came up so I thought all was good till I went to start the truck the next day and the batteries were dead. I thought I possibly left something on so i started charging the batteries but noticed they seemed to have a draw on them. I put my hand on the new Gpcm and it was very warm with the key off so I have the batteries disconnected till I can figure this out.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Wandering To The Right
My 05 F250 CC 4x4 had a problem where it was wondering to the right.
I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).
Had two new front tires installed/balanced and the problem seemed to go away for a few months.
Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?
Ford 6.0L Power Stroke Diesel :: 2005 - Truck Only Cranking And Refuse To Start
I need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 Truck With Low Boost And Gasser Codes
This isn't my truck, but I'm trying to diagnose it for a friend and I haven't seen it. He's scanning it with a high-end Matco scanner so I'm not convinced that the scanner is reading right but here's what I've got:
P0056 (2), P0161, and P0300 (random misfire detected). The first two are "gasser" codes and don't show up in the 6.0 bible code list so I'm wondering if they were added in to some of the later flashes??
The truck has a "new" OEM turbo and won't build over 18 psi of boost but, according to the owner, who is a decent mechanic, it's absolutely clean inside. Looking for about the weird codes it's throwing?
All my years of information on 6.0's was stolen with my laptop last year ....
Ford 6.0L Power Stroke Diesel :: 2005 Missing / Truck Started Running Rough
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Will Run For A Few Minutes Loose Fuel And Stopped
I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem
View 12 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Truck Not Move When Stop At Light Or For Any Reason
I have a 2005 Ford F-250 Powerstroke. At times when stopping at light or for any reason, I give it gas but it does not want to go. It's like it is not even registering that I am pushing the pedal. I shift it into neutral and rev it up then switch it back to drive and it goes and puffs out smoke. What is going on?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Engine Change Out Now The Truck Will Not Start On Hot Crank
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Truck Shuts Off For No Reason / Codes P0606 And P0341
I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
Ford 6.7L Power Stroke Diesel :: 2015 - Shaking Under Slight Load Due To A Small Incline And Loud Diesel Sound
So I have just over 14k on my 2015....... I love the truck but have had a few small issues. I had a water leak coming in from the roof that would leak through the grab handle. Nothing major dealer replaced one clearance light seal and they said the windshield needs to be re sealed.
Then I had a god awful irritating squeak in the dash..... It only does it late In the day when it's been hot. The dealer said it was a loose air bag. I have had the truck back a week and it's doing it again.
Those are little issues that will get resolved...... I hate having problems with a brand new vehicle but I understand it happens and that's what warranty is for.
I also reported a bad shake to the dealer...... The truck will shake very violently and have a very loud "diesel" sound. It's very specific at when it occurs. It has only done 4 times in the past 6 weeks including today. The odd thing is the 4 times it has done it has been the same time of day in the exact same spot on the exact same road!!!!
Basically I leave my office sit in some traffic and by the time I get to the parkway it has been35 minutes or so. Only happens in 6th at 60 which is roughly 1,400rpm a slight load due to a small incline and it shakes real bad! The typical "diesel" sound you get when under a load is very pronounced almost to a knock. It will continue to do this as you slowly increase throttle until it down shifts and then goes away. I also caught it doing it and I manually shifted to 5th and it went away.
Because of the rpm at which it happens with slight load only doing it in 6th I lean to a Trans issue and more so a converter problem. It feels like converter shutter. I just don't understand the engine sound.
I gave very descriptive info to the dealer..... Several techs drove it and could not duplicate. I just picked the truck back up last Thursday and the dash squeak is back and the shake happened yesterday and again today. So I am a bit irritated to say the least.
I really hate the fact that I know there is a problem but I also understand if a tech can't duplicate it he can't diagnose it. However today I did get a video of it with my phone so they will know I'm not making this crap up!