Ford 6.7L Power Stroke Diesel :: 2011 F250 - Random Codes P0281 And P0278
I have a 2011 F-250 with 112k miles.
On 11/25/2016 at approximately 110k miles: my truck was 100% stock. I was about a half hour into a 3 hour drive and I got a Check Engine Light. I stopped to get some food and my truck was idling for about 10 minutes when the light came on. My code reader said it was for P0278 "Cylinder 6 Contribution/Balance". I cleared the code, restarted the truck and drove away.. I drove about another 5 minutes until I started hearing a real bad air leak and the truck just didn't feel like it was driving right. Check engine light never came back on, but it just didn't feel right so I towed it home.
The truck went to the dealer, they said they found the EGR Inlet Tube was cracked, and that explained the air leak sound I heard when I continued driving, and they said the truck was probably running rich from the lack of air and that set the P0278 code. They replaced the tube and everything was fine.
On 12/14/2016 with around 111,500 miles: upset that just one pipe breaking could take down the whole truck with no one having that part in stock to get me back on the road, I "deleted" my truck. Removed the DPF, installed "block-off" plates for the EGR (which goes in place of the EGR inlet tube), a Cold-Air Intake, and H&S MiniMaxx. (Exact parts can be found in my signature).
On 12/25/2016 with around 112,500 miles: I was getting ready for work and I started my truck using the Ford Factory Remote Start that was original equipment on the truck. The truck ran for about 10 minutes when I hopped in it and took off. As soon as I got in it, The Check Engine Light was on and I had a code for P0278 "Cylinder 6 Contribution/Balance". I erased the code and restarted the truck.. drove to work (around 50 miles) with no problems. Truck ran fine, I never felt any problems, and no smoke or anything like that.
10 hours later I'm getting ready to leave work and let the truck run on remote start for 10 minutes. I hop in the truck and drive away.. there's no check engine light, but, my tuner says there's two DTC's.. P0278 "Cylinder 6 Contribution/Balance" and now P0281 "Cylinder 7 Contribution/Balance"... I cleared the codes, restarted the truck, and drove home with no problems.
12/26/2016 I started the truck on remote start again for 10 minutes. No check engine light, but the tuner says there's one DTC for P0281 "Cylinder 7 Contribution/Balance". Cleared the code, restarted the truck, and drove to work with no problems. Got back in the truck after 12 hours, drove home and didn't get a DTC or Check Engine Light on the drive home.
12/27/2016: No DTC's or Check Engine light. Where I should start looking to fix this?
Ford 6.0L Power Stroke Diesel :: 2006 F250 Error Codes - Injector Control Pressure Sensor Circuit Intermittent
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Shuts Off For No Reason / Codes P0606 And P0341
I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
Ford 6.0L Power Stroke Diesel :: 2005 - Injector Intermittent Code
Been working on a 2005 6.0 with 218kish miles on it. When I got the truck it had a contribution 2 code stored, no check engine light, just could see the code on the code reader.
Truck idled like crap, lacked power, so I replaced the injector. Truck improved but still had a miss, this time it had a stored code of injector 6.
Ordered another injector, got it installed today. Fired the truck up, ran perfectly, drove it around, absolutely 0 issues ran like a dream. Parked it for a few minutes before starting it again to wash it. Rough idle, not horrible, not noticeable. Cylinder 6 contribution code stored again, no check engine light.
So I drove it, I drove the hell out of it for about 15 minutes with the AC at full blast, WOT, etc etc. By the time I was done, truck was back to running smoothly.
Just walked outside after dinner to see if it would still perform well, or if it would idle poorly again, sure enough, 6 contribution, rough idle.
I just changed fuel filters with OEM, air filter is new. I just cleaned the EGR valve- although maybe it's not clean enough?? Oil change is tomorrow (had to wait for the filter to get shipped in).
I'm at a little bit of a loss on how to cure this miss, unless it's possibly an oil pressure issue from bad/old oil causing it?
