Ford 6.0L Power Stroke Diesel :: 2006 F350 Shut Down / Stalled / Misfiring And Hard Start
Fuel injectors do this? They are off a 2006 Ford F350 dually with the 6.0 diesel motor! Have replaced all 8 fuel injectors got back drove for 200miles and fuel injectors 4 and 8 were throwing codes changed them out and high pressure oil pump oil coolant deleted egr valve changed the ipr valve feed tubes to the oil rails. replaced the FICM. Yet again drove for 2 days about 200 miles again and shut down (stalled) misfiring hard start. and now fuel injector 4 is throwing codes again. Have not drove it since we got it home from the last stall out which was a few feet from our drive way and we towed it home.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Truck Started Surging Then Stalled
Last night pulled in at rest stop and truck started surging then stalled put dieselkleen in and topped off tank but no luck eventually would not run at all. Had it towed to ford and this morning started right up running fine. Having them change fuel filters. Not sure what to do got to get back to drive?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Driving Along Truck Just Stalled When Hit A Bump
The first time it happened, I wasn't monitoring any PIDs as I didn't have my phone with me. Not really sure if I hit a bump or anything, it just stalled. I pulled it off to the side and put it in park and started cranking. Turned over rapidly but wouldn't start. I started freaking out thinking what am I going to do? Shut the truck completely off and waited a couple minutes and then turned the key and it started right up. Drove to my destination and didn't have another issue.
I'm only driving my truck on weekends as I have a company van and I can't park my truck at the condo I'm living at right now. So sometimes it's a few weeks between drives. This has been the story of my truck use since I nought it 3 years ago. In fact I know my turbo is sticking as the most boost it builds is 20-22 psi. I probably have a sticking injector too, as it smokes unburnt fuel until warm.
So the last few weeks when driving, I've noticed that if I hit a big bump, occasionally it dies again. What I've discovered is that it won't start unless I shut the key off entirely. Meaning, if it stalls I put it in neutral as I coast, shut the key off as far as it will go and it will start up. If I just throw it in neutral and try to start, it won't.
Watching my Torque Pro display, I've noticed that it locks up (like normal when I shut the truck off w/o shutting the Torque app off). The display then has read lower voltages than normal for FMP, FLP, FVP (main, logic and vehicle? can't remember ). FMP is normally at 48.5v and the other 2 hover around 13.9v. The last time it stalled, I noticed 9.3v for FLP and FMP was 23.4. I'm not sure if this is what it shut off at or if I panicked and tried starting it w/o shutting the key off entirely. So please don't take those readings as gospel.
I scanned it for codes, but nothing popped up.
Ford 6.7L Power Stroke Diesel :: F350 - Truck Shut Down While Going At About 25 MPH
I am getting ready to go on vacation this weekend with my f350 and I was driving today when suddenly the truck shut down while going at about 25 mph. I tried to start it and it just kept cranking. I got it started 5 mins later and it threw a P0069 code. I drove for about 2 more miles and it shut down again, and started right back up. I'm guessing map sensor? This was the last thing I needed to happen!
View 14 RepliesFord 6.0L Power Stroke Diesel :: Truck Shut Down While Driving
So I am out of town about 120 miles from home on a job. I was driving down the mountain road to the store and my tuck just shut down. Lucky for me I was able to get into a turn out. So I try to start the truck and it will not fire. I check for codes I am getting p2614, p2617 so I was able to clear the codes and get back to the house I am staying in. What is going on with my tuck. Oh ya the code did not come back on in the 15 min drive to the house. Also just finished up doing a y pipe and my egr o ring so I and the intake and all that off.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Truck Shut Down While Driving / Code P2614
So a few day ago my truck shut down while driving. I posted up and checked the ficm harness as suggested. Things were a bit lose so I zip tied my harness around the ficm. Thought it was all fixed and test drove it and it shut down again. I tried to start it a few times and my ICP was a tad low about 450 ,I have a brand new ICP and harness. Checked my scan gauge and I have code p2614. I cleared the codes and the truck started right up. I need to get this sorted out I was supposed bro go home tomorrow from working out of town all week about 100 miles from home...
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Won't Shut Off By Key?
I have a 2005 f350 6.0 and it has a startup kit installed. When I start by using the key works perfect. But won't shut off by key! I have to use the stop button on key fob to kill the engine. I'm thinking relay might be stuck? And the relay on start up kit is working? Key removed it doesn't diesel down, it runs like key is still in.
View 12 RepliesFord 6.7L Power Stroke Diesel :: Strange Pumping Sound Coming From Under The Hood After Truck Shut Off?
What could be making the strange pumping sound coming from under my hood after I shut off the truck?? It sounds like a small compressor or pump running.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Losing Coolant Pressure - Pin Hole Leak Somewhere Once Shut The Truck Off
I noticed when I shut off the truck about 30-40 minutes later I'll open the degas bottle cap and notice there is no pressure.
I used a coolant pressure tester kit and pumped in 16PSI but couldn't hear or find the leak.
I'm going to buy a smoke machine in a month or two but until then, can I still drive the truck ?
I'm guessing it is a pin hole leak somewhere as once I shut the truck off... there is a lot of coolant pressure.
Ford 6.0L Power Stroke Diesel :: 2005 F250 Will Shut Off After About 20 - 30 Minutes Of Driving
Been chasing my tail and can't figure out an electrical issue. My issue is that I'll drive for about 20-30 min and the truck will shut off while driving. I'll pull off the road, let it sit for 10-20 min (cool down) and It will fire back up and go for another 15 min or so. Sometimes it will glitch/wig out when i try to start or not start....
I've replaced the following and monitored everything on a scanner.
-cam sensor
-crank sensor
-2 new batteries
-flashed the ecu
05' F250 6.0 King Ranch 4X4
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Seems Like Fuel Shut Off - FICM Smoking?
2005 f350 6.0. I was driving my truck and it seemed like someone had shut the fuel off to truck ! i had it towed to the house and was doing research and watch a video on checking the ficm with a volt meter..when i touch the positive post from meter the ficm started smoking and sizzzling...but back tothe truck when i try to start it i have no pre warm up sounds coming from the truck and the truck just turns over strong ..no start...i was going to replace the ficm but didnt want to spend the money to fry another if that is not my problem..also the # 5 fuse under the hood keeps blowing.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2005 Truck Dies Under Load?
So pulling my trailer and 4x4 and the truck dies without any other symptoms. No check engine light all other electrical remains working. This happened 6 times this trip always while pulling a grade but only after the truck has been running for a few hours. Each time, no warning and once the truck has set for 5 to 10 minutes it start up like normal. The longer i let it set the longer I can run before it does it again. ICP is 550ish at idle, 200ish while cranking. Check the FICM before the trip and it was at 47.5 to 48.5v key on engine off and running. STC, stand pipes, dummy plugs, ball cups have all been done.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - GPCM Getting Hot With Truck Off
I've got a problem with an '05 f-350 with the 6.0. Initially I had a code for the #1 glow plug so I replaced the plug and the code was still there. Next I tested the harness and the rest of the plugs on the same harness and everything checked out fine. This lead me to the Gpcm which I then replaced. The first thing I noticed was when removing the old Gpcm I got a spark when removing the mounting nuts.
When I installed the new Gpcm the truck started fine and no codes came up so I thought all was good till I went to start the truck the next day and the batteries were dead. I thought I possibly left something on so i started charging the batteries but noticed they seemed to have a draw on them. I put my hand on the new Gpcm and it was very warm with the key off so I have the batteries disconnected till I can figure this out.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Wandering To The Right
My 05 F250 CC 4x4 had a problem where it was wondering to the right.
I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).
Had two new front tires installed/balanced and the problem seemed to go away for a few months.
Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?
Ford 6.0L Power Stroke Diesel :: 2005 - Truck Only Cranking And Refuse To Start
I need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 Truck With Low Boost And Gasser Codes
This isn't my truck, but I'm trying to diagnose it for a friend and I haven't seen it. He's scanning it with a high-end Matco scanner so I'm not convinced that the scanner is reading right but here's what I've got:
P0056 (2), P0161, and P0300 (random misfire detected). The first two are "gasser" codes and don't show up in the 6.0 bible code list so I'm wondering if they were added in to some of the later flashes??
The truck has a "new" OEM turbo and won't build over 18 psi of boost but, according to the owner, who is a decent mechanic, it's absolutely clean inside. Looking for about the weird codes it's throwing?
All my years of information on 6.0's was stolen with my laptop last year ....
Ford 6.0L Power Stroke Diesel :: 2005 Truck Buck / Miss Not Just Under Load
Truck has not been bullet proofed and has aftermarket air intake. Truck has 185km on it (purchased at 160km a year ago). For the Ham Radio guys out there, this is the most electrically noisy vehicle I've owned with S9+ noise while accelerating and S7 going down the highway ...
The faults show up as:edit Can be hard to start cold, takes couple of tries if it's been sitting for a bit (week or more)
No power when cold, that is a lot of pedal results in little power
Misses a lot when cold
Light blue smoke when missing when cold
When fully warmed up which takes 15 minutes of idling regardless the time of year:under load (heavy acceleration while loaded or not, or just in towing, or carrying) it misses a few times a minute, otherwise runs well
It feels like it just doesn't fire a cylinder if it were a gasser, or as if the spark plug weren't connected, but it's not a constant miss, it is intermittent. No load means hardly any misses. Load means lots of misses even running down the road. Should be pulling hard up a hill where it misses lots more.
What I've looked at :
FICM voltage 47.8 standing, 47.6 cranking and running.
FICM is aftermarket and there are no cold solder joints.
Added Archoil 9100 with no change
Wires to FICM are tight and connectors aren't cracked
edit Wires to Injectors are tight and connectors aren't cracked
Exhaust temps range between 500F and 800F during any of these events
Basic ODB reader shows no codes
I'm looking for a couple of things - I'm not much of a mechanic so this has to go to a shop for diagnosis and repairs. Before I run it someplace, what sort of diagnostic tools should that shop be equipped with to find out what's going on? Also, given what you know of the problem, am I likely to damage things if I continue towing activities?
Ford 6.0L Power Stroke Diesel :: 2005 Missing / Truck Started Running Rough
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Will Run For A Few Minutes Loose Fuel And Stopped
I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem
View 12 Replies