Ford 6.0L Power Stroke Diesel :: 2005 Injector Harness Fit On 2004?
Will a 05 injector harness work on a early 04?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 Leaking Coolant After Injector Replacement
I recently had my injectors changed at Ford and while I was driving it started dumping coolant. If the leak can be cause from the injector replacement or if they didn't put something back together right... 2005 f 350 6.0...
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2014 F250 - Codes P207F And P04DB
I have a 2014 F250 CCSB that I bought new, I now have 41,000 mi on the truck. Earlier this year it had the P207F code come up and subsequently the computer derated the power to idle. I was able to get it to the dealership and they could not figure out why the truck had this code come up, it is an exhaust fluid CEL. They went through a sequence of steps to include holding the RPMs at 1800 and the 2500 for about 5-10 minutes until one of the EGT sensors hit a certain temp, then the code cleared from the computer. They gave me the truck back and told me it would likely happen again.
Over the summer I had this happen twice more, however these times, I cleared the code, ran the truck at 1800 rpm, and the code cleared, all would be ok for a while.
Then about 1.5 weeks ago the truck had both of the mentioned codes pop up the same day, first was the P04DB, I cleared it. Then the P207F came up, it would not clear. I dropped it off at the dealership. They were initially quite responsive, and again told me that they could not find a problem with the truck from a mechanical standpoint. However, they could not get the light to clear and the truck was stuck at idle. When they were able to get the light to clear it would come back on in 10 minutes, the idle message has never gone away.
Now it has been at the dealership for 1.5 weeks, I am having issues getting them to even give me an update on the status of the truck and what they plan to do to fix it. They did provide me with a loaner, for which I am grateful to not have to rent a car. However, these are expensive trucks, and I need it for my farm.
Ford 6.0L Power Stroke Diesel :: 2005 - Puking Coolant - No Codes?
Ok so I have a 2005 f250 6.0L. It is fully bulletproofed with ARP head studs. I am running a sct anarchy on street tune. My problem is that sometimes it is "puking" coolant from the degas bottle but only a drop every now and then around the cap; it drives fine, no trouble codes, the engine and trans temp is fine and it's not blowing white smoke it still blows black smoke, and there is no coolant smell just straight diesel. What might be causing it to puke a drop of coolant every now and then?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2005 Truck With Low Boost And Gasser Codes
This isn't my truck, but I'm trying to diagnose it for a friend and I haven't seen it. He's scanning it with a high-end Matco scanner so I'm not convinced that the scanner is reading right but here's what I've got:
P0056 (2), P0161, and P0300 (random misfire detected). The first two are "gasser" codes and don't show up in the 6.0 bible code list so I'm wondering if they were added in to some of the later flashes??
The truck has a "new" OEM turbo and won't build over 18 psi of boost but, according to the owner, who is a decent mechanic, it's absolutely clean inside. Looking for about the weird codes it's throwing?
All my years of information on 6.0's was stolen with my laptop last year ....
Ford 6.7L Power Stroke Diesel :: 2011 F250 - Nine Codes / 3 Times Each - P0402 / P1249 / P0471
My 2011 F250 6.7 started throwing multiple codes a couple of weeks ago. I cleared them but they all came back at the same time. What these are pointing to? I'm assuming they're all related?
P0402 Exhaust gas flow excessive detection
P1249 Wastegate control valve performance
P0471 Exhaust pressure sensor A circuit range/performance
It throws 9 codes total, the three listed above, 3 times each.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Getting Codes Abut Transmission Range Sensor Circuit
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
Ford 6.0L Power Stroke Diesel :: 2005 - Rough Idle - Codes P0672 / P0674 / P0678
I have a 2005 f350 6.0 power stroke. I had a crank no start when hot issue. I bought an obd scanner with the torque app. IPR was at 85%. ICP pressure was low. I got the IPR out and bought a new screen because it was clogged. Upon putting in I broke the injector female side plastic connection.I bought the injector connector piece and installed it. After putting everything back together it starts but runs very rough,low power. The IPR was fixed. ICP,ipr and ficm are at good levels now.
IPR=14.7%-30%
Fcim sync=1.0
Fcim voltage=48.5
ICP pressure (idle)650-850psi
My fault codes are:
P0672 (glowplug)
P0674 (glowplug)
P0678 (glowplug).
Why it would be running/idle rough?
Ford 6.0L Power Stroke Diesel :: 2004 - Runs Bad After Diesel 911 Injector Cleaner
I filled up at the same fuel station I've filled up at for 6 months, never had a problem. I just bought a 6 liter and put some injector cleaner in on the last fill up. Ever since then, it's been running really rough and missing when cold, and even when it's warm if I really lay into it, it'll pop and sputter. The fuel in water lights been on since I bought it. I think I have a bad sensor, because it was running fine until I put that cleaner in. Since its been running rough I put in new fuel filters and drained the fuel water separator, which only had fuel in it. I don't really know what it could be, but I'm 99% sure it's an injector issue since it started only after I put fuel treatment in.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Will Not Turn Over?
I have a 2005 Ford f250 Diesel 4x4 with - unfortunately - the crappy 6.0 engine. Yesterday my Daughter parked in the yard and this morning the truck not only will not start but will not even turn over. I thought maybe the batteries were dead but that is not he case. When you turn the switch on you can hear the pump start up but it will not turn over? All the lights come on and the bell comes on when you open the door and the dashboard lights work but the thing will just not turn over. I am assuming this may be some type of electrical issue or something but whatever the problem is it just came out of the blue. Ford imo should have recalled this engine.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Sometimes Won't Start When Hot
I have an 05 f250 with 109k. Recently I turned off my truck, waited about 45 min or so and upon returning the truck would just crank and crank with no fire. After waiting about 4hrs the truck started right up like nothing was wrong.
Yesterday it did it to me again. This time I have it a small shot of starting fluid and it fired right up and ran like a champ all the way to the shop..... I got the call today from the mechanic saying I have 5 injectors that are bad, 2 glow plugs and harnesses. His quote was 2400 out the door.
Ford 6.0L Power Stroke Diesel :: 2005 - Fuel System Codes / Glow Plug Circuit Failure
So i just finished putting in new high pressure oil rail cup seals in and a new #2 injector. Truck was running great for about 5 miles and then just shut off. When I had it towed home I plugged in the super chips tuner "no tunes installed" and I have a p0460, p0463, p2290, p2291. I also have a #7 glow plug circuit failure Ive been a little neglectful in getting done.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - No Start / Crank Position And Cam Portion Sensor Codes
I have an 05 f350 6.0 that I recently bought. It was fine until a few weeks ago when it died while I was driving down the road. I pulled to the side and it started right back up like nothing happened and kept driving like normal. Skip to last weekend it did it to me twice but the second time it would not start so I plugged my programmer in and it showed p0336 crank position sensor and cam portion sensor codes (I can't remember the number of the second code) I have read a few posts that said maybe it's the icp sensor so I went ahead and replaced that with no luck. The batteries went dead from excessive cranking which I know isn't very good for my starter but I was getting a little upset.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - No Power At All When Turned Off And On
I had this truck for two months no problems yesterday went on a small trip about 50 miles in on ,the hwy. I start seeing some smoke and then no power turned off & on engine several times a little hard starting no power at all I put the pedal to the floor It barely moves ran into another super d. guy he said fuel filters , I turned around and crawled back home and changed fuel filters still no power. no codes "don't no where to start".
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - New HPOP And No Start
I got a problem with my Ford F250 6.0 Diesel. The truck got a new HPOP but still wont start. ICP show everything between 15 und 75 PSI, it raises to 75 PSI max during cranking. The IPR shows 84,75% during cranking.
We get the code P0270 and P2285 in exchange but never together. We already checked the FICM but it looks good on the inside. I now ordered a new ICP sensor....